FBII OMNI-848 Bedienungsanleitung

G

:

V

6

,









8VHU*XLGH

ARMED

READY

STAY

BYPASS

INSTANT

CODE

ARMED

READY

STAY

BYPASS

INSTANT

CODE

1 3

4 6

7 9

STAY INSTANT

BYPASS CODE

ARM

AC / LB

READY

STAY

INST

LO BATT

SPRV.

N9939 8/00

FIRE BURGLARY INSTRUMENTS, INC.

- 2 -

Table Of Contents

QUICK REFERENCE............................................................................................................... 3

INTRODUCTION ...................................................................................................................... 5

SYSTEM REFERENCE............................................................................................................ 6

TURNING THE SYSTEM ON................................................................................................... 9

TURNING THE SYSTEM OFF...............................................................................................12

USER CODES........................................................................................................................13

MISCELLANEOUS COMMANDS ......................................................................................... 14

TESTING THE SYSTEM........................................................................................................ 19

RECOMMENDATIONS ON SMOKE DETECTORS.............................................................20

EMERGENCY EVACUATION ............................................................................................... 21

GLOSSARY............................................................................................................................22

FCC STATEMENT ................................................................................................................. 20

TELEPHONE OPERATIONAL PROBLEMS........................................................................20

LIMITATIONS OF THIS ALARM SYSTEM...........................................................................21

LIMITED WARRANTY ........................................................................................................... 23

- 3 -

4XLFN5HIHUHQFH

TO TURN SYSTEM ON

1. Check to make sure the system is ready, The On/Off (ARM) light will light

(Green READY light is lit).

2. Enter your 4-digit user code.

3. Exit through a door designated by your installer as an exit/entry door.

TO TURN SYSTEM OFF

1. Enter through a door designated by your installer as an exit/entry door

2. Enter your 4-digit user code.

3. The system On (ARM) light will go out.

TO TURN SYSTEM ON AND STAY INSIDE

1. Check to make sure the system is ready (Green READY light is lit).

2. Press STAY .

3. Enter your 4-digit user code.

The On/Off (ARM) light and the STAY light will both light.

REMEMBER: You must turn the system Off if you want to open the door or leave

the premises after the exit time has passed.

TO TURN THE SYSTEM ON: INSTANT MODE, AND STAY INSIDE

1. Check to make sure the system is ready (Green READY light is lit).

4. Press INSTANT .

5. Press STAY .

2. Enter your 4-digit user code.

The On/Off (ARM) light, the INSTANT light, and the STAY light will all be on.

TO RESET SMOKE DETECTOR

1. Enter your 4-digit user code twice.

- 4 -

4XLFN5HIHUHQFH

The following table lists the “Quick Commands” available with this control.

Key Description Keypads Comments

# 1 Quick Arm - If system is

ready All keypads Allows you to arm the system without requiring your user code.

User code is always needed to disarm the system, though.

# 2 Force Arm - bypasses faulted

zones All keypads Allows you to arm the system even if some zones are faulted.

These zones will be automatically bypassed and will be

unprotected.

Bypass

zone Quick Bypass - All keypads If not enabled requires user code with authority 1,2 or 3

# 3 Set Time All keypads May require user code

# 4 Zone Dir LCD only Mode terminates after last enabled zone

# 50 Quick Help LCD only

# 51 Show Time LCD only May also require code

# 52 Show Auto LCD only May also require code

# 53 User log view LCD only Also, needs user code with authority level 1 or 2

# 54 Set Auto Time of current

part. All keypads by partition, need user code

# 55 Display Firmware Version LCD only

# 56 Display Key Fob Low

Batteries. All keypads

# 57 Door Strike All keypads May require certain user code

# 58 Change/View Pager number All keypads For keypad partition, only LCD shows phone number

# 6 Display/Toggle Chime Mode All keypads LCD displays current state first, then offers to toggle. All

others just toggle the state.

# 7 Assign user to other

partitions All keypads Need user Auth. Of 1 or 2. Digit 4 (P) enables user to page.

Paging must be enabled and turned on.

# 8 User Page Toggle All keypads Toggles if users should send page for O/C by partition

# 9 User On-line All keypads Connects to downloader while on line, disconnects home phone.

# 0 Multi-Part All keypads LCD displays current enables, 1,2,3,P - P=

- 5 -

Introduction

Congratulations on your decision to protect your home or business with the OMNI-

848 security system. You have chosen a reliable, state-of-the-art security system

that is remarkably easy to operate. Your system has been professionally installed

by your local Security Company whose representative can explain the specifics of

your system.

The keypad is the input and display device for your security system. Your Security

Company representative will suggest the model most appropriate for your premises

and your needs. There are three types of keypads that can be used with this system:

LCD keypad (alpha display), Fixed-Glass keypad (2-digit display), LED keypad.

Since your system may use any of these keypads, the displays of all keypads are

described in this manual.

The OMNI-848 is listed by Underwriters Laboratories for Household Fire and

Burglary applications.

Throughout this manual, the following conventions are used to represent the

keystrokes required to perform the following functions.

STAY Press Button labeled STAY.

BYPASS Press Button labeled BYPASS.

INSTANT Press Button labeled INSTANT.

CODE Press Button labeled CODE.

Enter 4-digit or 6-digit user code (see User Code note on page 8).

Please keep your manual in a convenient location so you can refer to it if

needed.

- 6 -

System Reference

ZONE DESCRIPTIONS

In the following table, enter a description of the area of protection for each zone.

Example: Zone 1 Windows on North side of building

Zone 4 Main entrance to building.

Zone Description Zone Description

125

226

327

428

529

630

731

832

933

10 34

11 35

12 36

13 37

14 38

15 39

16 40

17 41

18 42

19 43

20 44

21 45

22 46

23 47

24 48

Entry time ________ Door __________ Exit time ________

Entry time ________ Door __________

Exit time is the same for all designated entry/exit doors.

- 7 -

System Reference

(cont)

SEND-HELP ALERT

All keypads are equipped with emergency-pair keys. In order to

activate the alert, both keys must be pressed at the same time. The type

of keypad you have installed dictates which keys you press. Your installer will

show you how to activate these emergency keys. The emergency keys used for

all keypads are shown below.

The following SEND - HELP ALERT is programmed into my system:

KEYS DESCRIPTION

[#] & [✱] __________________________________

[7] & [9] __________________________________

[1] & [3] __________________________________

PAGER ALERT

If programmed, a button on a designated keyfob may also be used to send an

alert message to a pager. Ask you installer if this was done.

MONITORING STATION INFORMATION

Account #

Telephone #

- 8 -

System Reference

(cont)

USER CODE ASSIGNMENTS

In the following table, enter the names of the individuals assigned to each user

number.

User Assigned To… User Assigned To…

133

234

335

436

537

638

739

840

941

10 42

11 43

12 44

13 45

14 46

15 47

16 48

17 49

18 50

19 51

20 52

21 53

22 54

23 55

24 56

25 57

26 58

27 59

28 60

29 61

30 62

31 63

32 64

____ ____ USER CODE NOTE: User codes can be either 4 digits or 6 digits, depending

4-digit 6-digit on installer programming. Ask your installer what type of user codes (4- or 6-digits)

are being used in your system. When performing system functions, you must use

the appropriate 4 or 6-digit user codes.

- 9 -

Turning The System On

IS THE SYSTEM READY?

You can turn the burglar portion of your security system on and off. Before you

can turn the system on, it must be “ready.” If you have a protected door open, or

someone is moving in view of a motion detector, the system will not display

“READY.”

The system is ready if the READY light and the display shows:

LCD Keypad:

SYSTEM READY

PART 1

Fixed-Glass Keypad:

Ready LED lit LED Keypad:

Ready LED lit

TO TURN THE SYSTEM ON AND LEAVE

Enter your user code.

The System On (ARM) light will go on and the display will show:

LCD Keypad:

ON: AWAY

PART 1

Fixed-Glass Keypad:

Arm LED lit LED Keypad:

Arm LED lit

Exit through a door designated by your installer as an exit/entry door. You

must leave within the exit time programmed by your installer. Refer to the

reference sheet for the time that has been set for your system.

WHEN THE SYSTEM IS NOT READY

If the system is not ready to be armed, the READY light will be off and the

display will show which zone or zones are not ready. The following conditions

will be indicated by the zone lights (LED keypad) or described on the display:

Fast Blink .............................Alarm or tamper condition

Slow Blink/Low Intensity Bypass

Slow Pulse ............................Trouble, problem with RF receiver, or low battery

Solid On .................................Zone faulted

Example: If the READY light is not lit and the Zone 1 light is solid on, an

alarm sensor on Zone 1 is faulted. This might mean that a door is open or

someone is walking in view of a motion sensor. Check all sensors on Zone 1 and

resolve the problem. When all sensors are restored, the READY light will come

on and the zone light will go out. In this example, the display shows:

NOT READY

PART 1 and NOT RDY ZN 1

FRONT DOOR

- 10 -

Turning The System On

(cont)

Determine which zone or zones are not ready, resolve the problem, and turn the

system on normally. If the problem cannot be resolved, you may bypass the

zone that is not ready. Bypassing should only be done if the problem on the

zone cannot be resolved, OR if you intentionally wish to leave the zone off. For

example, you would leave the zone off if you plan to keep the window open for

ventilation. Zones that are bypassed are not protected when the system

is on. See Bypass on the following page for a description of the procedure.

TO TURN THE SYSTEM ON AND STAY INSIDE

To turn the perimeter portion of your burglar alarm on and move around freely

inside the premises, use the STAY mode.

Check to make sure the system is ready. When it is ready, press:

STAY followed by your user code.

When the system has been turned on successfully, the On/Off (ARM) light and

the following will display:

LCD Keypad:

ON: STAY

PART 1

Fixed-Glass Keypad:

STAY LED Keypad:

Arm and Stay LEDs lit

REMEMBER: You must turn the system off if you want to open the door or

leave the premises after the exit time has passed.

TO TURN THE SYSTEM ON IN INSTANT MODE AND STAY INSIDE

In INSTANT STAY mode, the perimeter portion of your burglar alarm system

is on but the time delays are eliminated from your normal entry/exit door(s). All

interior protection is off, so you are free to move around inside.

Check to make sure the system is READY. When it is ready, press:

INSTANT followed by

STAY followed by your user code.

When the system has been turned on successfully, the On/Off (ARM) light, the

INSTANT light, and the STAY light will all be on, and the following will display:

LCD Keypad:

ON: STAY / INS

PART 1

Fixed-Glass Keypad:

STAY

INSTANT

LED Keypad:

Armed, Stay, and Instant

LEDs lit

NOTE: This system can be programmed by the installer for the AUTOSTAY

feature which automatically bypasses interior zones if you arm the system and

do not exit through a delay zone during exit time.

Andere Handbücher für OMNI-848

Inhaltsverzeichnis

Andere FBII Sicherheitssystem Handbücher

FBII

FBII OMNI-408EU Bedienungsanleitung

FBII

FBII XL-2S Silver Bedienungsanleitung

FBII

FBII XL-2 Bedienungsanleitung

FBII

FBII XL-2T Bedienungsanleitung

FBII

FBII XL-2 Platinum Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

FBII

FBII XL-5 Bedienungsanleitung

FBII

FBII XL4600RM Bedienungsanleitung

FBII

FBII XL-20 Bedienungsanleitung

FBII

FBII OMNI-400 EU Montageanleitung

FBII

FBII XL-2P Bedienungsanleitung

FBII

FBII XL-21 Bedienungsanleitung

FBII

FBII LEGEND SERIES Bedienungsanleitung

FBII

FBII XL-1S Bedienungsanleitung

FBII

FBII XL Star 4500 Bedienungsanleitung

FBII

FBII XL-20 Bedienungsanleitung

FBII

FBII XL-21 Bedienungsanleitung

FBII

FBII XL-2 Bedienungsanleitung

FBII

FBII Star XL4800 EZ Bedienungsanleitung

FBII

FBII XL-21 Bedienungsanleitung

FBII

FBII XL4600DL Bedienungsanleitung

FBII

FBII LEGEND 7100 Bedienungsanleitung

FBII

FBII Star XL4800EZ Bedienungsanleitung

FBII

FBII XL-4 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung

Pego

Pego ECP APE03 Bedienungsanleitung