Festo EGSC-BS-KF Bedienungsanleitung

en Operating

instructions

8067130

2016-12

[8067132]

Mini slide

EGSC-BS-KF

2Festo – EGSC-BS-KF – 2016-12

Original instructions

Identification of hazards and instructions on how to prevent them:

Danger

Immediate dangers which can lead to death or serious injuries

Warning

Hazards that can cause death or serious injuries

Caution

Hazards that can cause minor injuries

Other symbols:

Note

Material damage or loss of function

Recommendations, tips, references to other documentation

Essential or useful accessories

Information on environmentally sound usage

Text designations:

 Activities that may be carried out in any order

1. Activities that should be carried out in the order stated

– General lists

èResult of an action/References to more detailed information

EGSC-BS-KF

Festo – EGSC-BS-KF – 2016-12 English 3

English – Mini slide EGSC-BS-KF

Table of contents

1 About this document 4......................................................

2 Safety 4..................................................................

2.1 Safety Instructions 4........................................................

2.2 Use for intended purpose 4...................................................

2.3 Training of specialized personnel 4.............................................

3 Further information 4.......................................................

4 Service 5.................................................................

5 Product overview 5.........................................................

5.1 Function 5.................................................................

5.2 Configuration 5............................................................

6 Transport 6...............................................................

7 Mounting 6...............................................................

7.1 Preparation 6..............................................................

7.2 Mounting 7................................................................

7.3 Attachment 8..............................................................

7.4 Mounting accessories 9......................................................

8 Commissioning 10...........................................................

9 Service 12.................................................................

10 Dismounting 12.............................................................

11 Disposal 12................................................................

12 Fault clearance 13...........................................................

13 Technical data 14............................................................

EGSC-BS-KF

4 Festo – EGSC-BS-KF – 2016-12 English

1 About this document

For all available product documentation èwww.festo.com/pk

The mini slide EGSC-BS-KF is designated as product in these operating instructions.

Read the operating instructions carefully before starting all work on the product.

2 Safety

2.1 Safety Instructions

 Observe product labelling.

 Before working on the product, switch off the power supply and secure it against being switched on

again.

 Store the product in a cool, dry, UV-protected and corrosion-protected environment. Ensure storage

times are short.

 Protect the product during operation from damaging influences.

Damaging influences, for example, include grinding dust, glowing chips or sparks.

 Observe tightening torques. Unless otherwise specified, the tolerance is ± 20 %.

2.2 Use for intended purpose

The mini slide is intended to be used for positioning payloads in

combination with tools or as a drive when external guides are used.

The mini slide is approved for the “Slide Operation” mode èFig. 1.

Fig. 1

2.3 Training of specialized personnel

Only qualified personnel may perform installation, commissioning, maintenance and disassembly of the

product. The qualified personnel must be familiar with installation and operation of electrical control

systems.

3 Further information

Accessories èwww.festo.com/catalogue.

EGSC-BS-KF

Festo – EGSC-BS-KF – 2016-12 English 5

4 Service

Contact your regional Festo contact person if you have technical questions:

èwww.festo.com.

5 Product overview

5.1 Function

A rotating ball screw converts the rotation of a motor into straight-line motion. As a result, the slide 5

moves backwards and forwards. The slide is ball bearing guided. The reference position of the carriage

can be determined using proximity sensors (è7.4 Mounting accessories) or by referencing a fixed stop

(retracted end position).

5.2 Configuration

1 234 5 6 7

1Drive hub

2Motor mounting kit interface

3Guide rail

4Venting hole with filter element

5Slide with ball bearing guide

6Thread/centring holes for attachment com

ponents

7Drill hole for accessories, at both ends

(e.g.,clamping unit)

8Thread for optional switch lug

9Slot for sensor bracket

aJ Slots for mounting

aA Profile housing

Fig. 2

EGSC-BS-KF

6 Festo – EGSC-BS-KF – 2016-12 English

6 Transport

Note

Unexpected movement of components. The mini slide is unbraked. Without input

torque, the slide is freely movable.

 Secure slide during transport.

 Take product weight into account è13 Technical data.

7 Mounting

7.1 Preparation

 Do not modify the screws and threaded pins.

Exception: immediate requirement for change in these operating instructions.

 Select the motor and motor attachment kit from the

Festocatalogue: èwww.festo.com/catalogue.

When using other motors, observe the limit values for forces,

torques and speeds è13 Technical data.

 When mounting the motor: Follow the assembly instructions for

the mounting attachment kit.

 Connect motor cables only after the mini slide is mounted.

Fig. 3

Note

The reference position is lost when the motor is dismantled (e.g. when turning the

motor around).

 Start the homing procedure è8 Commissioning.

Caution

In case of a vertical or slanted mounting position:

When de-energised, the slide can move or fall to the lower end position in an

uncontrolled manner. Injury due to impacts or pinching.

 Bring moving parts of the product into a safe end position or secure them against falling.

EGSC-BS-KF

Festo – EGSC-BS-KF – 2016-12 English 7

 Place the product in such a way that the operating elements can

be reached.

 Install product without tension or distortion.

 Fasten product to a mounting surface with flatness of 0.05 %

ofthe stoke length, but max. 0.5 mm.

For gantry applications, attention must also be paid to parallel

alignment or product heights in alignment of the axes.

For additional information, contact your local Festo Service.

Fig. 4

7.2 Mounting

Interfaces for mounting components

on the housing on the profile

with screws e.g., with profile mounting EAHF-L21)

1) Accessories èwww.festo.com/catalogue.

Fig. 5

 Select mounting components according to the hole pattern èwww.festo.com/catalogue.

 Mount the mounting components outside the positioning range to prevent collisions.

 Mount the mini slide.

 Tighten screws evenly.

Size 25 32 45 60

Screw (on housing) M3 M4 M5 M5

Max. screw-in depth D [mm] 68.5 7 8

Tightening torque [Nm] 1.4 3.4 3.2 3.2

Centring H71) [mm] @5 @7

1) Remove the rubber cover cap

Tab. 1

EGSC-BS-KF

8 Festo – EGSC-BS-KF – 2016-12 English

7.3 Attachment

Prerequisites

Note

A warped attachment component bends the slide

and shortens the service life of the guide.

 Use an attachment component with an even

surface.

Evenness: t = 0.01 mm

 Mount only to the mounting surface (B) èFig. 8.

Fig. 6

 Place the rated load in such a way that the break-down torque

resulting from the force (parallel to the axis of motion) and the

lever arm is kept as small as possible.

 Prevent collisions of the attachment element and the payload

with other attachments èFig. 7. Fig. 7

Mounting

 Fasten the attachment to the slide with screws and centring

sleeves. Observe the maximum screw-in depth D and tightening

torque èTab. 2 .

For attachment components with their own guide:

 Precisely adjust the additional guide and mini slide or use a

connection that enables a tolerance compensation. The guide

isnot overloaded in this manner.

Fig. 8

(B)

Size 25 32 45 60

Screw M3 M4 M5 M5

Max. screw-in depth D [mm] 4.5 568

Tightening torque [Nm] 1.5 2.7 5.1 6.5

Centring H7 [mm] @2 @4 @5 @7

Tab. 2

EGSC-BS-KF

Festo – EGSC-BS-KF – 2016-12 English 9

7.4 Mounting accessories

To protect the end positions against uncontrolled excess travel:

 Check the necessity of proximity sensors (hardware limit switches).

If proximity sensors are used as limit switches:

 Preferably use proximity sensors with normally closed contact function.

This protects against excess travel beyond the end position, if the proximity sensor cable is broken.

If proximity switches are used as reference switches:

 Use proximity sensors that correspond to the input of the control system being used.

Mounting of the proximity sensor

 Use the proximity sensor with the sensor bracket (A) in the

groove 9 èAssembly instructions of the accessories.

Fig. 9

(A)

Avoidance of contamination

 Connect sealing air. To do so, remove the filter element 4from

the housing and connect the compressed air/vacuum.

Fig. 10

EGSC-BS-KF

10 Festo – EGSC-BS-KF – 2016-12 English

8 Commissioning

Caution

Risk of injury due to unexpected movement of

components.

 Protect the positioning range from intervention.

 Keep foreign objects out of the positioning

range.

 Perform commissioning at low speed.

Fig. 11

Note

Incorrect set values for the braking ramp in STOP statuses (e.g. EMERGENCY OFF,

QuickStop) result in an overloading of the spindle axis and can destroy it or drastically

reduce its service life.

 Check the settings for all braking ramps in the controller or the higher-order control

system (deceleration values and jerk).

 Set delay values (braking delay, time delays) in such a way that the maximum driving

torque, acceleration or maximum feed force is not exceeded. In the process, take

the following into consideration:

– Travel speed

– Moving mass

– Mounting position

 Use the Festo “PositioningDrives” engineering software to design the spindle axis

èwww.festo.com.

Note

Block-shaped acceleration profiles (without jerk limitation) cause high peaks in the

drive force that can lead to an overloading of the drive. Due to overshooting effects,

positions outside of the permissible range may also occur. A jerk-limited acceleration

specification reduces vibrations in the entire system and has a positive effect on stress

in the mechanical system.

 Check the controller settings and adapt them if necessary (e.g., jerk limitation,

smoothing of the acceleration profile).

Andere Handbücher für EGSC-BS-KF

Inhaltsverzeichnis

Andere Festo Industrieanlagen Handbücher

Festo

Festo EAMM-A-D Series Montageanleitung

Festo

Festo ELGA-BS-KF Bedienungsanleitung

Festo

Festo ELGA-TB Stücklistenhandbuch

Festo

Festo CP Factory Bedienungsanleitung

Festo

Festo CPV10-EX-VI Bedienungsanleitung

Festo

Festo HGDD Bedienungsanleitung

Festo

Festo DHTG Bedienungsanleitung

Festo

Festo ADN Series Einrichtungshandbuch

Festo

Festo FBS-SUB-9-GS-IB-B Bedienungsanleitung

Festo

Festo ELGA-TB-G Bedienungsanleitung

Festo

Festo YSRWJ A Series Bedienungsanleitung

Festo

Festo Robotino 8029256 Bedienungsanleitung

Festo

Festo DADM-EP-G6 Bedienungsanleitung

Festo

Festo CPX-AP-I-4IOL-M12 Bedienungsanleitung

Festo

Festo VABD Series Bedienungsanleitung

Festo

Festo 696688 Bedienungsanleitung

Festo

Festo ELGC-TB-KF Stücklistenhandbuch

Festo

Festo EGSL Bedienungsanleitung

Festo

Festo MS6 Series Bedienungsanleitung

Festo

Festo DZF Einrichtungshandbuch

Festo

Festo CLR-12 Bedienungsanleitung

Festo

Festo CPX-FB6 Bedienungsanleitung

Festo

Festo KES-MC-1-SUB-9 Series Bedienungsanleitung

Festo

Festo EHPS Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung