Flashforge Creator Pro Bedienungsanleitung

SZ10-ZN/EN-A06

中文P19

2. The foam should contain: two filament guide

tubes, one SD card, two pieces of build tape,

one Flashforge leveling card, one After-sales

service, one Quick Start Guide and one User

Guide.

3. Firmly grasp the two sides handles of

Flashforge Creator Pro. Lift it out from the

carton and place it on a stable surface.

7. Remove the foam container. It should contain: a power cable, an USB cable, two spool holders,

a tool bag and an extruder’s accessory kit.

10. Open the door, remove top lid of the printer,

take filament out of the lid.

11. Find plastic board sealed with "Flashforge" at

the back of build plate, take out the foam blocks

at the back of plastic board.

9. Slide the X-axis Rods to the very back.

8. Shear three ties off on both sides of X-axis

guide rod.

13. Take power cable out and plug it into power

input.

12. Remove side foam.

14. Plug the other end of power cable into socket,

turn on the power switch.

16. Press downwards arrow, enter the next page.

18. Choose [Jog Mode], tap [OK]. 19. Tap rightwards arrow to the next page.

17. Press downwards arrow, enter the next page.

15. Operating on the LCD panel, press downwards

arrow to choose [Utilities], tap [Ok].

Monitor

Filament Loading

Preheat Settings

General Settings

Level Build Plate

Home Axes

Bot Statistics

Filament Odometer

Jog Mode

(Menu)

X+

Y-

X-

Profiles

Home offsets

Toolhead offsets

Jog Mode

FF Creator Pro

Print from SD

Preheat

Utilities

20. Tap rightwards arrow to the next page.

22. Remove foam under build plate.

21. Pess upwards arrow, the build plate goes up

until it comes to the highest position, loose

the button when the printer stops.

23. Press down arrow, loosen the button when

the build plate descends to the middle of the

printer. Tap [Ok], go back.

24. Tap [Ok], go back, tap leftwards arrow twice,

go back to the Home screen.

Jog Mode

Y+

Y-

(Menu) Z--X

Jog Mode

(Menu)

Z-

-Y

Z+

Jog Mode

(Menu)

Z-

-Y

Z+

FF Creator Pro

Print from SD

Preheat

Utilities

24. Unboxing completed! Recommended that you

take good care of packing materials for furthur

carrying and keeping.

Filament Guidetube x2

Tool bag:

Allen Wrench*2 / Knob / M3x8 Bolt*2 /

PTFE Tube*2 / Grease / Unclogging Pin Tool /

Wrench

Extruder’s accessory:

M3x8 Bolt*2 / M3x6 Bolt / Turbofan Baffle

User Guide

Build Tape x 2

3. Lid Slot

6. Platform Support 7. Knob

23. USB Cable Input

1. Place the dual extruder on the extruder

seat.

2. Take the M2.5 Allen Wrench from the tool

bag and two M3x8 bolts from the accessory

kit.

3. Adjust the extruder location to align the

bolt holes.

4. Secure the extruder onto the extruder

seat by screwing the M3x8 bolts in.

Andere Handbücher für Creator Pro

Inhaltsverzeichnis

Andere Flashforge 3D-Drucker Handbücher

Flashforge

Flashforge Adventurer 3 Pro 2 Bedienungsanleitung

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge Cura Handbuch

Flashforge

Flashforge CN/EN-A01 Bedienungsanleitung

Flashforge

Flashforge Foto 13.3 Bedienungsanleitung

Flashforge

Flashforge Creator Pro Montage- und Wartungsanleitung

Flashforge

Flashforge Adventurer 4 Bedienungsanleitung

Flashforge

Flashforge EN-A01 Bedienungsanleitung

Flashforge

Flashforge Inventor II Bedienungsanleitung

Flashforge

Flashforge Creator 4 Bedienungsanleitung

Flashforge

Flashforge Inventor II Bedienungsanleitung

Flashforge

Flashforge Adventurer 5M Pro Bedienungsanleitung

Flashforge

Flashforge ADVENTURER 3 Bedienungsanleitung

Flashforge

Flashforge Hunter Bedienungsanleitung

Flashforge

Flashforge Hunter Bedienungsanleitung

Flashforge

Flashforge Guider II Bedienungsanleitung

Flashforge

Flashforge Inventor Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge Finder Bedienungsanleitung

Flashforge

Flashforge Creator 3 Bedienungsanleitung

Flashforge

Flashforge DREAMER Bedienungsanleitung

Flashforge

Flashforge THOR500T Bedienungsanleitung

Flashforge

Flashforge Guider Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch