Festo DNCKE Bedienungsanleitung

en Operating

instructions

8074345

2017-10b

[8074347]

Cylinder with clamping unit / Clamping unit

DNCKE/KEC

2 Festo – DNCKE/KEC – 2017-10b

Original instructions

Symbols: The clamping unit KEC or the cylinder with clam

ping unit DNCKE is designated a product or cy

linder in these operating instructions.

Installation and commissioning may only be per

formed in accordance with these instructions by

technicians with appropriate qualifications.

Warning

Caution

Note

Environment

Accessories

English 3.........................................................................

DNCKE/KEC

Festo – DNCKE/KEC – 2017-10b English 3

English – Cylinder with clamping unit / Clamping unit

DNCKE/KEC

Table of contents

1 Configuration 5............................................................

2 Safety 6..................................................................

2.1 Intended use 6.............................................................

2.2 Foreseeable misuse 6.......................................................

2.3 General safety information 7..................................................

2.4 Mounting and connecting 7...................................................

2.5 Qualification of specialized personnel 7.........................................

3 Function 8................................................................

4 Transport 8...............................................................

5 Installation 8..............................................................

5.1 Mechanical installation 8.....................................................

5.1.1 Mounting the clamping unit 9.........................................

5.1.2 Mounting attachments 10.............................................

5.1.3 Mounting accessories 11.............................................

5.2 Pneumatic installation 11.....................................................

5.2.1 Prerequisites 11....................................................

5.2.2 Functional tests 12..................................................

5.2.3 Creating a tubing connection to the clamping unit 12.......................

6 Commissioning 13...........................................................

6.1 Dismounting the round material (only required for KEC) 14...........................

6.2 Adjustment of the clamping unit 15..............................................

6.3 Test run 16.................................................................

6.4 Clamping force test 16........................................................

7 Operation 20...............................................................

7.1 Adjustment of the clamping unit 21..............................................

DNCKE/KEC

4 Festo – DNCKE/KEC – 2017-10b English

8 Maintenance and care 22.....................................................

9 Disassembly and repair 22....................................................

10 Disposal 22................................................................

11 Accessories 22..............................................................

12 Fault clearance 23...........................................................

13 Technical data 24............................................................

DNCKE/KEC

Festo – DNCKE/KEC – 2017-10b English 5

Documentation on the product

For all available product documentation èwww.festo.com/pk

1 Configuration

DNCKE KEC

7 23765

1Compressed air supply port for cylinders next

to the adjusting screws for the pneumatic

cushioning (only for DNCKE)

2Supply port for releasing the clamp

3Locking screw with internal hexagon socket

(for adjusting sleeve)

4Piston rod (only DNCKE)

5Adjusting sleeve with spanner flat

6Hollow bolt with thread for mounting

7Hole with filter element for exhausting the

clamping chamber

8Slots for proximity sensor (only DNCKE)

9Round material for transport protection

(only KEC)

Fig. 1

DNCKE/KEC

6 Festo – DNCKE/KEC – 2017-10b English

Definition

In these operating instructions, the designation

“clamping unit” is used for:

– the individual product KEC

– the design type DNCKE integrated in the

cylinder

In these operating instructions, the designation

“round material” is used for:

– the transport lock for KEC

– the piston rod for DNCKE

DNCKE

KEC

Fig. 2

2 Safety

2.1 Intended use

The clamping unit KEC is intended to serve both as an individual product and integrated into a DNC

cylinder (for cylinders with clamping unit DNCKE) for holding, clamping and inhibiting the movement of

round material.

2.2 Foreseeable misuse

The clamping unit is not intended as a brake. Use as a braking device (dynamic applications) does not

conform with the intended use.

The clamping unit is not suitable for positioning tasks or for transmitting torques and lateral forces. A

self-aligning rod coupler (è11 Accessories) can prevent the transmission of lateral forces and bending

moments.

DNCKE/KEC

Festo – DNCKE/KEC – 2017-10b English 7

2.3 General safety information

WARNING

Risk of injury! Uncontrolled movement. Piston rods can advance suddenly and unexpec

tedly, thereby causing injury to anybody who is in the positioning range.

 Make sure that nobody can place his/her hand in the positioning range of the payload.

 Make sure that no foreign objects are present in the positioning range of the payload.

 Do not modify the product in any way. Improper modifications impair its function and

present a safety risk.

 Observe legal regulations applicable to the destination.

 Only use the product if it is in its original status and in perfect working order.

 Use the product only within the defined values (è13 Technical data).

 Observe product labelling.

 Observe applicable documents.

 Take into consideration the ambient conditions at the location of use.

 Protect the product during storage and operation from the following:

– Wetness or moisture

– Corrosive coolant or other materials (e.g. ozone)

– UV radiation

– Oils, greases and grease-solvent vapours

– Grinding dust

– Glowing chips or sparks

2.4 Mounting and connecting

 Observe tightening torques. Unless otherwise specified, the tolerance is ±20 %.

2.5 Qualification of specialized personnel

Only qualified specialized personnel may install, commission, service or disassemble the clamping unit.

The specialized personnel must be familiar with the installation and operation of electrical and pneu

matic control systems.

DNCKE/KEC

8 Festo – DNCKE/KEC – 2017-10b English

3 Function

Pressurising with compressed air on the supply port 2(èFig. 1)

opens the internal clamping component through a pneumatically

driven release mechanism. The round material can then move freely.

Fig. 3

If the compressed air supply port is exhausted, a spring-loaded

mechanism generates the clamping force of the clamping compon

ent. That way, the round material is clamped.

Fig. 4

4 Transport

 Take product weight into account (è13 Technical data).

5 Installation

5.1 Mechanical installation

Prerequisites

Note

Lateral loads and bending moments exerted on the round material damage its function

and destroy the internal clamping component.

 Make sure that the loads are only exerted on the round material in the direction of

movement. The use of a self-aligning rod coupler (è11 Accessories) prevents later

al forces.

Note

Movement of the round material against the clamping forces leads to heavy wear on the

internal clamping element and the round material.

 Make sure that the holding force is never exceeded. Otherwise, unexpected move

ment may occur.

 Make sure that the clamping unit is installed as follows:

– Operating elements always accessible

– Product fixed in such a way that it is free from mechanical stress or bending

 Check if additional external safety measures (e.g. pawls or moveable bolts) are required.

 Select the installation type for the desired application.

Refer to the Festo catalogue for more mounting alternatives (èFig. 5) and required accessories.

DNCKE/KEC

Festo – DNCKE/KEC – 2017-10b English 9

5.1.1 Mounting the clamping unit

Interfaces for mounting components on the cover (examples)

with foot mounting HNC1) with flange mounting FNC1) with swivel mounting SNC1)

1) èwww.festo.com/catalogue

Fig. 5

DNCKE/KEC

10 Festo – DNCKE/KEC – 2017-10b English

Dimensions (èCatalogue specifications)1)

Clamping unit KEC Clamping unit (with cylinder) DNCKE

1) èwww.festo.com/catalogue

Fig. 6

Size DNCKE 40 63 100

KEC 16 20 25

L12) [mm] 178 208.5 287

ZJ+ (plus stroke length) [mm] 277 315 408

TG [mm] 38 56.5 89

E [mm] 54 80 126

Screw-in depth [mm] 9.5 … 15 12.5 … 14 14 … 17

Screw M6 (4x) M8 (4x) M10 (4x)

Tightening torque [Nm] 5 13 30

2) Dimension varies depending on setting of the adjusting screw.

Tab. 1

 Place the clamping unit in the intended position.

 Tighten screws evenly (tightening torques èTab. 1).

5.1.2 Mounting attachments

Mounting on the DNCKE

 Mount the attachment component on the piston rod.

The spanner flat aJ on the piston rod serves as a counter holder

for the lock nut. If necessary, secure the lock nut with a screw

locking agent.

Fig. 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Festo Controller Handbücher

Festo

Festo CMMO-ST Bedienungsanleitung

Festo

Festo CMMP-AS-C2-3A Bedienungsanleitung

Festo

Festo SEC-ST-48-6-P01 Bedienungs- und Montageanleitung

Festo

Festo YJKP Bedienungsanleitung

Festo

Festo CPX-AP-I-4IOL-M12 Bedienungsanleitung

Festo

Festo s CMMD-AS-C8-3A Leitfaden

Festo

Festo VEAB Bedienungsanleitung

Festo

Festo CMSX-...-C-U-F1 series Bedienungsanleitung

Festo

Festo 03-B Bedienungsanleitung

Festo

Festo VPPI D Series Montageanleitung

Festo

Festo VOFA-L26-T52-M Series Bedienungsanleitung

Festo

Festo SFC-LAC-IO Series Referenzhandbuch

Festo

Festo CECC-X-M1 series Bedienungs- und Montageanleitung

Festo

Festo 32 MPA Bedienungsanleitung

Festo

Festo CMMP-AS-***-M3 Series Bedienungsanleitung

Festo

Festo CPX-CMAX Bedienungs- und Montageanleitung

Festo

Festo DAPS-2880-8000 R F Series Betriebsanleitung

Festo

Festo CPX Montageanleitung

Festo

Festo CPX-FEC Stücklistenhandbuch

Festo

Festo CMMS-AS G2 Series Bedienungsanleitung

Festo

Festo CMMD-AS series Bedienungsanleitung

Festo

Festo CMMP-AS Series Referenzhandbuch

Festo

Festo SPC200 Series Bedienungsanleitung

Festo

Festo CMMP-AS-***-M3 Series Bedienungs- und Montageanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch