Flashforge Creator 3 Bedienungsanleitung

1. Hot! Avoid touching the heating nozzle and heatingbuild platein operation.

Please refer to FlashForge official website www.flashforge.com to download

the newest User's Guide, Software and Instruction Videos.

(Support-Support Center-Select a Product)

2. Moving parts inprintermaycause injury. Do not wear gloves or other

sources of entanglement in operation.

Download

1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!

2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。

前往闪铸科技官方网站 www.sz3dp.com ，可以在[ 技术支持 ] 页面下载用户使

用手册、切片软件等资料，或查看相关操作视频。

资料下载

快速启动指南

Quick Start Guide

SZ20-ZN/EN-A02 / 金刚狼3

Creator 3

This guide is only applicable to FLASHFORGE Creator 3 3D printer

本指南仅适用于闪铸科技金刚狼3 3D打印机

中文 P17

1. Cut off packaging ties, and tear off

stretch wrap.

2. Lift outer packing box.

3. Remove top foam. 4. Remove foam around the printer.

5. Unrip tapes on four corners of the printer,

take bubble pack down.

6. Remove tapes on the top, open head cover.

7. Take top parts and foam out. 8. Remove the blue fastening tape.

9. Open the front door and take out the front foam which should contain two filament spools and

two waste boxes.

10. Remove clips on timing belt of X-axis and Y-axis.

11. Plug power cable into the input on the back and turn on the power switch. Tap[Tools], [Manual].

ToolsPreheatBuild

SettingStatus About

FilamentLevelHomeManual

HOME

14. Now you’ve unpacked your Creator 3.

12. Tap [Z-] to partially elevate the build plate. 13. Remove bottom foam pieces.

0.00

Y +

X -

X +

Z -

Z +

Y -

Getting to Know Your Creator 3

1. Touch Screen 2. USB Stick Input 3. Touch Screen Buttom 4. Right Extruder

13. Turbofan Baffle 14. Network Input 15. Power Switch 16. Power Input

9. Leveling Nut 10. Filament Cartridge Cover 11. Cartridge Cover Handle 12. Nozzle

5. Left Extruder 6. Nozzle Brush 7. Waste Box 8. Build Plate

Waste Box

Nozzle Brush

1.Hot!Avoid touching the heating nozzleand heatingbuild platein operation.

Pleasereferto FlashForgeofficial websitewww.flashforge.comtodownload

thenewestUser's Guide, Softwareand InstructionVideos.

(Support-SupportCenter-Selecta Product)

2.Moving parts inprintermaycause injury.Do not weargloves or other

sourcesofentanglement in operation.

Download

1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!

2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。

前往闪铸科技官方网站 www.sz3dp.com，可以在[ 技术支持 ] 页面下载用户使

用手册、切片软件等资料，或查看相关操作视频。

资料下载

快速启动指南

Quick Start Guide

SZ20-ZN/EN-A01

中文

/ 金刚狼3

Creator3

Thisguide is only applicable to FLASHFORGE Creator 3 3D printer

本指南仅适用于闪铸科技金刚狼3 3D打印机

How to use the leveling nuts

Rotate the nut clockwise

Rotate the nut anticlockwise

ToolsPreheatBuild

Setting Status About

Filament Level Home Manual

HOME

Language

WIFI

WLan hotspot

Door Opened Pause

Door Opened Detector

English 简体中文

English

日本語

繁體中文

Deutsch

ToolsPreheatBuild

Setting Status About

Filament Level Home Manual

HOME

1. Tap[Tools], tap[Level]to level the build plate.

2. Wait for the extruder and the build plate moving, after moving completed, choose to use which

extruder to level the build plate: left or right.

3. After leveling extruder confirmed,extruder will move to the first point to verify the distance

between nozzle and build plate. If verify completed, extruder will move to the second point to

verify the distance.

4. If the distance is not appropriate, please follow the prompts to adjust again till you see [OK] button.

Repeat steps 4 to level the second and third points. Then tap [Finish] to exit.

Select the extruder

Level

Left Extruder Right Extruder

Please wait...Initializing

Wait

Verifying the distance between nozzle

and plate...

Verify Next

Turn the nut counterclockwise 90°

Wait

Verify Next

Wait

Turn the nut clockwise 45°

1. Take out waste box, hang it on the hook

beside build plate. (One waste box on

each side)

2. Take out nozzle brush, install it on

mounting base. (One nozzle brush

on each side)

Install Waste box and Nozzle brush

Hook

Andere Handbücher für Creator 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Flashforge 3D-Drucker Handbücher

Flashforge

Flashforge Dreamer Desktop 3D Printer Bedienungsanleitung

Flashforge

Flashforge Inventor Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge ADVENTURER 3 Bedienungsanleitung

Flashforge

Flashforge CN/EN-A01 Bedienungsanleitung

Flashforge

Flashforge Creator Pro Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Guider 3 Bedienungsanleitung

Flashforge

Flashforge Adventurer 4 Bedienungsanleitung

Flashforge

Flashforge AD1 Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge Finder 3 Bedienungsanleitung

Flashforge

Flashforge Inventor 2 Bedienungsanleitung

Flashforge

Flashforge Adventurer 4 Bedienungsanleitung

Flashforge

Flashforge Creator Pro Bedienungsanleitung

Flashforge

Flashforge Adventurer 5M Pro Bedienungsanleitung

Flashforge

Flashforge Inventor Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Adventurer3 Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Waxjet 400 Bedienungsanleitung

Flashforge

Flashforge Creator 3 Pro Bedienungsanleitung

Flashforge

Flashforge Inventor Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch