Federal Signal Corporation WV450XL Series Bedienungsanleitung

25500104A

Rev. A0 1113

Printed in U.S.A.

Model WV450XL Series

GRP LED Beacon

for Use in Hazardous and Marine Locations

Installation and

Maintenance Instructions

*magenta and yellow not shown

Warranty – Seller warrants all goods for ve years on parts and 2-1/2 years

on labor, under the following conditions and exceptions: Seller warrants that

all goods of Seller's manufacture will conform to any descriptions thereof

for specications which are expressly made a part of this sales contract and

at the time of sale by Seller such goods shall be commercially free from

defects in material or workmanship. Seller reserves the right at the Seller’s

discretion to “Repair and Return” or “Replace” any item deemed defective

during the warranty period. This warranty does not cover travel expenses,

the cost of specialized equipment for gaining access to the product, or labor

charges for removal and reinstallation of the product. This warranty shall be

ineffective and shall not apply to goods that have been subjected to misuse,

neglect, accident, damage, improper maintenance, or to goods altered or

repaired by anyone other than Seller or its authorized representative, or if

ve years have elapsed from the date of shipment of the goods by Seller with

the following exceptions: lamps and strobe tubes are not covered under this

warranty. Outdoor warning sirens and controllers manufactured by Federal

Warning Systems are warranteed for two years on parts and one year on labor.

No agent, employee, representative or distributor of Seller has any authority

to bind the Seller to any representation, afrmation, or warranty concerning

the goods and any such representation, afrmation or warranty shall not be

deemed to have become a part of the basics of the sales contract and shall

be unenforceable. THE FOREGOING WARRANTIES ARE EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES OR MERCHANTABILITY,

FITNESS FOR PURPOSE AND OF ANY OTHER TYPE, WHETHER

EXPRESS OR IMPLIED. These warranties shall not apply unless Seller

shall be given reasonable opportunity to investigate all claims for allegedly

defective goods. Upon Seller's instruction a sample only of allegedly defective

goods shall be returned to Seller for its inspection and approval. The basis of

all claims for alleged defects in the goods not discoverable upon reasonable

inspection thereof pursuant to paragraph 8 hereof must be fully explained

in writing and received by Seller within thirty days after Buyer learns of the

defect or such claim shall be deemed waived.

Industrial Systems

2645 Federal Signal Drive • University Park, IL 60484-3167

Tel: 708-534-4756 • 877-289-3246 • Fax: 708-534-4852

Email: [email protected] • www.federalsignal-indust.com • www.fs-isys.com

Model WV450XL Series

Contents

Safety Messages to Installers and Users............................................. 5

Overview of Model WV450XL Series .................................................... 6

Certication............................................................................................. 7

Unpacking the Beacon .......................................................................... 8

Mounting the Beacon............................................................................. 8

Safety Messages for Wiring................................................................... 9

Wiring the WV450XLD Flameproof Models........................................ 10

Wiring the 24 Vdc Model WV450XLD ............................................11

Wiring the 110-220 Vac Model WV450XLD .................................. 12

Wiring the WV450XLE Increased Safety Models ............................... 13

Wiring the 24 Vdc Model WV450XLE ........................................... 15

Wiring the 110-220 Vac Model WV450XLE ................................... 16

Changing the Flash Pattern................................................................. 16

Safety Messages to Maintenance Personnel..................................... 19

Maintaining the Beacon ....................................................................... 20

Cleaning the Enclosure .................................................................... 20

Replacing the LED Array ................................................................. 21

Ordering Accessories and Replacement Parts ................................. 23

Model WV450XL Series

Contents

Tables

Table 1 SW1 settings for ash patterns ................................................ 18

Table 2 Replacement parts ................................................................... 23

Figures

Figure 1 Mounting hole locations Ex d version ....................................... 8

Figure 2 Mounting hole locations Ex de version ..................................... 9

Figure 3 Connections for 24 Vdc model ............................................... 11

Figure 4 Connections for for 110-220 Vac model ................................. 13

Figure 5 Terminal block for Model 450XLE ........................................... 14

Figure 6 Connections Ex de DC or AC beacons................................... 15

Figure 7 Location of DIP switch for ash patterns ................................ 18

Installation and Maintenance Instructions

Model WV450XL Series

Safety Messages to Installers and Users

It is important to follow all instructions shipped with this product.

This device is to be installed by a trained electrician who is

thoroughly familiar with and will follow all applicable national and

local codes in the country of use.

This device should be considered a part of the warning system and not

the entire warning system.

The selection of the mounting location for the device, its controls and

the routing of the wiring are to be accomplished under the direction

of the facilities engineer and the safety engineer. In addition, listed

below are some other important safety instructions and precautions

you should follow:

• Read and understand all instructions before installing or operating

this equipment.

• The circuitry of the beacon can be damaged by an electrostatic

discharge. Follow antistatic procedures while installing the

beacon.

• Never alter the unit in any manner. Safety in hazardous locations

may be endangered if additional openings or other alterations are

made in units specically designed for use in these locations.

• Do not connect this beacon to the system when power is on.

• After installation, ensure that all threaded joints are properly

tightened.

• Keep the unit tightly closed when in operation.

• After installation, test the beacon system to ensure that it is

operating properly.

• After testing is complete, provide a copy of this instruction sheet

to all personnel.

• Establish a procedure to routinely check the beacon system for

proper activation and operation.

Installation and Maintenance Instructions

Model WV450XL Series

Failure to follow all safety precautions and instructions may result in

property damage, serious injury, or death.

Overview of Model WV450XL Series

The Federal Signal Model WV450XL Series is ideally suited for

explosive atmospheres and harsh environments. It is designed to serve

the demanding needs of offshore marine and land based industrial

applications. The housing is made of corrosion resistant components,

which dramatically reduces the cost of long-term maintenance.

The WV450XL Series beacons use all of the latest techniques in

non-metallic housing construction. The body of the product is

glass reinforced polyester (GRP) and 316 stainless steel hardware.

The use of GRP in the design improves corrosion resistance and

reduces weight as compared to traditional metal housings. The GRP

construction also saves time and money over the life of the product by

reducing or, in most cases, completely eliminating the need to perform

regular eld inspections of the ame path.

The WV450XL Series comes standard with metric entries, a 316

stainless steel dome guard and an extended life LED emitter.

The ameproof “D” versions come standard with a 316 stainless

steel mounting brackets and two M20 entries for eld cable gland

connections. The increased safety “E” versions have the added feature

of a terminal chamber with three M20 entries. The increased safety

design allows for quick eld termination and pass-through wiring.

There are seven dome colors: amber, blue, clear, green, magenta, red,

and yellow.

Product features:

• 316 stainless steel mounting bracket included

• Available voltages: 24 Vdc and 110-220 Vac

• Eight selectable ash patterns (Table 1 on page 18)

• Corrosion resistant GRP (glass reinforced polyester) housing

• Included dome guard

Installation and Maintenance Instructions

Model WV450XL Series

• M20 entries standard

• Body color natural black

• IP66 rated

• Zone 1 rated, IECEx, ATEX, Ex d IIB +H2 T6 Gb, Ex de IIB +H2

T6 Gb

Certication

Certicate Nos.: ATEX Cert No.: UL DEMKO 06 ATEX04259693X

IECEx Cert No.: IECEx UL 06.0010X

ATEX coding: II 2

Protection: Ex d IIB+H2 T6 Gb [-55°C ≤Ta≤ 55°C]

Ex de IIB+H2 T6 Gb [-20°C ≤Ta≤ 55°C]

Standards: EN60079-0: 2012, EN60079-1: 2007, EN60079-7: 2007.

IEC60079-0: 5th Ed., IEC 60079-1 6th Ed., IEC 60079-7:

4th Ed.

Special Conditions for Safe Use:

1) Potential electric static charging hazard. Use only a water

dampened cloth when cleaning the exterior of the unit.

2) The capacitance value of unearthed metal parts is 10 pF, when

measured per IEC/EN 60079-0.

3) Contact the manufacturer for information on the dimension of the

ameproof joints.

Condições especiais para o uso seguro:

1) Perigo de potencial carga eletroestática. Ao limpar a parte

externa da unidade, utilize apenas um pano úmido.

2) O valor de capacitância de peças metálicas desenterradas é

10 pF, quando medido por IEC / EN 60079-0.

3) Contate o fabricante para obter informação sobre a dimensão

das juntas à prova de fogo.

Installation and Maintenance Instructions

Model WV450XL Series

Unpacking the Beacon

EXPLOSION HAZARD—Damaged dome covers can lead to

explosions that could result in serious injury or death. Replace

damaged dome covers.

After unpacking the beacon, examine it for damage that may have

occurred in transit. If it has been damaged, do not attempt to install or

operate it. File a claim immediately with the carrier, stating the extent

of the damage. Carefully check all envelopes, shipping labels, and tags

before removing or discarding them. Disposal of all shipping materials

must be carried out in accordance with national and local codes and

standards. If any parts are missing, please call Federal Signal Customer

Support at +1 708-534-4756 or +1 877-289-3246.

Mounting the Beacon

SECURE TO FLOOR OR WALL—To prevent injury, this apparatus

must be securely attached to the oor or wall in accordance with

the installation instructions.

Figure 1 Mounting hole locations Ex d version

M20 GLAND ENTRY

2 POSITIONS

63.5 [2.50]

ø39.4 [ø1.55] X 2

41.3 [1.63]

136.5 [5.37]

114.3 [4.50]

57.2 [2.25]

12.7 [0.50] 41.3 [1.63]

82.6 [3.25]

289.7 [11.41] 113.3 [4.46]

Ex d VERSION

GUARD LENS COVER ASSY

GRUB SCREW

Installation and Maintenance Instructions

Model WV450XL Series

Figure 2 Mounting hole locations Ex de version

290A7613

Ex de VERSION

ø8.9 [ø0.35] X 3

MOUNTING HOLES

97.1 [3.82]

57.4 [2.26]

M20 GLAND ENTRIES

3 POSITIONS

CERTIFICATION LABEL WARNING LABEL

EExde COVER SCREWS

See Figures 1 and 2. The Federal Signal WV450XL Series LED

beacon is mounted using a mounting bracket xed to the base of

the unit. Install the enclosure on the selected support surface using

the three 9.0 mm (0.35 in) mounting holes. Use installer-supplied

fasteners suitable for the surface to which the device will be mounted.

Safety Messages for Wiring

When installing and operating explosion-proof electrical equipment,

the relevant national regulations for installation and operation (e.g.,

EN60079-14 and IEC Wiring Regulations) must be observed.

• To maintain the explosion-proof integrity of the enclosure,

DO NOT damage the dome or threads while disassembling or

reassembling unit.

• Painting and surface nishes, other than those applied by Federal

Signal Corporation are not permitted.

• Cable termination should be in accordance with specications

applying to the application. Federal Signal recommends that all

cables and cores should be fully identied.

• Ensure that only the correct component certied glands are used

and that the assembly is shrouded and correctly earthed. Gland

entries are M20-1.5 6H. Supply wires to be rated 85 °C minimum.

Installation and Maintenance Instructions

Model WV450XL Series

• Certique-se de utilizar apenas as juntas componentes

certicadas corretas e de que o equipamento instalado esteja

blindado e devidamente conectado à terra. As entradas das juntas

são de M20-1,5 6 H. Os cabos de alimentação são certicados

para temperatura mínima de 85 °C.

• Ensure there is not too much slack of cable cores within the unit,

due to space limitations.

• Ensure that only the supplied stopping plugs are used to blank

off unused gland entry points. Failure to do so may negate the IP

rating on the unit.

• In all countries, the wiring must comply with all national and

local codes and standards.

• Ensure that all nuts, bolts and xings are secure.

Wiring the WV450XLD Flameproof Models

SHOCK HAZARD—To avoid electrical shock hazards, do not

connect wires when power is applied.

This section has wiring instructions for the two ameproof models:

• WV450XLD 24 Vdc

• WV450XLD 110-220 Vac

The maximum wire gauge is 2.5 mm2 (12 AWG). The wire must be

rated 85 °C or higher. Use only stranded or multiple strand cable to

terminate the beacon.

Cable termination for these models should be in accordance with

specications applying to the application. It is recommended that all

cables and cores should be fully identied. Use the appropriate cable

gland for the application. Gland entry threads are M20-1.5 x 6H.

Inhaltsverzeichnis

Andere Federal Signal Corporation Sicherheitssystem Handbücher

Federal Signal Corporation

Federal Signal Corporation e-Q2B Handbuch

Federal Signal Corporation

Federal Signal Corporation SelecTone 300SCW-1 Handbuch

Federal Signal Corporation

Federal Signal Corporation Commander 371ST-250 Handbuch

Federal Signal Corporation

Federal Signal Corporation SLMBS Series Benutzerhandbuch

Federal Signal Corporation

Federal Signal Corporation UltraVoice Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SmartSiren Platinum SSP3000B Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SMART VECTOR SL Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Premium Vision Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation CP-PB Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CommCenter D1 Series Handbuch

Federal Signal Corporation

Federal Signal Corporation SST-MV Handbuch

Federal Signal Corporation

Federal Signal Corporation 2001SRNB Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 400HMK-AC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISION Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation PA4000 Handbuch

Federal Signal Corporation

Federal Signal Corporation 2-120 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Fireball FB2LEDX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISION Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Smart Siren Handbuch

Federal Signal Corporation

Federal Signal Corporation 400 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation PAGASYS GEN II P-SYS-G Betriebsanleitung

Federal Signal Corporation

Federal Signal Corporation PSCE-R Handbuch

Federal Signal Corporation

Federal Signal Corporation Pathway Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung