Festo CPV-GE-ASI-8E6A-Z Series Stücklistenhandbuch

Brief description

CPV valve terminal

with AS-Interface

type

CPV10/14-ASI-8

E6A

– English

8101710

2018-11b

[8101712]

Compact performance

Festo CPV10/14-ASI-8E6A 2018-11b2

Translation of the original instructions

Documentation on the product

For all available product documentation

èwww.festo.com/pk

Festo AG & Co.

Ruiter Straße 82

73734 Esslingen

Germany

Internet: http://www.festo.com

E-Mail: service_international@festo.com

Reproduction, distribution or sale of this document or communication of

its contents to others without express authorization is prohibited.

a patent, utility model or design patent is registered.

English 3............................................

Festo CPV10/14-ASI-8E6A 2018-11b English 3

1 User instructionsEnglish

Valve terminal type CPV..-GE-ASI-8E6A-Z has been de

signed exclusively for controlling pneumatic actuators and

is intended for use in bus systems in accordance with the

AS-Interface specification 2.1. If additional commercially-

available components such as sensors and actuators are

connected, the specifiedlimits for pressures, tempera

tures, electrical data, torques, etc. must not be exceeded.

AS-Interface bus systems and valve terminals may only be

installed by personnel especially trained for this purpose.

Detailed information on the design and addressing of your

bus system can be found in the manual for your AS-Inter

face master.

Information on the pneumatic components of the valve ter

minal can be found in the Pneumatics manual P.BE-CPV-... .

Warning

SSwitch off the power supply before connecting or

disconnecting plugs (otherwise this could lead to

functional damage).

SConnect the earth connection on the left end plate

with low impedance (short cable with large cross-sec

tional area) to the earth potential.

SCommission only a valve terminal which has been

fitted and wired completely.

Festo CPV10/14-ASI-8E6A 2018-11b English4

2 Connecting and display elements

123 4 5

aJaB aA

1AS-Interface bus connection

2Earth/ground connection

3Type plate

4LED status display for inputs (green)

5Address selector button with LED

(red)

6Sensor connections (PNP)

7Inscription fields for addresses

8LED status display for

valves (yellow)

9Valve plates slave 2

aJ Valve plates slave 1

aA Load voltage connec

tion for valves

aB PWR LED (power,green),

Fault LED (fault, red)

PWR LED Fault LED Meaning

off

flashes

off

flashes

AS-Interface voltage applied, no fault

No AS-Interface voltage on the bus

AS-Interface address not set ( = 0)

Short circuit / overload at the inputs or

address selector switch actuated

Bus communication failed (watchdog expired)

Festo CPV10/14-ASI-8E6A 2018-11b English 5

3 Installation instructions

3.1 AS-Interface Addresses

Before connecting to the AS-Interface bus: assign an un

used address to each slave.

Please note

‒ The valve terminal type CPV..-GE-ASI-8E8A-Z contains

2 AS-Interface slaves. The valve terminal behaves on

the AS-Interface bus like two individual valve ter

minals each with 4 inputs and 3 outputs (valve sole

noid coils).

Assignment of the inputs and outputs (valves):

– Slave 1: Inputs I0...I3; outputs O0...O2

– Slave 2: Inputs I4...I7; outputs O4...O6.

‒ Automatic addressing with the function “Automatic

address assignment” of the master is not possible.

‒ It is not necessary to parametrize the AS-Interface

slave.

Address assignment

The assignment of the data bits to the inputs and outputs

of the slave shows the following figure:

Slave 1: IO code 7HSlave 2: IO code 7H

D0 D1 D2 D3

I/O I/O I/O I/O

I0 I1 I2 I3

O0 O1 O2 –

Inputs:

Outputs:

Data bits: D0 D1 D2 D3

I/O I/O I/O I/O

I4 I5 I6 I7

O4 O5 O6 –

E/A = bi directional (B)

The address mapping depends on the configuration of the

master.

Festo CPV10/14-ASI-8E6A 2018-11b English6

3.2 Assigning the AS-Interface addresses

Please note

Addressing valve terminal type CPV..-GE-ASI-8E6A-Z is

only permitted with addressers as per specification 2.1.

Other addressers do not permit clear access to the

slaves and in some cases overwrite the ID1 codes.

Recommendation: Use the Festo addresser type ASI-PRG-

ADR with adapter cable type KASI-ADR.

Factory setting: Slave 1: address #1, A slave

Slave 2: address #1, B slave

The addressing device scans the existing slaves in the

AS-Interface network.

SAssign the desired addresses to the two slaves one

after the other.

Operation with AS-Interface masters < Spec. 2.1

Operation with AS-Interface masters < Spec. 2.1 is possible

but both slaves must be programmed as A slave.

Recommendation: For operation with AS-Interface masters

< Spec. 2.1 use valve terminal type CPV..-GE-ASI-8E8A-Z

instead of CPV..-GE-ASI-8E6A-Z.

Festo CPV10/14-ASI-8E6A 2018-11b English 7

Address selector button

If the same address is assigned to both slaves, no clear

access to the slaves is possible.

In this case slave 1 can be disconnected from the AS-Inter

face bus with the aid the address selector button. You can

unlock the pushbutton by pressing it. Slave 1 will then be

disconnected from the AS-Interface bus. If the AS-Inter

face bus voltage is applied, the address selector LED will

light up to indicate that slave 1 has been disconnected

from the AS-Interface.

Please note

The red address selector LED must not light up when

the valve terminal is operated.

If the adress selector button has been unlocked:

Before connecting the valve terminal to the AS-Inter

face bus, therefore always lock the address selector

button by pressing it again.

3.3 Address assignment of the valves

During addressing, valve terminal CPV..-GE-ASI-8E6A-...

behaves like two individual slaves each with 4 inputs and

3 outputs (see sections 3.1 and 2).

The following fittings are possible for the two valve

terminal halves:

Festo CPV10/14-ASI-8E6A 2018-11b English8

Fitting valve locations 1 to 4 or 5 to 8

3 single-solenoid valves 1 double-solenoid valve,

1 single-solenoid valve

[J 1 2

7776

5676

Permitted DIP switch setting (see 3.7)

1: OFF

2: ON

3: OFF

4: ON

1: ON

2: OFF

3: OFF

4: ON

[J ... 2Addresses of the solenoid coils for AS-Interface address n/m

3Addresses or LEDs of the solenoid coils 14

4Addresses or LEDs of the solenoid coils 12

5Valve plates with 2 valve solenoid coils, like 2 single-solenoid

valves, 5/2-way double-solenoid valves or 5/3-way valves

(e.g. code J, N, C, H, G, D, I, E) *)

6Only blanking or separator plate permitted (e.g. code L, S, T)

7Valve plates with 1 valve solenoid coil (e.g. code M, F, A) *)

*) or blanking or separator plate

Festo CPV10/14-ASI-8E6A 2018-11b English 9

3.4 Connecting sensors (PNP inputs)

For connecting sensors use cable type KM8-M8-GSGD-...

and plugs with union nut, M8x1 thread.

Fasten the plugs with the aid of the union nut in order to

prevent unintentional loosening, e.g. due to shock. Seal

unused sensor connections with the protective caps type

ISK-M8. Only in this way can you comply with protection

class IP65.

Please note

The inputs are resistant to short circuits. If a short cir

cuit occurs, the slave will be switched off. The AS-Inter

face master regards this slave as missing. When the

short circuit is eliminated, the slave registers immedi

ately as capable of functioning.

1Inputs of the first

slave

2Inputs of the second

slave

3Pin assignment:

1: 24 V

3: 0 V

4: Input Ix

01234567

12 3

Festo CPV10/14-ASI-8E6A 2018-11b English10

3.5 Connecting the AS-interface bus and the load voltage

Please note

The sensor power supply for the inputs is provided via

the AS-Interface bus.

The power supply for the valves (outputs) is provided

by the additional supply: The valves must be supplied

separately with 24 V via the load voltage connection.

The AS-Interface has an integrated watchdog function

which resets the outputs if there is a bus communica

tion failure.

Warning

Use power supplies which guarantee reliable electrical

isolation of the operating voltage as per IEC/DIN EN

60204-1. Consider also the general requirements for

PELV circuits in accordance with IEC/DIN EN 60204-1.

By the use of PELV circuits, protection against electric

shock (protection against direct and indirect contact) is

guaranteed in accordance with IEC/EN 60204-1 (Electri

cal equipment for machines, General requirements).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Festo Touch-Terminal Handbücher

Festo

Festo CPV Series Stücklistenhandbuch

Festo

Festo MPA-C Series Bedienungsanleitung

Festo

Festo CPV GE-ASI-8E8A-Z-M8-CE Series Stücklistenhandbuch

Festo

Festo FB13 Bedienungsanleitung

Festo

Festo CPX-FB14 Bedienungsanleitung

Festo

Festo CPV GE-ASI Series Stücklistenhandbuch

Festo

Festo CPX Series Bedienungsanleitung

Festo

Festo IFB21-03 Series Bedienungsanleitung

Festo

Festo CPV -GE-CO3-8 Series Bedienungsanleitung

Festo

Festo VTSA-ASI 4E4A-Z Series Stücklistenhandbuch

Festo

Festo CPX-FB14 Bedienungsanleitung

Festo

Festo MPAC-V Bedienungsanleitung

Festo

Festo VTSA-44-MP Series Bedienungsanleitung

Festo

Festo CPV-SC Series Stücklistenhandbuch

Festo

Festo CPV E ASI-4E4A Series Stücklistenhandbuch

Festo

Festo CPX Series Bedienungsanleitung

Festo

Festo CPV-VI Series Bedienungsanleitung

Festo

Festo CPV...-GE-CO3-8 series Bedienungsanleitung

Festo

Festo MPA-S Bedienungsanleitung

Festo

Festo IFB11-03 Bedienungsanleitung

Festo

Festo CPX-FB6 Stücklistenhandbuch

Festo

Festo CPX Series Stücklistenhandbuch

Festo

Festo CPV-ASI-8E8A-ZCE Series Stücklistenhandbuch

Festo

Festo 03 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung