FIC PT-2006 Bedienungsanleitung

PT-2006

MAINBOARD

MANUAL

DOC No. : 15289

Rev. : A0

Date : 7, 1996

Part No. : 25-10526-00

Handling Precautions

Warning :

1. Static electricity may cause damage to the integrated circuits on the

mainboard.

Before handling any mainboard outside of its protective packaging,

ensure that there is no static electric charge in your body.

2. There is a danger of explosion if the battery is incorrectly replaced.

Replace only with the same or an equivalent type recommended by the

manufacturer.

3. Discard used batteries according to the manufacturer’s instructions.

Observe the following basic precautions when handling the mainboard or other

computer components:

■Wear a static wrist strap which fits around your wrist and is connected to a

natural earth ground.

■Touch a grounded or anti-static surface or a metal fixture such as a water

pipe.

■Avoid contacting the components on add-on cards, boards and modules and

with the “gold finger” connectors plugged into the expansion slot. It is best

to handle system components by their mounting bracket.

The above methods prevent static build-up and cause it to be discharged

properly.

Trademark

All trademarks mentioned in this manual are registered properly of the respective owners.

This manual may not, in whole or in part, be photocopied, reproduced, transcribed,

translated, or transmitted in whatsoever form without the written the consent of the

manufacturer, except for copies retained by the purchaser for personal archival purposes.

Notice

Overview

The PT-2006 mainboard combines the advanced capabilities of the Intel

82430VX PCIset with a high-performance concurrent PCI local bus architecture

to provide the ideal platform for unleashing the unsurpassed speed and power of

the Intel Pentium processor.

This highly-flexible mainboard is designed to run a full range of Intel Pentium,

Cyrix 6x86, IBM 6x86and AMD-K5 processors, and can be easily upgraded

using its 321-pin ZIF socket. The processor’s advanced performance is

complemented by a second level write back Pipeline Burst SRAM cache of up to

512KB and main memory of up to 128MB DRAM. The main memory is

installed using the board’s four 72-pin SIMM sockets and one 168-pin DIMM

socket that accept a choice of lightning-fast synchronous DRAM (SDRAM),

high-speed EDO, or standard Fast Page Mode DRAM.

The PT-2006 integrates a full set of I/O features onboard, including two 16550A

UART compatible serial ports, one EPP/ECP capable parallel port, and one

Floppy Disk Drive controller. It also comes with a built in Enhanced IDE

controller that provides convenient, high-speed PCI Bus Master connections with

up to four IDE devices, including Hard Disk and CD-ROM drives. Three 16-bit

ISA slots and four 32-bit PCI slots provide ample room for further expansion.

The mainboard also features support for the state-of-the-art Universal Serial Bus

(USB) that provides ease-of-use and high-speed Plug & Play connections to

future USB compliant peripheral devices. The IrDA compliant serial port and

optional onboard SIR support further enhance system

I/O connectivity.

This chapter gives a you a brief overview of the PT-2006 mainboard. In addition

to basic information on the board’s main components and features, it also

provides advice on how to upgrade and expand it. For updated BIOS, drivers, or

product release information, please visit FIC’s home page at:

http://www.fic.com.tw.

Congratulations on your decision to adopt the PT-2006 mainboard. With its high-

speed PCI local bus architecture and ultra-fast I/O connections, the PT-2006

provides the ultimate solution for optimizing the performance of your high-end

system.

Chapter 1

PT-2006 Mainboard Manual

Main Features

The PT-2006 mainboard comes with the following high-performance features:

■Easy Installation

Award BIOS with support for Plug and Play, auto detection of

Hard Drive and IDE features, and MS Windows 95 compatible.

■Flexible Processor Support

The onboard 321-pin ZIF socket supports Intel Pentium (P54C) CPU speed

75/90/100/120/133/150/166/200 MHz processors/P54CT / P55C (optional

by splitting the voltage regulator).

Cyrix 6x86-P120+ (100 MHz) / 6x86-P133+ (110 MHz) / 6x86-P150+

(120 MHz) / 6x86-P166+ (133 MHz) processors / M2 series processors

upgrade.

IBM 6x86-P120+ (100 MHz) / 6x86-P133+ (110 MHz) / 6x86-P150+

(120 MHz) / 6x86-P166+ (133 MHz) processors / M2 series processors

upgrade.

AMD K5-PR75 (75 MHz) / K5-PR90 (90 MHz) / K5-PR100 (100 MHz) /

K5-PR120 (90 MHz) / K5-PR133 (100 MHz) / K5-PR150 (120 MHz) /

K5-PR166 (133 MHz) processors.

■Leading Edge Chipset

Intel 82430VX chipset, including a CPU interface controller,

advanced cache controller, integrated DRAM controller, synchronous

ISA bus controller, PCI local bus interface, integrated power management

unit.

■Ultra-fast Level II Cache

Supports onboard 256KB/512KB synchronous PBSRAM direct-mapped

write-back cache memory and one SRAM module slot for expansion.

■Versatile Main Memory Support

Accepts up to 128MB RAM in two banks using 72-pin SIMMs of

4, 8, 16, 32, 64, 128MB or using a 168-pin DIMM with support for SDRAM,

EDO, or Fast Page Mode memory.

Overview

■ISA & PCI Expansion Slots

Three 16-bit ISA and four 32-bit non-shared PCI expansion slots provide all the

room you need to install a full range of add-on cards.

■USB Support

Onboard support for two Universal Serial Bus connectors via a plug-in

connector.

■Enhanced PCI Bus Master IDE Controller

Integrated Enhanced PCI local bus IDE controller with two connectors

supports up to four IDE devices such as Hard Disk, CD-ROM or Tape

Backup drives via two channels for high speed data throughput. This

controller supports PIO Modes 3 and 4, and DMA Mode 2 for optimized

system performance.

■Super Multi I/O

Integrated WB83877 Plug and Play Super I/O chipset features two 16550 UART

compatible serial ports, one EPP/ECP capable parallel port, one IR port, and one

Floppy Disk Drive connector.

PT-2006 Mainboard Manual

Package Checklist

Please check that your package contains all the items listed below. If you

discover any item is damaged or missing, please contact your vendor.

■The PT-2006 mainboard

■Serial port/parallel port cables with bracket

■Seriall port cable with bracket

■One IDE cable

■One floppy drive cable

■One SIR cable

■This user manual

■PS/2 mouse cable with bracket (Optional)

Overview

Cables

PT-2006 Mainboard Manual

This User Manual

This manual is designed to guide you and facilitate your use of the PT-2006

mainboard. It contains a description of the design and features of the mainboard,

and also includes useful information for changing the configuration of the board

and the system it is installed in. The manual is divided into three chapters, which

contain the main body of information normally referred to by users.

■Chapter 1 - Overview

gives an overview of the mainboard and describes its major components and

features.

■Chapter 2 - Installation Procedures

gives instructions on how to set up the mainboard, including jumper settings and

CPU installation guide.

■Chapter 3 - Award BIOS Setup

briefly explains the mainboard’s BIOS system setup in general and tells you how

to run it and change the system configuration settings.

NOTE : The material in this manual is for information only and is subject to

change without notice. We reserve the right to make changes in the product

design without reservation and without notification to its users. We shall not

be liable for technical or editorial omissions made herein; nor for incidental or

consequential damages resulting from the furnishing, performance, or use of

this material.

Overview

Something Interesting

This section provides useful information that you will need to know should you

decide to modify or upgrade the configuration of the mainboard and the system it

is installed in. If you do not have the confidence to upgrade the mainboard

yourself, we advise that you consult a qualified service technician for assistance.

The BIOS Setup Utility

The BIOS (Basic Input Output System) is the basic firmware that instructs the

computer how to operate. For the BIOS to work properly, there must be a record

of the computer’s hardware and configuration settings for it to refer to. This

record is created using the Setup Utility, a program that is stored permanently in

the BIOS ROM chip on the mainboard.

The system configuration record created by the Setup Utility is also stored on the

mainboard, but not permanently. This section of the memory it is stored is in the

NVRAM.

When you buy your computer, the system configuration record will already be

set and may in some cases differ from the basic defaults. The first time you use

your computer or when you need to re-configure your system, you should run the

Setup Utility and write down the settings.

PT-2006 Mainboard Manual

IRQ Functionality

As you read through this manual, you will see the term IRQ on a number of

occasions. It is important for you to know what this term means, particularly if

you intend to upgrade your system.

IRQ stands for Interrupt Request, the process in which an input or output device

tells the processor to temporarily interrupt its current task and immediately

process something from the source of the interrupt. When it has completed this,

the processor returns to the task it was already processing. Devices that need an

IRQ line to operate sometimes need to have exclusive use of that line.

A large number of add-on cards, such as sound cards and LAN cards, require the

use of an IRQ line to function. There is a total of 16 IRQs (IRQ0 to IRQ15)

available in a system, although some of them may already be in use by

components in the system such as the keyboard and mouse. Add-on cards that

need to use an IRQ draw from the unused group of IRQs. When installing a card

that uses an IRQ, it will have a default IRQ setting which you might have to

change if that IRQ is already in use and cannot be shared.

Both ISA and PCI add-on cards may need to use IRQs. System IRQs are

available to add-on cards installed on the ISA bus first; the remaining ones can

be used by cards installed on the PCI bus. There are two categories of ISA add-

on cards: so-called Legacy ISA cards, which need to be configured manually and

then installed in any available ISA slot; and Plug and Play (PnP) ISA cards,

which are configured automatically by the system. As a result, when you install

Legacy ISA cards, you have to carefully configure the system to ensure that the

installed cards do not conflict with each other by having the same IRQ. With PnP

cards, on the other hand, IRQs are assigned automatically from the ones

available in the system. In the case of PCI add-on cards, the BIOS automatically

assigns an IRQ card to the PCI slot the card is installed in.

Inhaltsverzeichnis

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung