F&F BIS-413M Bedienungsanleitung

- 1 -

Electronic bistable pulse relay BIS-413M allows switching on or

off the lighting or other device from several different points by

parallel connected, momentary (bell) control switches.

The receiver is switched on after a current pulse caused by pres-

sing any momentary (bell) button connected to the relay. The

receiver is turned off after the next impulse or automatically

after the set off time. A longer pressing of the momentary but-

ton, lasting at least 2 seconds, turns on the relay permanently.

The relay will be turned off only after pressing the momentary

button again (or after a power supply failure). The supply vol-

tage is indicated by the illumination of the green LED marked

as U. Switching the relay on and the countdown to automatic

switch-off is signalled by the blinking of the red LED. Permanent

switching of the relay is signalled by continuous lighting of the

red LED.

Purpose

Functioning

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: biuro@fif.com.pl

Do not dispose of this device in the trash along with other waste! According to the Law on

Waste, electro coming from households free of charge and can give any amount to up to

that end point of collec� on, as well as to store the occasion of the purchase of new equip-

ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown

in the trash or abandoned in nature, pose a threat to the environment and human health.

BIS-413M 24V

Bistable relay with timing

switch and „memory”

contact position

- 2 -

The relay has the feature of the so-called „memory” of the con-

tact position, which means when the power supply is switched

back on, the relay will be restored to the state it was in when the

power supply was switched off.

1.Disconnect the power supply.

2.Fix the relay on a rail in the control box.

3.Connect the power wires to terminals 1-3, any polarity for AC

voltage and for DC voltage: connect „+” to terminal 3, „–” to

terminal 1.

4.Momentary switches connected in parallel connect to terminal

6 and the wire, to which terminal 3 is connected.

5.Powered receiver connect in series to terminals 11-12.

6. Set the switch-off time with the potentiometer.

BIS-413M 24V is not compatible with backlit buttons.

Mounting

Contact configuration

- 3 -

1-3 relay power supply 9÷30 V AC/DC

6 control input

10 output – break contact (passive)

11 input – COM power supply contact

12 output – closing contact (active)

Wiring diagram

- 4 -

power supply 9÷30 V AC/DC

contact separated 1×NO/NC

maximum load current (AC-1) 16 A

activation delay 0.1÷0.2 s

adjustment time 1÷12 min.

power indication green LED

signalling activation red LED

power consumption

standby 0.15 W

on 0.8 W

terminal 2.5 mm² screw terminals

tightening torque 0.4 Nm

working temperature -25÷50°C

dimensions 1 module (18 mm)

mounting on TH-35 rail

ingress protection IP20

Technical data

- 5 -

Table for loads supplied with 230 V AC:

tungsten halogen fluorescent energy-saving LED

2000 W 1250 W 1000 W 500 W 250 W

The above data are indicative and will heavily depend on the

design of a specific receiver (that is especially important for

LED bulbs, energy-saving lamps, electronic transformers and

pulse power supply units), switching frequency and operating

conditions.

For more information visit: www.fif.com.pl.

The F&F products are covered by a warranty of the 24 months

from the date of purchase. Effective only with proof of purchase.

Contact your dealer or directly with us.

F&F Filipowski sp. j. declares that the device is in conformity

with the essential requirements of The Low Voltage Directive

(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE.

The CE Declaration of Conformity, along with the references to

the standards in relation to which conformity is declared, can be

found at www.fif.com.pl on the product page.

Power table

Warranty

CE declaration

E220204

Inhaltsverzeichnis

Andere F&F Relais Handbücher

F&F

F&F BIS-411i Bedienungsanleitung

F&F

F&F BIS-408i Bedienungsanleitung

F&F

F&F MST-03 Bedienungsanleitung

F&F

F&F BIS-411i Bedienungsanleitung

F&F

F&F FW-R1D Bedienungsanleitung

F&F

F&F PCS-516UNI Bedienungsanleitung

F&F

F&F BIS-416 Bedienungsanleitung

F&F

F&F FOX HERMETIC BOX Bedienungsanleitung

F&F

F&F PK-1P Bedienungsanleitung

F&F

F&F PK-3P Bedienungsanleitung

F&F

F&F BIS-410i Bedienungsanleitung

F&F

F&F PCS-516 DUO Bedienungsanleitung

F&F

F&F FW-R1P Bedienungsanleitung

F&F

F&F CP-721-FPV Bedienungsanleitung

F&F

F&F PCS-506 Bedienungsanleitung

F&F

F&F BIS-411B-LED Bedienungsanleitung

F&F

F&F BIS-412M 24V Bedienungsanleitung

F&F

F&F PP-2Z Bedienungsanleitung

F&F

F&F EPP-618 Bedienungsanleitung

F&F

F&F PP-1Z-LED Pico Bedienungsanleitung

F&F

F&F BIS-411-LED Bedienungsanleitung

F&F

F&F BIS-404 Bedienungsanleitung

F&F

F&F BIS-413M-LED Bedienungsanleitung

F&F

F&F PCS-516UNI Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung