FireAngel Wi-Safe2 Bedienungsanleitung

User Manual

WIRELESS TEST SILENCE LOCATE CONTROL UNIT

Please read me – as I could save your life.

Please retain this user manual for future reference

Keeping you safe from re and carbon monoxide

For a full range of smoke alarms and carbon monoxide alarms

visit www.reangel.co.uk

CONTENTS

Note: This User Manual is also available in large text and other

formats. Please call 0800 141 2561 for further information

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . 2

USER GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION GUIDE . . . . . . . . . . . . . . . . . . . . . . . 3

POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ACTIVATING THE CONTROL UNIT. . . . . . . . . . . . . . . . 4

HOW TO ‘LEARN-IN’ THE ALARM CONTROL

UNIT TO A WI-SAFE 2 NETWORK . . . . . . . . . . . . . . . . 5

MAKING THE ALARM CONTROL UNIT TAMPER PROOF . . . . . 5

TESTING THE ALARM SYSTEM . . . . . . . . . . . . . . . . . . . 6

PRODUCT FUNCTIONALITY . . . . . . . . . . . . . . . . . . . . 6

LOCATE BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SILENCE BUTTON. . . . . . . . . . . . . . . . . . . . . . . . . . 8

ALARM MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . 8

FAULT DETECTION . . . . . . . . . . . . . . . . . . . . . . . . . 9

REORGANISING A NETWORK . . . . . . . . . . . . . . . . . . 9

WHEN AN ALARM SOUNDS . . . . . . . . . . . . . . . . . . 10

LED STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . 12

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SUOMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

INTRODUCTION

USER GUIDE

IMPORTANT: If you are installing this product for

use by others, you must leave this manual (or a

copy of it) for the end user.

Wi-Safe 2 is the very latest in wireless technology from

Sprue Safety Products. It provides a network of wireless

radio frequency (RF) communication which can trigger

Wi-Safe 2 Alert products to alarm in the event of danger.

For use with Wi-Safe2 smoke, Heat and Carbon

Monoxide Alarms.

PLEASE READ THIS GUIDE IN FULL BEFORE USING

YOUR WTSL-F CONTROL UNIT.

Battery powered control unit with Test, Silence and

Locate function, non-replaceable 3V DC battery.

W2 module contained within product independently

tested to RF standard ETSI EN 300 220-2 V2 3 2 (2010-

02) by TRaC Global Ltd.

INSTALLATION GUIDE

FEATURES:

• Wi-Safe 2® technology, enabling wireless interlinking

between other Wi-Safe 2 products.

• Test / Silence ( ) button, allowing you to regularly test

all wirelessly interlinked alarms on a network Pressing

the silence button will reduce the sensitivity of alarms

for up to 10 minutes, unless carbon monoxide has

been detected, in which case you can use the ‘Locate’

function below to nd the source alarm.

• Locate button ( ), allowing you to silence all alarms but

the initiating alarm, during an alarm condition During a

fault condition, this feature will allow you to locate the

alarm in fault, in a similar way.

• Alarm memory function - allows you to investigate

previous alarm events.

• 10 year sealed for life battery

• 5 year warranty

• Fault indicator

• Carbon monoxide alarm indicator

• Test / Silence button

• Smoke/Heat alarm indicator

• Locate button

POSITIONING:

This Alarm Control Unit is suitable for use in domestic

premises only It should be installed at an accessible point

on the wall, in a location where it will not be accidentally

operated or knocked.

INSTALLATION ACTIVATING THE ALARM

CONTROL UNIT

• Ensure this Alarm Control Unit is installed by a

competent person who feels able to install it according

to the instructions

• Read all installation instructions prior to installing this

product

WARNING: To prevent injury, this Alarm Control Unit

must be securely attached to the wall in accordance

with the installation instructions.

To mount the bracket onto a wall:

Please ensure that you use the screws provided, as they

were chosen specically for use with this product. Drill

holes into the wall and insert supplied wall plugs. Screw

the bracket in place

The Alarm Control Unit has a sealed-in nonreplaceable

battery. To activate the control unit remove the

disabling tab. Upon activating the control unit all three

LED’s should simultaneously  ash twice, to indicate

that they are working.

Once the alarm is activated it can then be learnt into a

Wi-Safe 2 network, before securing to the wall bracket.

WIRELESS INTERLINK

The Alarm Control Unit is designed to be used as a

remote interface on a network of up to 49 products

within the Wi-Safe 2 range. The Alarm Control Unit can

be used to test, silence or locate any alarms on the Wi-

Safe 2 network. It is not designed to communicate with

wireless alarms from other ranges or manufacturers.

The control unit needs to be ‘learned-in’ or interlinked,

in order to communicate within the network.

Wi-Safe 2 enables wireless communication with any

other product with Wi-Safe 2 technology inside .

When one alarm detects smoke / heat / carbon

monoxide, the wireless module inside sends a signal

to all the connected alarms, ensuring almost

instantaneous reaction across the network.

HOW TO ‘LEARN-IN’ THE ALARM CONTROL

UNIT TO A WI-SAFE 2 NETWORK:

1 Using a ballpoint pen, briey push and release the

‘learn button’ on the back of the control unit. The red

LED next to the learn button will ash briey then

light up for approximately 5 seconds.

2 During these 5 seconds you need to briey press the

test button on an alarm already in the network, to

wirelessly interlink the two. The alarm will sound its

audible test pattern.

3 The red LED on the back of the control unit will ash

to indicate that it has been‘learned-in’successfully.

If the test button is not pressed quickly enough, the

‘learnin’process will fail If this happens, repeat

the process. Your Alarm Control Unit counts as one unit

within the network If it is installed retrospectively,

then the existing network cannot exceed 49 units

in size.

4 To complete the installation simply slide the control

unit onto the bracket. The control unit is now part

of the whole network. The method above assumes

you have already installed your alarm network, prior

to installing your Alarm Control Unit. If you want to

install your Alarm Control Unit rst, you can learn

your smoke, heat and CO alarm into it by following

the instructions in your alarm manual, using the

Alarm Control Unit as alarm 1.

MAKING THE ALARM CONTROL UNIT TAMPER PROOF

Do not complete this action until you have wirelessly

interlinked all of your alarms. The Alarm Control Unit

is provided with an anti-tamper feature, ensuring,

where needed it cannot be removed from the wall.

To make use of this feature you will need to push out

the two blanking plates on the top right-hand

side of the bracket, using a small screwdriver, being

careful to support the bracket fully whilst doing so.

Once the rest of the installation is complete, and the

control unit is xed to the bracket it can only be

removed using the following method:

Insert a small screwdriver into the hole on the top

right-hand corner of the control unit, until it stops,

this will disengage the lock, then gently ease the

control unit up to release it from the bracket.

TESTING THE ALARM SYSTEM

Press the Test / Silence ( ) button to conrm that the

control unit is operating properly. This will instigate

a three minute test. All networked alarms should

sound. To stop the test (earlier than 3 minutes),

simply press the Test / Silence ( ) button again. This

test should be performed on a weekly basis.

PRODUCT FUNCTIONALITY

Test button:

This allows you to test all wirelessly interlinked alarms

from one centralised location.

Silence button:

This will silence all wirelessly interlinked smoke and

heat alarms and reduce the system sensitivity for up

to 10 minutes.

Locate button:

In an alarm event this will silence all wirelessly

interlinked alarms except the initiating alarm which

has sensed Carbon Monoxide/Smoke.

Smoke/heat alarm indicator:

This indicates that a smoke / heat alarm has been

activated.

Carbon monoxide indicator:

This indicates that a carbon monoxide alarm has

been activated.

Fault indicator:

This indicates a fault with the control unit or one of

the alarms within the network.

LOCATE BUTTON

If the alarms are sounding and an alarm indicator is

ashing, but there’s no obvious hazard, pressing

the ‘Locate’ button ( ) will silence all wirelessly

interlinked alarms except for the initiating alarm

which has sensed smoke / heat or carbon

monoxide.

Within two minutes the system will return to

normal operation and the alarms will continue to

sound if smoke / heat or carbon monoxide is still

present. To make locating the alarm easier, the

control unit can be removed from its bracket and

carried around the property (providing the tamper

proof function has not been engaged), allowing

you to press the ‘Locate’ or ‘Test’ button whilst

moving from room to room.

ALARM MEMORY

If one of the alarm indicators is ashing every 10

seconds this indicates that a smoke alarm, heat alarm or

carbon monoxide alarm has previously been activated.

Pressing the ‘Locate’ button ( ) will clear the LEDs and

sound the source alarm so you can investigate this

further. You can press the ‘Locate’ button ( ) repeatedly

until the source alarm is identied.

Please Note: Only the most recent alarm event will

be visible. If both a CO and smoke / heat alarm have

previously been activated, both LED’s will show but the

CO alarm will always take precedence, and this is the

alarm which will sound. Never ignore an alarm. If there

is evidence of an alarm event, be sure to investigate

further.

SILENCE BUTTON

If the alarms are sounding and the smoke / heat alarm

indicator is ashing, but there’s no obvious hazard,

pressing the ‘Silence’ button ( ) will silence all wirelessly

interlinked alarms and reduce the system sensitivity for

up to 10 minutes. However if excessive smoke is sensed

the silence function will be overridden. The indicator

will continue to ash unless the smoke disappears.

Please Note:

An alarm cannot be silenced using the Alarm Control

Unit if carbon monoxide has been detected,

however the ‘Locate’ function will allow you to nd out

which of the CO alarms is the initiating alarm.

Inhaltsverzeichnis

Sprachen:

Andere FireAngel Rauchmelder Handbücher

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-625 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel ST-750 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel SI-610 Bedienungsanleitung

FireAngel

FireAngel ST-620 Thermoptek Bedienungsanleitung

FireAngel

FireAngel ST-230 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-632 Bedienungsanleitung

FireAngel

FireAngel SI-610 Bedienungsanleitung

FireAngel

FireAngel ST-630-INT Bedienungsanleitung

FireAngel

FireAngel ST-625-INT Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK ST-623E Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK ST-623E Bedienungsanleitung

FireAngel

FireAngel Thermoptek WST-630 Bedienungsanleitung

FireAngel

FireAngel Thermoptek WST-630 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel SW1 Bedienungsanleitung

FireAngel

FireAngel EZ-212 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung

Radal Technology

Radal Technology Cig-Arrête CSA-POD Bedienungsanleitung