Fermax NEO MEET Benutzerhandbuch
NEO MEET
INSTALLER MANUAL
2NEO MEET INSTALLER MANUAL
Code 970200Ib V11_20
CONGRATULATIONS FOR BUYING A QUALITY PRODUCT!
Fermax Electrónica develops and manufactures premium equipment
that meets the highest design and technology standards. We hope you
will enjoy all its functions.
Technical publication for information purposes edited by FERMAX ELECTRÓNICA S.A.U.
FERMAX ELECTRÓNICA applies a continuous improvement policy, therefore it reserves the right to modify the contents of
this document, as well as the product features hereof at any time and without prior notice. Any modication will be reected
in subsequent editions of this document.
This product is protected with the following patents and utility models:
PATENTS: US 9215410, US 9762852, BE1023440, AU2014203706.
UTILITY MODELS: ES1187384U, ES1141495U, FR3038192, DE202016000632U1, CN205987229(U).
3
NEO MEET INSTALLER MANUA
4. LOCAL PROGRAMMING FROM THE MONITOR 9
4.1. Installer access 9
4.2. Basic conguration of the MONITOR 10
4.3. Conguring the alarm settings 11
4.4. Enable/disable FUNCTIONS 12
4.5. Enable/disable function ICONS on the monitor 13
4.6. Change INSTALLER PIN 14
5. WEB BROWSER PROGRAMMING 15
5.1. Device 16
5.2. General 16
5.3. Network conguration 17
5.4. Ip Camera 17
5.5. SIP 18
5.6. Advanced 19
5.7. Actuators 20
5.8. PIN Code 21
5.9. Restore 21
2. INSTALLATION 5
2.1. Stand placement 5
2.2. Attaching the monitor to the stand 5
2.3. Connection diagram 6
2.4. Wired alarm and doorbell sensors 6
2.5. Wiring of FERMAX MEET Relay Module Ref. 1616 7
INDEX
6. ANNEX 22
6.1. Firmware updates 22
7. REGULATIONS AND CERTIFICATION 23
3. TECHNICAL SPECIFICATIONS 8
1. DESCRIPTION 4
4NEO MEET INSTALLER MANUAL
1 DESCRIPTION
The following document is the Installation Manual for the NEO 7” MEET monitor, with
rmware V03.00.
Alarm mode
LAN status
Missed calls
Eceived messages
Do not disturb
Date and time
5
NEO MEET INSTALLER MANUA
2 INSTALLATION
2.1. STAND PLACEMENT
Before installing the MEET monitor, the corresponding installation stand must be placed
on the wall.
This stand must be screwed on covering the box or conduit where the cable or cables
connecting to the monitor (ethernet cable, power supply and accessories, if any) arrive.
Use the screws and plugs supplied with the monitor to attach the stand.
2.2. ATTACHING THE MONITOR TO THE STAND
Once the stand is in place, proceed to hang the monitor.
To do this, snap the 4 connector anchors into the corresponding slots on the back of the
monitor and push down on the monitor to attach it.
Do not forget to pre-connect the ethernet network connectors, power supply and
accessories, if applicable.
6NEO MEET INSTALLER MANUAL
2.3. CONNECTION DIAGRAM
2.4. WIRED ALARM AND DOORBELL SENSORS
The MEET monitor are connected to the installation by means of connectors: ethernet
for LAN connection and MOLEX type connectors for other connections (power supply,
RS-485 and sensor inputs).
A bag containing the corresponding male connectors with their cables is enclosed with
the wall connector Ref.9541
iring diagram, normally open sensor.
Wiring diagram, normally closed sensor.
Wiring diagram, normally open sensor, option 3C.
LAN: Ethernet connector to the building’s LAN PoE installation.
+12V: 12 Vdc power input for non-PoE installations.
Siren / Sensors:
o S: 12 Vdc auxiliary output synchronised with the activation of any sensor.
The maximum current is 100 mA.
o -: GND.
o Z1-Z7: sensor inputs. (Z8 is already used for tamper alarm)
12V +, -, 485+, 485-: Salida alimentación y conexión RS-485 para el Módulo de 10
Relés Ref. 1616.
NEO 7” CONNECTIONS
7
NEO MEET INSTALLER MANUA
To activate the devices to be controlled, use the relay outputs 1 to 8, corresponding to the
activations R1 to R8 of the monitor control screen. Relay outputs 0 and 9 are not used.
The module Ref. 1616 is powered directly from the monitor. No additional power is required.
The address of module has to be No.1 (this is the factory value).
NOTES
The module Ref. 1616 only activates the corresponding relay during the time indicated in the
programming (between 1 and 60 seconds). After this time, the relay automatically returns to
standby.
No relay status is displayed on the monitor.
2.5. WIRING OF FERMAX MEET RELAY MODULE REF. 1616
To use the actuator control function, a FERMAX MEET Relay Decoder Ref. 1616 must
be installed.
The connection to the monitor is through the RS-485 connector as shown in the following diagram.
Wiring diagram, normally closed sensor, option 3C.
Wiring diagram, doorbell.
NOTE:
Option 3C consists of a monitoring system via which the monitor would detect sabotage
in the sensor loop (shorting or cutting the sensor loop).
To enable this option, connect a 2.2KOhm resistor according to the diagram and enable
the 3C function in the monitor (See section 4.3 Alarm settings). A bag with 8 resistors is
included with the wall connector.
Triggering any sensor activates the S output for 5 minutes if the monitor has not been
disarmed, except when congured as a doorbell.
The Z8 sensor input is reserved for the internal tamper (monitor anti-sabotage).
8NEO MEET INSTALLER MANUAL
TECHNICAL SPECIFICATIONS
Dimensions (mm) 203 (Ancho) × 129 (Alto) ×
17.5 (Profundidad)
Power supply 12 Vdc o PoE
Current
Idle current 200 mA
Working current 500 mA
Resolution 800x480 pixels
Touch screen Tecnología capacitiva
Tiempo máximo
Conversation time 120 secs.
Time to answer the call 35 secs.
Auto-on time 30 secs.
Maximum recording log 64
Maximum number of IP cameras 8
Block 001-999
Apartment 0001-9899
Working temperature -10ºC R55º C
Relative humidity 20-85% (without condensation)
9
NEO MEET INSTALLER MANUA
4 LOCAL PROGRAMMING FROM THE MONITOR
MEET monitors allow the programming of basic conguration parameters (block
identication, housing, IP address, etc.) through their own interface and without using a
PC, so that it is possible to leave it ready to complete its conguration later via the web
browser.
All MEET monitors have the same default IP address (10.1.1.1). In order to access them
remotely via web browser, it is necessary to assign them a unique IP address, according
to the requirements of the LAN.
It is therefore necessary to carry out prior planning of the installation, with the IP address
to be assigned to each and every one of the components of the installation (monitors,
panels and guard units).
The default INSTALLER PIN is 6666.
It can be changed later for another of your choice.
For security reasons, if the wrong PIN is entered three times in a row, the device will be
blocked for 60 seconds.
Once the correct PIN has been entered, the INSTALLATION SETTINGS options will
appear:
4.1. INSTALLER ACCESS
From the idle screen, access the installer section by touching the icon .
Touch the icon to access the programming parameters through the interface of the
monitor itself.
Identify yourself by entering the INSTALLER PIN through the keypad:
10 NEO MEET INSTALLER MANUAL
Enable/disable user functions.
Conguring the built-in alarm settings.
Change the INSTALLER PIN code.
Installation/desinstallation of ICON user functions.
Basic monitor conguration (IP addressing, LAN
conguration, block, housing, etc.)
The options available from this section are:
4.2. BASIC CONFIGURATION OF THE MONITOR
Touch the icon to access the basic conguration parameters:
Use the keyboard that will appear on the screen to enter the corresponding programming
parameters.
MONITOR SETTINGS
• BLOCK: Block number of the apartment where the monitor is installed.
• APARTMENT: Number of the apartment where the monitor is installed.
• MONITOR: Number (from 0 to 9) assigned to each of the monitors installed in the
same apartment, in the case that there are more than one. Otherwise, leave the
default value “0”.
• SYNC CODE: Synchronisation code with the rest of the devices in the apartment.
Default value is 123456.
• SOFTWARE IP: IP address of the PC where the MEET Management Software is
installed (if any).
• SW PIN: MEET Management SoftwareACCESS PIN code. The default option is 123456.
Andere Handbücher für NEO MEET
1
Inhaltsverzeichnis
Andere Fermax Monitor Handbücher
Fermax
Fermax VEO Bedienungsanleitung
Fermax
Fermax SMILE 7" Monitor Bedienungsanleitung
Fermax
Fermax VEO XS Bedienungsanleitung
Fermax
Fermax DUOX PLUS VEO-XL Bedienungsanleitung
Fermax
Fermax MEET NEO 7 Benutzerhandbuch
Fermax
Fermax VEO DUOX Bedienungsanleitung
Fermax
Fermax DUOX PLUS WIFI VEO XS MONITOR Bedienungsanleitung
Fermax
Fermax VEO XS DUOX Bedienungsanleitung
Fermax
Fermax MEET MIO Series Benutzerhandbuch
Fermax
Fermax FERMVISION Benutzerhandbuch
Fermax
Fermax iLOFT 4+N Bedienungsanleitung
Fermax
Fermax VEO XS DUOX Benutzerhandbuch
Fermax
Fermax VEO DUOX Bedienungsanleitung
Fermax
Fermax LYNX SMILE Benutzerhandbuch
Fermax
Fermax LOFT COMPACT VDS Bedienungsanleitung
Fermax
Fermax VEO XS DUOX Benutzerhandbuch
Fermax
Fermax F9445 Benutzerhandbuch
Fermax
Fermax BUS 3 CITYMAX Bedienungsanleitung
Fermax
Fermax DUOX iLOFT Leitfaden
Fermax
Fermax DUOX PLUS SKYLINE Bedienungsanleitung
