Fagor 10iE Bedienungsanleitung

Fagor Automation S. Coop.

10iE / 20iE

10iE-B / 20iE-B

Installation/Operation Manual

Manual code: 14460141

Manual version: 1104

Software version: 1.xx

(2/35) - Installation/Operation - 10iE-20iE - (Soft: 01.xx)

INDEX

1 DRO description .........................................................................................3

1.1 Front panel........................................................................................................................ 3

1.2 Turning the unit on and off.............................................................................................. 4

2 DRO operation ............................................................................................5

2.1 Display modes.................................................................................................................. 5

2.2 Incremental, absolute and with respect to Machine Reference Zero .......................... 6

2.3 Machine Reference selection and search ...................................................................... 7

2.3.1 Home search sequence ......................................................................................................7

2.4 Operating with tools......................................................................................................... 8

2.4.1 Entering tool length ............................................................................................................. 8

2.4.2 Absolute and incremental mode ......................................................................................... 8

2.4.2.1 Absolute mode .................................................................................................................... 9

2.4.2.2 Incremental mode ............................................................................................................... 9

2.5 Special operations.......................................................................................................... 10

2.5.1 Scaling factor .................................................................................................................... 10

2.5.2 Part centering ................................................................................................................... 10

2.5.3 EDM mode ........................................................................................................................ 11

2.5.3.1 Programming the levels .................................................................................................... 12

3 DRO installation ........................................................................................13

3.1 Installation of the built-in model................................................................................... 13

3.2 Rear panel....................................................................................................................... 14

3.3 General technical characteristics................................................................................. 15

3.4 Connections.................................................................................................................... 16

3.4.1 Connection of the feedback systems ................................................................................ 16

3.4.2 Input/output connection. Connector X4 ............................................................................ 17

3.5 Easy setup....................................................................................................................... 19

3.5.1 Accessing the "Easy Setup" mode ................................................................................... 19

3.5.2 Operating mode. ............................................................................................................... 20

3.5.3 Power and machine connection ....................................................................................... 20

3.6 Installation parameters .................................................................................................. 20

3.7 Parameters to configure axis position reading and display. ..................................... 22

4 Appendix ...................................................................................................30

4.1 UL seal............................................................................................................................. 30

4.2 CE seal............................................................................................................................. 30

4.2.1 Declaration of conformity .................................................................................................. 30

4.2.2 Safety conditions .............................................................................................................. 31

4.2.3 Warranty terms ................................................................................................................. 33

4.2.4 Material returning terms .................................................................................................... 33

4.3 Error codes ..................................................................................................................... 34

4.4 Maintenance.................................................................................................................... 35

(Soft: 01.xx) - 10iE-20iE - Installation/Operation - DRO description - (3/35)

1 DRO description

1.1 Front panel Each axis display has eight 14.1mm high LEDs and another one for the minus

sign (-).

Description of LED's and keys:

ABS It stays on when operating in ab solute mode and off when in incremental

mode. To access it or quit it, press this key.

ΦIt stays on when operating in diameter mode. In this mode, the DRO displays

twice the actual axis movement. To access it or quit it, use this key if allowed

by installation parameter PAR04.

INCH It stays on whe n working in in ches and off when doing it in millimeters. To

access it or quit it, press this key.

This key togg les the display fo rmat for the rota ry axis between d ecimal

degrees and Degrees.Minutes.Seconds.

To get into and out of home search mode.

To access the special function (HOLD)

To select the axis or preset it with a certain value.

To zero the axis when the "quick zeroing" mode has been activated (see

PAR11 in the installation manual).

To turn the display off while keeping track of the axes position at all times.

To cancel or abort an operation already initiated.

To validate a preset value or another operation.

Beginning of preset when the "quick zeroing" mode has been activated (see

PAR11 in the installation manual).

Model 10iE. Editing the tool length

To change the sign of the ent ered value or chang e from fine to coarse

resolution and vice versa.

Model 10iE. It toggles between the display modes: Max, Min, Difference and

Normal.

(4/35) - DRO description - Installation/Operation - 10iE-20iE - (Soft: 01.xx)

1.2 Turning the unit on and off

It turns on automatically when applying vo ltage or afte r pressing the on /off

key.

It shows Fagor dro or the corresponding error code. See the error table and

PAR11 for more options.

Turns the DRO on or off.

Precautions

Before disconnecting this un it from mains, press this key so it sa ves the

current position.

If the unit is turned off or there is a power outage, the DRO will try to save the

current position. If it does not have enough time to safe all the data, it will

display ERROR 2 when turned back on.

(Soft: 01.xx) - 10iE-20iE - Installation/Operation - DRO operation - (5/35)

2 DRO operation

2.1 Display modes

MM / INCH conversion

To display the position of the axes either in millimeters or inches by pressing

this key depending on whether the INCH led is off or on respectively.

Fine / coarse resolution

To turn off the last decimal digit (coarse resolution) for cases in which fine

resolution is excessive, simply by pressing this key.

Number of decimals

This keystroke seq uence accesses pa rameter PAR53. The first digit

corresponds to the number of decimals to be displayed in mm and the second

digit in inches.

Decimal degrees / Degrees.Minutes.Seconds

This key toggles the display format for the rotary axis [PAR00(4)=1] between

decimal degrees and Degrees.Minutes.Seconds.

Radius / Diameter

When these mode ls are used for measurin g radii or dia meters, one can

display twice the real displacement of the axis (diameter) by pressing this key.

The Φled will t urn on or off to indicate the double or actual reading

respectively.

Notes: - This works in th is way if bit 2 of installation para meter PAR04

(radius/diameter) of the axis has been preset as “1” (commutated).

Hysteresis or minimum position value

When carrying out certain operations such as drilling hard material, EDM, etc.

the position display may fluctuate annoyingly.

In these cases, the operato r can eliminate this oscillation by selecting the

"hysteresis" mode or the "minimum coo rdinate" mode just by p ressing this

keystroke sequence to toggle from one mode to the other.

Note: To have this option available, installation parameters PAR2 0 and PAR25

must be set accordingly.

Minimum, Maximum, Difference (10iE only)

To toggle between the following display modes: Min, Max, Dif and Normal.

Min. It displays the minimum position reached by the axis.

Max. It displays the maximum position reached by the axis.

Dif. It displays the difference between the maximum and the minimum position.

Normal. It displays the current position of the axis.

(6/35) - DRO operation - Installation/Operation - 10iE-20iE - (Soft: 01.xx)

2.2 Incremental, absolute and with respect to Machine Reference Zero

A coordinate DRO displays the present coordinate of one (10iE)

or two axes (20iE).

Coordinate means the distance from one point or position with respect with

another chosen as reference.

These DROs can display the position of the axes in incremental or absolute

mode or referring to home.

The next figure shows the different position display modes:

•In Home mode, it displays the distance from the current position of the axis

to the home point chosen in the feedback system (linear or encoder).

Press this sequence to access the Home Search mode.

(ABS) •In Absolute (ABS), when th e ABS led is on , it displays the distance from

the present position of the axis to part zero (D).

(I) •In Incremental, when the ABS and "home" LEDs are off the distance from

the present position of the axis to the previous position is displayed.

Toggles between the ABS and incremental modes.

On the 20iE model, it could occur that the installation parameter PAR11(1)

has been set to “0” for this key to independently affect each axis so that one

axis can display its position in incremental mode while the other does this in

absolute. In this case, to change the display mode for a particular axis, press

one of these two sequences.

(Soft: 01.xx) - 10iE-20iE - Installation/Operation - DRO operation - (7/35)

2.3 Machine Reference selection and search

Although it is not absolutely necessary, it is recommende d to use the

reference marks (Io) of the feedback system in ord er to set a machine zero

point.

This allows th e user to refe rence the mach ine axes and re store the work

coordinates after having turned the dro off, moved the machine while the dro

was off, for safety or for any other reason.

Fagor linear encoders have reference marks every 50 mm all along its length.

In order to use these marks properly, choose an area on the axis, for example

in the middle of the measuring length or at one end. Approach this area and

carry out the home sea rch. Once the reference mark has be en found, mark

this area with a marker or sticker in order to carry out the home search in the

same area in la ter occasions and make sure that you are using the same

machine zero point (home).

Fagor also offers encoders with distance-coded reference marks every 20, 40

or 100 mm. When using these distance-coded reference marks, there is no

need to move to the 0 position to find the references, simply move a distance

equal to the gap between marks (20, 40 or 100 mm depe nding on the linear

encoder)

When using an absolute encoder, there is no need to search for the reference

marks (home).

The dro stores in its internal memory work coordinates such as machine zero,

absolute and incremental.

2.3.1 Home search sequence

For encoders with regular reference marks, move the axis to the home area.

Access or exit the home search mode.

The axis displays blink showing " r " if the axis has not been homed or

" r on" if it has found the references (home).

Select the axis to be referenced (homed)

The selected axis blinks until a reference mark is de tected. The reference

signal presets the axis display au tomatically with the value of PAR10, 0.000

mm by default.

If the encoder does not have a reference mark, move the axis to the desired

position and press this key.

(8/35) - DRO operation - Installation/Operation - 10iE-20iE - (Soft: 01.xx)

2.4 Operating with tools

It is possible to define a tool and later compensate for its length while

machining.

2.4.1 Entering tool length

The Y axis blinks waiting for the tool value to be entered.

It requests the tool length.

Enter this value pressing this keystroke sequence.

Note: Since only the length of a tool may be stored, when changing a tool, its length

must be entered again.

2.4.2 Absolute and incremental mode

We will drill the holes of the following part as moving examples in incremental

and absolute modes.

[Value]

(Soft: 01.xx) - 10iE-20iE - Installation/Operation - DRO operation - (9/35)

2.4.2.1 Absolute mode

Set the dro in absolute mode

Move the axis until the display reads [14.000] (B position) and drill the hole.

Move the axis until the display reads [37,000] (C position) and drill the hole.

Move the axis until the display reads [62,000] (D position) and drill the hole.

The displayed positio n value is always referred to the preset part zero

(datum).

2.4.2.2 Incremental mode

Set the dro in incremental mode. ABS LED off

First method: Presetting incremental zero after each drill.

Starting at point A.

Move the axis until the display reads [14.000] (B position) and drill the hole.

Set the X axis to zero. See note.

Move the axis until the display reads [23.000] (C position) and drill the hole.

Sets the X axis to zero. See note.

Move the axis until the display reads [25.000] (D position) and drill the hole.

Note: If installation parameter PAR11=1, just press the axis key, ([X]) in this case, to

zero the axis.

Second method: Presetting the relative distance with respect to the next hole.

Starting at point A

Preset the relative distance to the next hole. See note.

Move the axis until the display reads [0.000] (B position) and drill the hole.

Preset the relative distance to the next hole. See note.

Move the axis until the display reads [0.000] (C position) and drill the hole.

Preset the relative distance to the next hole. See note.

Move the axis until the display reads [0.000] (D position) and drill the hole.

ABS

(B) [14.000]

(D) [62.000]

“ABS” off

(B) [14.000]

(D) [25.000]

-14

(B) [0.000]

-23

-25

(D) [0.000]

(10/35) - DRO operation - Installation/Operation - 10iE-20iE - (Soft: 01.xx)

Notes: If installation parameter PAR11=1, the presetting sequence is: [ENTER] [axis]

[value] [ENTER].

Switching over to [ABS] mode, displays the distance to part zero (datum).

2.5 Special operations

2.5.1 Scaling factor

It is possible to apply a scaling fact or within ±9.999 for mold making

applications:

The DRO will th en show the axis position resulting from multiplying its real

position by the 'value' of the scaling factor.

2.5.2 Part centering

Note: This feature is available when none of the axes have installation

parameter PAR04(2)=1 (radius/diameter commutable).

Part centering can be done as follows:

- Set the dro in absolute mode.

- Touch one side of the part with the tool.

- Set the readin g to zero pressing for an axis [ CLEAR] [X] for one axis or

[CLEAR] [Y/Z] for the other one (20iE).

- Take the tool to the other side of the part and touch this with it.

- Press the sequence [1/2] [X] for one axis or [1/2] [Y/Z] for the other (20iE).

The DRO will display half of the distance covered by the tool.

- Retract the axes until the displays read 0.000 0, the tool can be placed

exactly at the center of the part.

[factor]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fagor Andere Handbücher

Fagor

Fagor MZ-80V Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch