Federal Signal Corporation CP-PB Series Bedienungsanleitung

Limited Warranty: This product’s limited warranty can be found at www.fedsig.com/SSG-Warranty

SAFETY MESSAGES TO INSTALLERS AND USERS : Products should be installed by a licensed electrician and follow

all safety instructions. Failure to do so may result in property damage, serious injury, or death.

• Read and understand all instructions before installing or operating this equipment.

• To avoid electrical shock hazards, do not connect wires when power is applied. Failure to observe this warning may

lead to serious injury or death.

• Never alter the unit in any manner. Safety in hazardous locations may be endangered if additional openings or other

alterations are made in units specically designed for use in these locations.

• Do not connect this station to the system when power is on.

• After installation, ensure that all threaded joints are properly tightened.

• Keep the unit tightly closed when in operation.

• After installation, test the station and the system to ensure that it is operating properly.

• After testing is complete, provide a copy of this instruction sheet to all personnel.

• Establish a procedure to routinely check the station and system for proper activation and operation.

Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death.

Certications

ATEX and IECEx Certication Information:

Certicate Nos. ATEX Cert No.: DEMKO 19 ATEX 1939X

IECEx Cert No.: IECEx UL 19.0074X

ATEX coding II 2 G D

Protection II 2 G Ex db eb mb IIC T4 Gb (Tamb= -40°C to +70°C)

CP-BG models: II 2 D Ex tb IIIC T100°C Db IP66

CP-PB models: II 2 D Ex tb IIIC T100°C Db IP65

EN60079-0, EN60079-1, EN60079-7, EN60079-18, EN60079-31, IEC60079-0, IEC 60079-1, IEC60079-7, IEC60079-18,

IEC60079-31

Refer to Certicates for specic standard versions.

Specic Conditions of Use

1. The equipment has an optional protective non-metallic cover that may provide a potential electrostatic charging

hazard.

Manual Call Point

Pushbutton and Break Glass Stations for Use in

Hazardous Locations

25500424 Rev A2 0522

2Federal Signal signaling.fedsig.com

2. The equipment has an optional metallic break glass hammer mounted to the enclosure, which can store electrical

charge and therefore may provide a potential electrostatic charging hazard. The metallic break glass hammer has

a capacitance of 94pF.

3. These devices reach a temperature of 85°C at the entry point.

Construction Products Regulation (CPR) Certication Information

2821

1. Model Designation: CP-BG-x-x-x-xxx-xx-x

2. Description: Manual call point for re detection and re alarm systems for buildings.

3. Declaration of Performance No.: 0843-CPR-1073, 2821-CPR-0207. (To access it: Go to www.fedsig.com, search

model “CP-BG” to access product webpage, click “Resources” tab. The document is located under “Agency

Certicates” section)

4. Standard Applied: EN54-11:2001/A1:2005.

5. Identication Number of Notied Product Certication Body: 2821 (CE), 0843 (UKCA).

6. Manufacturer: Federal Signal, 2645 Federal Signal Drive, University Park, IL 60484

7. EU Auth. Rep: FS VAMA, Doctor Ferran 7, 08339 Vilassar de Dalt, Spain. UK Auth. Rep: Victor Products, Unit 3A,

Tyne Dock East Side, Port of Tyne, South Shields, NE33 55Q, ENGLAND.

8. Marking Year for CE and UKCA: 2022

Conditions for Safe Use

1. This device has been tested for a voltage range of ± 10%.

2. Do not install Test Reset Key. Key may only be installed for applications not requiring EN54-11 certication.

3. To enable correct installation and operation, review all sections in this manual #25500424A for all technical,

installation, and maintenance data.

UL-C-UL Signaling Certication Information (Model CP-PB Series)

1. UL Certication applies to push button models series CP-PB Series only. CP-BG models are not UL/C-UL Listed.

2. For use in Non Monitoring (NM) and Self Monitoring (SM) Emergency Signaling Applications.

3. Not for use with Fire Alarm or Fire EVAC Applications. Product can not be marked “FIRE” or “EVAC.”

4. Ambient temperature rating: -40°C to +60°C.

5. Input Ratings: 48 Vdc, 3 A (max).

6. This product is not provided with a preassembled conduit hub. A Listed hub shall be used and shall be connected

to the conduit before the hub is connected to the enclosure.

7. Only the models with sufx “5” (No Red color and with tactile marking - see nomenclature below) can be used in

public emergency alarm reporting systems and emergency communications systems (ECS) in accordance with

NFPA 72.

Table 1 Callpoints Model Designation

Prod

Family

Activation Entries Color Switch/Witing Term Left Flap/Hammer Indicator LED Certication

CP-PB: Push

Button

M: Metric

N: NPT

Y: Yellow

K: Black

G: Green

B: Blue

R: Red

S: Single, Clamp term

D: Dual, Clamp term

L: LED Dual, Clamp term

1: SIngle, Screw term

2: Dual, Screw term

3: LED Dual - Screw term

NNN: None

FNN: +Flap, No label

no hammer

FAN: +Flap, + Activate

label, No hammer

00: None

06: Indicator LED, 6 V

12: Indicator LED, 12 V

24: Indicator LED, 24 V

48: Indicator LED, 24 V

4: UL

5: UL w/NFPA72

tactile markings

(NO RED COLOR

OPTION ALLOWED)

Federal Signal signaling.fedsig.com

UL/C-UL Hazloc Zones Certication Information (Model CP-PB Series)

1. Zones Protection Ratings:

Class I, Zone 1, AEx db eb mb IIC T4 Gb

Ex db eb mb IIC T4 Gb

Zone 21, AEx tb IIIC T100°C Db

Ex tb IIIC T100°C Db

(Tamb= -40°C to +60°C)

2. Class and Division Hazardous (classied) Location Ratings:

Class I, Division 2, Groups A, B, C and D (T4).

3. UL Certication applies to push button models CP-PB Series only. CP-BG models are not UL/C-UL Listed.

4. Input Ratings: 48 Vdc, 3A (max).

5. WARNING — Do not open when energized or within an explosive or dust atmosphere.

6. WARNING — Potential electrostatic charging hazard. The equipment may contain an optional protective non-

metallic cover, which may provide a potential electrostatic charging hazard. Mitigation should be taken by

the end user, using local Explosive Atmosphere (Ex) Electrical installations design, selection, inspection, and

maintenance Codes and Standards.

Model Descriptions and Accessories

Federal Signal Manual Call Points Stations are available in two base models (PB – Push Button and BG – Break Glass),

both providing the following standard and eld customizable features:

• High-impact resistant glass-reinforced polyester (GRP) thermoset plastic housing and faceplate for corrosion

resistance

• -40°C to 70°C ambient operational coverage

• Static-dissipative GRP housings and faceplates

• One or two switches available (two switches unavailable with LED option factory installed)

• Three M20 or 1/2-inch NPT threaded entryways

• 180° rotatable rear housing with respect to front housing for top or bottom dual conduit feeds, with a single left or

right feed.

• Color-coded front replaceable faceplate (red, yellow, green, blue, black)

• Front face visual status indicator (the white triangles)

• Reset keyway that may be installed on unit or used separately

NOTE: CP-BG-x-x-x-xxx-xx-2 (EN 54-11) models will NOT have the keyway installed in actual applications; it is only to

be used separately as a discrete keyway and will be included separately as such.

• Removable internal wiring block/mounting plate for wiring ease, if desired

• Input wiring block types available:

• 9-position cage-clamp design, or a

• 9-position screw-down design

• Faceplate labels:

• Eight adhesive-backed labels are supplied for eld installation: FIRE, EVAC, BIOHAZARD, GAS, EMERGENCY,

SHUTDOWN, LOCKDOWN, and Evac Logo (white or black on clear background)

• Stainless steel faceplate labels are available as an option (separate service part # for eld installation) for

FIRE, EVAC, GAS ALARM, or BIOHAZARD ALARM (black text on stainless steel background)

4Federal Signal signaling.fedsig.com

• Special applications (e.g., language, specic artwork, site location, etc.): The faceplate’s labeling surface

will accept user-supplied Uline 1.75-inch by 1/2-inch weather resistant labels for laser printers, Uline part #

S-19297.

• Custom stainless steel Duty Label (separate service part # for eld installation): Side mounted on either PB or

BG units (except BG units that have a break glass hammer bar already installed). Consult the factory for lead

times, as this is a customized part for user-specic installation.

Model CP-PB Call Point Push Button activated

• 1-3/4-inch (44.5 mm) diameter spring return black thermoset plastic push button

• Protective faceplate wall shroud about the button and status indicator

• Optional bi-color LED status light indicator

Model CP-BG Call Point Break Glass activated

• Replaceable break glass panel covered with a protective polyester label to limit

glass particle fallout

• Protective faceplate wall shroud about the status indicator

• EN 54-11 approved British Standard model available (NOTE: Reset Keyway must

not be installed during operation)

• Optional side mounted break glass hammer bar

• Optional bi-color LED status light indicator

Federal Signal Manual Call Point Stations are available with the following optional features factory installed:

• 6 V, 12 V, 24 V or 48 V LED bi-color status indicator

• High-impact-resistant clear polycarbonate cover ap with or without various instructional labels (e.g., LIFT COVER,

BREAK GLASS TO ACTIVATE) on interior face of the cover ap

• Side mounted stainless steel break glass hammer bar on BG stations

• Single and dual switches

• EN54-11 certied Break Glass stations

Federal Signal Manual Call Point Station may be eld serviced with the Service/Accessory Kits specied within Table 2

on “Table 2 Call Points Field Installed Service/Accessory Kits” on page 23.

Unpacking the Call Points Station

After unpacking the station, examine it for damage that may have occurred in transit. If it has been damaged, do not

attempt to install or operate it. File a claim immediately with the carrier, stating the extent of the damage. Carefully

check all envelopes, shipping labels, and tags before removing or discarding them. If any parts are missing, please call

Federal Signal Customer Support at +1 708-534-4756 or +1 800-446-6809.

Opening / Closing the Call Point for Internal Access

The Federal Signal Call Point stations have two chambers within their designs, the rst being a front chamber housing

the stainless steel mechanical hardware, and the rear chamber housing the activation switch and an internal wiring block

with housing provisions for M8 or 1/4-inch mounting hardware through the four corner slotted openings.

NOTE: The design is such that the rear chamber may be accessed with no need to open the front chamber.

Federal Signal signaling.fedsig.com

Tools needed to access both chambers:

• #2 Philips screwdriver

• 2.0 mm hexagon key

• 3.0 mm hexagon key

Call Point Front Chamber Access

The model CP-PB pushbutton station’s front chamber is easily accessed for cover ap attachment and/or maintenance

or replacement of parts. To access the front chamber:

1. Remove the pushbutton and bearing washer by unscrewing the 3/4-inch long Philips screw.

2. If present, remove the reset keyway by using a M2 hex wrench to loosen the M4 set screw below the keyway’s

triangular pointer

Figure 1 Removing the keyway

UNLOOSEN M4 SET SCREW

TO REMOVE RESET

KEYWAY AND BEARING

WASHER IF PRESENT

UNLOOSEN TWO M4

CAPTIVATED SCREWS

REMOVE

BUTTON

AND SCREW

Figure 2

ACTUATOR SPRING

PIVOT BOSSES

CLEAR

ACTUATOR

CYLINDER

SPRING LOADED

BUTTON STEM

ASSEMBLY

3. Loosen the two M4 Philips head screws at the 3:00 and 9:00 positions on the faceplate and remove the faceplate.

NOTE: These two screws are captivated to the front faceplate.

4. Upon reinstalling the front faceplate, reverse this process and apply 15 in-lb maximum of torque to the M4 Phillips

screws to ensure that the faceplate is fully seated on the front housing.

NOTE: Applying excessive torque may result in the brass threaded insert dislodging from the front housing,

rendering the unit inoperable.

6Federal Signal signaling.fedsig.com

Figure 2 Reinstalling the faceplate

UNLOOSEN TWO M4

CAPTIVATED SCREWS

UNLOOSEN M4 SET SCREW TO REMOVE RESET

KEYWAY AND BEARING WASHER IF PRESENT

Figure 4

CLEAR

ACTUATOR

CYLINDER

ACTUATOR SPRING

PIVOT BOSSES

REPLACEABLE BREAK

GLASS PANEL WITH

PROTECTIVE LABEL

GLASS PANEL

RETENTION SPRINGS

5. Model CP-BG break glass station’s front chamber is easily accessed by the following actions:

a. If present, remove the reset keyway by using an M2 hex wrench to loosen the M4 set screw below the keyway’s

triangular pointer

b. Loosen the two M4 Philips screws at the 3:00 and 9:00 positions on the faceplate and remove the faceplate.

NOTE: These two screws are captivated to the front faceplate

c. Upon reinstalling the front faceplate, apply 15 in-lb maximum of torque to the M4 Philips screws to ensure that

the faceplate is fully seated on the front housing.

NOTE: Applying excessive torque may result in the brass threaded insert dislodging from the front housing

rendering the unit inoperable.

Call Point Rear Chamber Access

All models of the Call Point station have the same rear chamber access method for internal wiring management,

mounting the unit to a vertical wall surface, and general maintenance/routine inspection.

To access the rear chamber:

1. Loosen the four captivated socket head cap M4 screws by using a M3 hex wrench at each of the front corners of

the device.

2. Carefully pull away the front housing portion from the rear, noting the limited extension length of the two halves

due to the wiring harness length.

3. Note that the rear housing unit is 180° rotatable with respect to the front housing so the two threaded entryways

can be on either the top or bottom of the installed station.

4. Upon reinstalling the front housing, screw down a pair of diagonally opposed screws rst by partially applying

18in-lb maximum of torque to the M4 socket head screws. Repeat the process to the other two diagonally

opposed screws, and then return back to the rst two, repeating the process in order to evenly tighten the station

to ensure that the housing is fully seated on the gasket.

NOTE: Applying excessive torque may result in the brass threaded insert dislodging from the rear housing,

rendering the unit inoperable.

Federal Signal signaling.fedsig.com

Figure 3 Common Internal View

REMOVABLE

MOUNTING PLATE

WITH WIRING

HARNESS (2 X M4

SCREWS)

9 - POSITION

WIRING BLOCK

HOUSING

GROUND

UNLOOSEN FOUR

CAPTIVATED M4 SOCKET

HEAD CAP SCREWS

MODEL CP-PB

UNLOOSEN FOUR

CAPTIVATED M4 SOCKET

HEAD CAP SCREWS

MODEL CP-BG

Mounting the Call Point Station

ATTACH THE STATION SECURELY: To prevent injury, this apparatus must be securely attached to the mounting surface

in accordance with the installation instructions and local jurisdictions and codes. Use installer-supplied fasteners

suitable for the mounting surface.

All models of the Call Point station have the same rear chamber access to four corner oval-shaped holes for mounting

the station to a rigid vertical wall surface. The devices may be mounted by using four M6 metric threaded fasteners or

four 1/4-inch or #12 threaded fasteners that are installer-supplied. Be sure to follow all national and local jurisdictions

and codes as to placement of the station within the appropriate environment.

Figure 4 Mounting Layout

3.622"/ 92mm

3.542"/ 90mm

2.834"/

72mm

8Federal Signal signaling.fedsig.com

SAFETY MESSAGES TO INSTALLING AND WIRING : Products should be installed by a licensed electrician and

follow all safety instructions. Failure to do so may result in property damage, serious injury, or death. When installing

and operating the stations, the relevant national regulations for installation and operation (e.g., EN60079-14, IEC Wiring

Regulations, and NEC/CEC) along with any additional national and local codes/requirements must be observed.

• To avoid electrical shock hazards, do not connect wires when power is applied. Failure to observe this warning may

lead to serious injury or death.

• Painting and surface nishes, other than those applied by Federal Signal Corporation, are not permitted.

• Wiring terminations should be in accordance with specications within this manual and required by national

and local requirements, depending on the application. Federal Signal recommends that all wiring leads be fully

identied.

• In all countries, the wiring must comply with all national and local codes and standards.

• Ensure that all hardware connections are secure. Stainless steel fasteners must be used in corrosive environment

applications mounting the station to a rigid surface.

• Ensure that all cable glands and stopping plugs are certied with a suitable sealing washer/o-ring to ensure the

NEMA/IP rating of the station.

• The internal earth ground terminal must be used for equipment grounding where and when required.

Internal Rear Chamber Wiring

SHOCK HAZARD: To avoid electrical shock hazards, do not connect wires when power is applied. Failure to observe

this warning may lead to serious injury or death.

All Federal Signal Call Points stations are supplied with a standard nine-position wiring block mounted to a removable

aluminum bracket for ease of wiring if desired. Multiple factory pre-terminated wiring layouts are available, depending on

the options that the station will have installed:

Figure 5 Internal rear chamber wiring

2 x M4 CAPTIVATED SCREWS -

LOOSEN TO REMOVE REAR HOUSING

TERMINAL PLATE FOR WIRING EASE

WIRED TO

FRONT

HOUSING

ASSEMBLY

FACTORY INSTALLED CASE

CLAMP WIRING BLOCK OPTION

• Wire gauge range is 0.5 to 4.0 mm, (12-20 AWG) for either solid or stranded conductors.

• Strip length of 9 - 10 mm (0.35 – 0.39 inch)

There are two factory-installed wiring alternatives to the Federal Signal Call Points stations: a factory-installed case

clamp wiring block or a screw-down terminal block mounted to the removable aluminum bracket.

Federal Signal signaling.fedsig.com

Figure 6 Block wiring option

FACTORY INSTALLED TERMINAL BLOCK WIRING

• Wire gauge range is 0.5 to 4.0 mm, (12-22 AWG) for either solid or stranded conductors.

• Strip length of 8 mm (0.315 inch)

For both available wiring congurations:

• The cross-sectional area of the primary earth (ground located within the rear housing) must equal the cross-

sectional area of the phase conductor.

• The incoming wire must be rated per the corresponding national and local codes in which the station is used.

Tools needed (after internal access):

• Wire stripper

• 4.0 x 0.8 mm or 1/8” slotted screwdriver

To wire the CP-PB (pushbutton) and CP-BG (break glass) models:

1. If desired for easier access, loosen the two captivated M4 Philips screws on the aluminum mounting bracket and

remove it from the rear housing, taking care, as it still remains directly wired to the front housing assembly.

2. Strip the incoming wiring leads to the station to the appropriate length as noted above (depending on wiring block

conguration).

NOTE: Ensure that the incoming lead lengths into the station meet the required national and local regulations/

codes and also that the leads are not excessive in length causing the station not to be reassembled.

Figure 7 Factory test wires

REMOVE AND

DISCARD

FACTORY TEST

WIRE LEADS AS

NOTED BY TAG.

(2, 3, OR 6 WIRES)

3. Remove the 22 AWG factory test leads (as noted by tag around them) from the terminal wiring block and discard

them.

4. Reference the following wiring schematic diagrams for your station and its application within your system. Wire

per the diagram shown.

5. Ensure that all wires are properly seated and restrained to the station’s wiring or terminal block.

10 Federal Signal signaling.fedsig.com

6. Route/tuck in the wiring into the rear housing of the unit and carefully reassemble the unit’s front and rear

housings so that both fully seat to each other when the four M4 screws are tightened. Alternate between

tightening the diagonal pairs of screws to ensure that the station’s housings are tightened evenly.

Standard SPDT and DPDT Devices Switch Wiring

For the standard-issue SPDT and optional DPDT models, please note the following applicable requirements for these

specic models:

• A factory-installed jumper is supplied across input terminals 7 and 8 of the single pull double throw switch device;

on a double pull double throw device, input terminals 6, 7, and 8 are used as secondary inputs with common.

Figure 8 Standard SPDT switch wiring Figure 9 Standard DPDT switch wiring

Optional EOL, Diode, and Series Resistor Module Install and Wiring, SPDT and DPDT devices:

For the SPDT and DPDT models with optional eld installed EOL or Series Resistor Module(s), please note the following

applicable requirements for these specic models:

• When using with a re alarm control panel, the panel is to be limited to 5 A maximum. An LED, EOL, or series

resistor may require a compatible control panel.

• The separately supplied EOL and Series Resistor (as well as Diode) modules are installed via snap-t clips into two

possible locations on the rear mounting plate for wiring ease and replaceability:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Sicherheitssystem Handbücher

Federal Signal Corporation

Federal Signal Corporation WV450XL Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation e-Q2B Handbuch

Federal Signal Corporation

Federal Signal Corporation SST-MV Handbuch

Federal Signal Corporation

Federal Signal Corporation PAGASYS GEN II P-SYS-G Betriebsanleitung

Federal Signal Corporation

Federal Signal Corporation SSTX3-MV Handbuch

Federal Signal Corporation

Federal Signal Corporation SelecTone 300SCW-1 Handbuch

Federal Signal Corporation

Federal Signal Corporation PA4000 Handbuch

Federal Signal Corporation

Federal Signal Corporation VISION Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation PSCE-R Handbuch

Federal Signal Corporation

Federal Signal Corporation 2-120 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371ST-250 Handbuch

Federal Signal Corporation

Federal Signal Corporation G-LED Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SMART VECTOR SL Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SmartSiren Platinum SSP3000B Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SLMBS Series Benutzerhandbuch

Federal Signal Corporation

Federal Signal Corporation PA4000 Handbuch

Federal Signal Corporation

Federal Signal Corporation SST3-MV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 400HMK-AC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Solaris LP800 Handbuch

Federal Signal Corporation

Federal Signal Corporation Personnel Alerting System Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Split Vision VSLR3 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Premium Vision Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation PA300 Series 690009 Handbuch

Federal Signal Corporation

Federal Signal Corporation CommCenter D1 Series Handbuch

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung