Federal Signal Corporation Signalmaster 330132 Bedienungsanleitung

2561063B

REV. B 1002

Printed in U.S.A.

INSTRUCTION SHEET

FOR

SIGNALMASTER™ MODEL 330132

SAFETY MESSAGE TO INSTALLERS AND USERS

People’s lives depend on your safe installation of our

products. It is important to read, understand and follow all

instructions shipped with the products. In addition, listed

below are some other important safety instructions and

precautions you should follow:

• To properly install this light: you must have a

good understanding of automotive electrical

procedures and systems, along with proficiency

in the installation and use of safety warning

equipment.

• DO NOT install equipment or route wiring in

the deployment path of an air bag.

• When drilling into a vehicle structure, be sure

that both sides of the surface are clear of any-

thing that could be damaged.

• In order for the light to function properly, a

good ground connection must be made. At a

minimum, it must be attached to a solid metal

body or chassis part that will provide an effec-

tive ground path as long as the light system is

to be used.

• Locate light control so the VEHICLE and

CONTROL can be operated safely under all

driving conditions.

• Do not attempt to activate or deactivate light

control while driving in a hazardous situation.

• You should frequently inspect the light to en-

sure that it is operating properly and that it is

securely attached to the vehicle.

• File these instructions in a safe place and refer

to them when maintaining and/or reinstalling

the product.

Failure to follow all safety precautions and instruc-

tions may result in property damage, serious injury, or

death to you or others.

I. GENERAL.

The Federal SignalMaster™ Model 330132 is an

economical, low profile, solid state, directional light control

that is designed to operate with the Federal Signal six-

lamp directional light assembly. The unit is reversed

polarity protected to avoid damage if the positive and

negative power connections are connected incorrectly.

This model provides three distinctive directional

signals: left arrow, right arrow, and center out. In addition,

an alternating flash pattern produces a warning signal for

use when a directional signal may not be appropriate.

When a directional signal is selected, the lamps are

individually illuminated in a sequential sweeping motion

until all six lamps are illuminated.

II. SPECIFICATIONS.

Input Voltage 11VDC to 16VDC.

Polarity Negative ground only.

Operating Temperature -30°C to +65°C.

Range

Standby Current Zero amperes.

+BAT Fuse 25 amperes.

+IGN/BAT Fuse 1 ampere.

Output Drive 6, 27 watt lamps.

Capability (Total)

Flash Rate:

Directional 35 patterns/min.

Warn 60 patterns/min.

Dimensions:

Height 1-1/2"

Width 6-1/8"

Depth 5"

Shipping Weight 2.0 lbs

III. INSTALLATION.

A. SignalMaster Light Assembly.

Install the light assembly as described in the

instructions packed with the mounting kit. Route the cable

near the eventual location of the control unit.

B. Control Unit.

WARNING

When installing equipment inside air bag equipped

vehicles, the installer MUST ensure that the equip-

ment is installed ONLY in areas recommended by

the vehicle manufacturer.

Failure to observe this warning will reduce the

effectiveness of the air bag, damage the air bag, or

potentially damage or dislodge the equipment,

causing serious injury or death to you or others.

See figure 1. The supplied mounting bracket

allows the control unit to be mounted in a variety of

positions. To install the control unit, proceed as follows:

C. Electrical Connections.

WARNING

Failure to observe this WARNING may result

in fire, burns or blindness.

If shorted to vehicle frame, high current conductors

can cause hazardous sparks resulting in electrical

fires or molten metal.

DO NOT connect this system to vehicle battery until

ALL other electrical connections are made and

mounting of all components is complete.

Verify that no short circuits exist, before connecting

to the Positive (+) battery terminal.

The control unit is supplied with a six-position

connector and a eleven-position terminal block to perform

the electrical installation. User-supplied, 14-gauge red and

black wires are required for the (+) BAT and (-) GND

connections on the six-position connector. User-supplied,

18-gauge red and green wires are required for the (+) BAT/

IGN and CASE GROUND connections on the six-position

connector. Using figure 2 as a guide, complete this portion

of the installation as follows:

1. Power Connections.

CAUTION

To avoid damage and ensure proper operation, the

red and black wires MUST be installed in the six-

position connector as shown in figure 3.

WARNING

Do not connect more than one, 6 or 8 head,

halogen SignalMaster assembly to a

SignalMaster controller or the SignalMaster

outputs of a SmartSiren. Electrical fire or

damage to the controller or siren will result.

Figure 1.

CAUTION

Install the control unit in an adequately ventilated

area. Never install near heater ducts.

NOTE

When selecting a mounting location for the control

unit, it is necessary to keep in mind that the Signal

Master cable is 15-feet long. Plan wiring and cable

routing before installation.

1. Select a mounting location for the control unit

that allows the vehicle and controls to be operated safely at

all times.

2. Use the mounting bracket as a template and

scribe two drill position marks at the selected mounting

location.

CAUTION

Before drilling holes in ANY part of a vehicle, be

sure that both sides of the mounting surface are

clear of parts that could be damaged; such as brake

lines, fuel lines, electrical wiring or other vital parts.

3. Drill two holes at the previously scribed

position marks.

4. Secure the mounting bracket to the mounting

surface with two user-supplied, thread-forming, 1/4-20

screws.

-2-

Figure 2.

Figure 3.

a. Strip 1/4" of insulation off of each wire.

See figure 3. Use small blade screwdriver to depress spring

in connector, insert proper wire and remove screwdriver to

release spring.

b. Connect the red and black 14-gauge wires

to the connector as shown in figure 3.

c. Route the red and black 14-gauge wires

through the firewall and toward the battery. Connect the

black wire to a good frame ground near the battery. In

most vehicles, a wire from the negative terminal of the

battery is routed and attached to the body/frame at the

fender. This is a convenient point to connect the 14-gauge

black wire. Do not connect the red wire to the (+) positive

terminal at this time.

d. Connect the 18-gauge red and green wires

to the connector as shown in figure 3.

IMPORTANT

The 18-gauge red wire’s termination point deter-

mines when the directional signal can be activated.

When the wire is attached to a vehicle fuse that is

powered when the ignition switch is in the run or

start position, the vehicle’s ignition switch must be

in the run or start position to operate the directional

signal. When the wire is attached to the vehicle bat-

tery, the directional signal can be operated at any

time. Note that the unit draws no current when in

the “off” position.

e. Select the desired termination point. As

applicable, route the 18-gauge red wire toward the vehicle

fuse block or through the firewall toward the battery.

Install a user-supplied, 1-ampere, in-line fuse in the 18-

gauge red wire as close to the power source as possible and

terminate as required.

f. Route the 18-gauge green wire to a known

good chassis ground near the control. To provide a good

ground connection, scrape any painted surface to bare

metal and terminate as required.

g. Ensure that positions 5 and 6 of the six-

position connector are not used (see figure 2).

h. Plug the six-position connector into the

mating connector on the control unit, and apply pressure

until it locks into place.

2. SignalMaster Cable Connections.

a. Route the SignalMaster cable towards the

control unit, while being careful not to scrape the wires on

any sharp edges.

b. If necessary, cut the cable to the appropri-

ate length.

c. Connect six 22-gauge wires and 16-gauge

red wire to the terminal block as shown in figure 2.

Positions 1, 8, 9, and 10 are not used. Cut the unused white

and blue wires at the cable's insulating sheath.

D. Inspection and Final Installation.

1. Ensure that there are no loose wire strands or

other bare wires which may cause a short circuit. Also, all

wires must be protected from any sharp edges which could

eventually cut through the insulation.

2. Connect the remaining end of 14-gauge red

wire from the six position connector to the (+) positive

terminal of the battery with an in-line, user-supplied

fuseholder and 25A fuse. Locate the fuse as near the

battery as possible to protect the entire length of wire.

3. Read and understand paragraph IV OPERA-

TION, and test for proper operation of all functions.

4. Secure the mounting bracket to the control

unit with the 1/4-20 hex head, thread forming screws and

1/4" external tooth lock washers (see figure 1).

IV. OPERATION.

SAFETY MESSAGE TO OPERATORS

Peoples’ lives depend on your safe use of our products.

Listed below are some important safety instructions and

precautions you should follow:

• Although your warning system is operating

properly, it may not be completely effective.

People may not see or heed your warning signal.

You must recognize this fact and continue

driving cautiously.

• Also, situations may occur which obstruct your

warning signal when natural or man-made

objects are between your vehicle and others,

such as: raising your hood or trunk lid. If these

situations occur, be especially careful.

• At the start of your shift, you should ensure

that the light is securely attached and all lamps

are operating properly. The LED display on the

control only simulates the operation of the lamps.

• If a selected function does not perform properly

or if any of the lamps remain illuminated when

the control is off, disconnect the power connector

from the control unit and contact the nearest

service center.

Failure to follow these safety precautions may result in

property damage, serious injury, or death to you, to

passengers, or to others.

RETAIN AND REFER TO THIS MESSAGE

-3-

See figure 4. All controls utilized during normal

operation of the SignalMaster directional light are located

on the front panel of the control unit. The LED display

simulates the light pattern being executed by the direc-

tional light.

A. Slide Switch.

1. LEFT (Position 1).

In this position, the light produces a left arrow

flashing pattern, instructing traffic to move left.

2. CENTER OUT (Position 2).

In this position, a center out flashing pattern

is produced, instructing traffic to move around either side

of the vehicle.

3. RIGHT (Position 3).

In this position, the light produces a right

arrow flashing pattern, instructing traffic to move right.

B. WARN switch.

When this switch is pressed, an alternating

pattern is produced. The two middle lights activate

alternately with the two outside lights on each side. This

pattern will override any of the slide switch functions.

V. SERVICE.

A. General.

Servicing, other than cosmetic features, should be

performed by a qualified Federal Signal service center. If

the control unit is not working properly, disconnect all

electrical connections starting with the six-position power

connector. Remove the control unit from the mounting

bracket. Send the unit to the nearest authorized service

center or the Federal Signal service department.

Communication and shipments should be addressed to:

Service Department

Federal Signal Corporation

2645 Federal Signal Drive

University Park, IL 60466

1-800-433-9132

After servicing is complete, perform a test of all

functions to ensure the control unit is operating properly.

B. Replacement Parts List.

Description Part Number

Printed Circuit Board Assembly 2001135

Knob, Pushbutton 8573065

Knob, Slide Switch 8536C1041

Bezel, Slide Switch 8573060

Connector, Female, 6-Position 140325-04

Bracket, Mounting 8573070

Screw, Hex Head, Mounting 7011164B-08

Lockwasher, 1/4" 7075078

Chassis 8573068

Cover 8573066

Microprocessor SM1CB100

-4-

Figure 4.

Andere Federal Signal Corporation Controller Handbücher

Federal Signal Corporation

Federal Signal Corporation SignalMaster 330104 SMC1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UNITROL Omega 8000 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 2001-AC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice UVIC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SmartSystem SS2000C31 Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation SignalMaster 330104 SMC1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ultravoice UV Einrichtungshandbuch

Federal Signal Corporation

Federal Signal Corporation SS2000+ ? Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice UVRI-B Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SignalMaster SMC14 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ultravoice UV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIGNALMASTER 331102 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DCFCB Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation SmartSystem SS2000-LMS Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation FC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation PAGASYS GEN II Bedienungs- und Montageanleitung

Federal Signal Corporation

Federal Signal Corporation SignalMaster 331105 SMC5 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice Einrichtungshandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch