Flashforge Finder 3 Bedienungsanleitung
This guide is only applicable to FLASHFORGE Finder 3 3D printer
本手册仅适用于闪铸科技 发现者3 3D打印机
中文P20
用户使用手册
USER GUIDE
EN/CN-A01 Finder 3 发现者3
Content
Notes
Legal Statement
Equipment Parameters
Unpacking
Chapter 1 Equipment Introduction
1.1 - Product Introduction
1.2 - Kit Contents
Chapter 2 Preparation for Printing
2.1 - Assemble filament
2.2 - Build Plate
2.3 - Power On
2.4 - Leveling Build Plate
2.5 - Loading Filament
2.6 - Software Installation
Chapter 3 First Print
3.1 - Print
3.2 - Unloading Filament
3.3 - Wi-Fi Connection
3.4 - Connect Printer by Wi-Fi
3.5 - Firmware Upgrade
3.6 - Printing Notice
Chapter 4 FAQ
Chapter 5 Support and Service
02
02
03
04
05
05
06
07
07
08
08
09
11
11
12
12
13
13
14
15
16
17
19
01
Do not make any modifications to the printer. To avoid personal injury or property
damage please ensure your operation followed by the Manual.
Dress properly. Do not wear loose clothing or jewelry. Keeping your hair, clothing and
gloves away from moving parts.
Do not directly touch the nozzle and build plate to avoid high-temperature burn.
Do not expose the printer in flammable liquid, gas or dust environment (The high
temperature generated by operating printer may react with dust, liquid, and flamma-
ble gas in the air and cause fire).
Do not put the printer on a shaking place. It may affect the printing quality.
Children and untrained personnel are not allowed to operate the printer alone.
Operate the printer in a well-ventilated environment. Some materials may emit odors
during the printing process.
Do not manually move the nozzle or printing platform while booting up, lest printer
damage.
Never use the printer for illegal activities.
Never use the printer to make any food storage.
Never put the printed model into mouth.
Lower the build plate before loading/unloading filament. The distance between the
nozzle and build plate should be at least 50 mm.
Ensure regular maintenance for the printer; use dry cloth to remove dust and
adhered residues.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Notes
The user has no right to make any modification to this user guide.
Flashforge will not be responsible for any safety accidents caused by disassembly or
modification of the equipment by the customer. No one is allowed to modify or
translate this guide without the permission of Flashforge.
This guide is protected by copyright, and Flashforge reserves the right of final
interpretation of this guide.
Flashforge reserves the right to modify the guide due to subsequent equipment
upgrades.
First Edition (January 2022)
@Copyright 2021 Zhejiang Flashforge 3D Technology Co., Ltd. All Rights Reserved.
Legal Statement
02
Model
Print volume
Forming technology
Extruder quantity
Layer thickness
Nozzle diameter
Print precision
Filament
File format
Connectivity
Slicing software
Power specification
Total power
Hotbed temperature
Nozzle temperature
Resume printing function
Filament detection sensor
Screen
Language switch
Supports(OS)
Print speed
Position precision
Output file
Finder 3
190*195*200mm
FDM
1
0.1mm-0.4mm
Standard 0.4mm
±0.2mm
φ1.75mm PLA / PETG / TPU
stl / obj / amf /3mf / fpp / bmp /png / jpg / jpeg
Internal memory printing / USB stick printing /W i-Fi connection printing
FlashPrint / Cura / Simplify 3D
Input AC 115/230V 50/60Hz Outpu DC 24V
350W
≤110℃
≤260℃
Yes
Yes
4.3'' colorful touchscreen
Chinese / English / Japanese / French / Spanish / German
Windows 7/10 / Mac OS
≤180mm/s, 50-80mm/s normally
Z-axis 0.0025mm, X/Y-axis ±0.011mm
.gx / .g / .gcode
Equipment Parameters
03
Open the box, take out the user manual and the USB flash disk.
Remove the foam.
Lift the printer and put it on the desk, then take Finder 3 out of the plastic bag.
Remove the top foam, there should be a power cable included.
Take out the foam under nozzle.
Hold the platform and lift it carefully to remove the foam below it.
Discard the protective tapes all around.
Cut the cable ties which for fixing X-axis and Y-axis synchronous belt.
Cut the cable ties that used to hold the rods in place.
Cut the cable ties that used to hold the platform. Discard the protective tape around
it.
You’ve unpacked your printer. Please keep the kit and packing for future use.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Unpacking
04
第一章 设备简介
Chapter 1 Equipment Introduction
1.1 Product Introduction
1.
5.
9.
13.
1 7.
2.
6.
10.
14.
3.
7.
11.
15.
4.
8.
12.
16.
Y-axis Guide Rail
Glass platform
USB Stick Input
Turbofan Baffle
Filament detect sensor
X-axis Guide Rail
Clip
Power Voltage Switch
Power Switch
Z-axis Guide Rail
Leveling Nut
LED Light
Power Input
Limit position assembly
Touch Screen
Nozzle
Spool installation port
1
2
3
4
7
5
9
8
10
6
14 15
16
17
11
13
12
05
Power Cable
Nozzle
Needle
User Guide
Remove Tool
3D Printer
Material Rack
Glue
Wrenches and Screwdrivers Grease Flexible Spring Sheet
Filament
USB Flash Disk
1.2 Kit Contents
Thisguide is only applicable to FLASHFORGE Finder 3 3Dprinter
本手册仅适用于闪铸科技 发现者3 3D打印机
中文P20
用户使用手册
USER GUIDE
CN/EN-A01 Finder 3 发现者3
06
第一章 设备简介
Chapter 2 Preparation for Printing
2.1 Assemble filament
Install the material rack on the back of printer.1.
Insert the filament into the intake, pull out the PTFE tube from extruder; Then press the
handle to push filament into filament feeding roller.
2.
Press the handle
07
Plug in the power cord and toggle the switch to turn on the power. Do not disconnect the
cables when Finder 3 is powered on.
Attention
·
·
Damage might occur if voltage setting
is incorrect. Make sure the current input
voltage matches to your local power
supply (115/230V).
Plug in power cord and turn power
switch to 1 to turn it on.
2.2 Build Plate
Finder 3 is installed with the glass platform by default, while users can also use the
flexible removable platform.
Glass platform: The bottom is flatter, but the removal of the model requires a scraper; If
the glass platform is used when the ambient temperature is low, it is recommended to
apply glue on it before printing to increase the adhesion.
Flexible removable platform: It adopts magnetic adsorption, thus the model can be
easily removed by removing the flexible steel plate and then bending it.
2.3 Power On
If you switch from the glass platform to the flexible removable platform
plate, it is necessary to perform leveling and calibration.
Note
Installation method of the flexible removable
platform plate:
Remove the glass platform.
Stick the magnet above the heating plate.
Then the flexible steel plate can be
absorbed on the magnet.
1.
2.
3.
3
2
1
08
Inhaltsverzeichnis
Andere Flashforge 3D-Drucker Handbücher
Flashforge
Flashforge Inventor Bedienungsanleitung
Flashforge
Flashforge Adventurer 4 Bedienungsanleitung
Flashforge
Flashforge DREAMER Bedienungsanleitung
Flashforge
Flashforge CN/EN-A01 Bedienungsanleitung
Flashforge
Flashforge Creator Pro 2 Bedienungsanleitung
Flashforge
Flashforge Creator Gebrauchsanweisung
Flashforge
Flashforge Cura Handbuch
Flashforge
Flashforge Creator3 Bedienungsanleitung
Flashforge
Flashforge Invertor II Bedienungsanleitung
Flashforge
Flashforge Guinder II Bedienungsanleitung
Flashforge
Flashforge Inventor II Bedienungsanleitung
Flashforge
Flashforge Creator Pro Bedienungsanleitung
Flashforge
Flashforge Inventor II Bedienungsanleitung
Flashforge
Flashforge Guider Bedienungsanleitung
Flashforge
Flashforge Adventurer 5M Pro Bedienungsanleitung
Flashforge
Flashforge DREAMER Bedienungsanleitung
Flashforge
Flashforge Finder Bedienungsanleitung
Flashforge
Flashforge Creator Pro Bedienungsanleitung
Flashforge
Flashforge Finder Bedienungsanleitung
Flashforge
Flashforge Creator 3 Bedienungsanleitung
