Fluke 1630-2 Bedienungsanleitung
February 2017
©2017 Fluke Corporation. All rights reserved.
Specifications are subject to change without notification.
All product names are trademarks of their respective companies.
1630-2/1630-2 FC
Earth Ground Clamp
Users Manual
1
Introduction
The Fluke 1630-2/1630-2 FC Earth Ground Clamp (the
Product or Clamp) is a handheld, battery-operated clamp that
measures the ground resistance without auxiliary ground rods
and AC leakage current. The Clamp is used in multi-grounded
systems without disconnecting the ground under test.
The Clamp supports these applications:
•
Earth resistance and AC leakage current tests of high
voltage pylons, buildings, cell phone substations, and RF
transmitters
•
Inspection of lightning protection systems
The 1630-2 FC supports the Fluke ConnectWireless System
(may not be available in all regions). Fluke Connect is a
system that wirelessly connects your Clamp with an app on
your smartphone or tablet. The app shows the ground
resistance measurements on your smartphone or tablet
display. You can save these measurements and images to
Fluke ConnectCloud storage and share with your team. For
more information, see Fluke Connect Wireless System on
page 17.
Your shipment includes:
•
1630-2 or 1630-2 FC Earth Ground Clamp
•
AA alkaline batteries, IEC LR6 (x4, installed)
•
Resistance test/check loop
•
Safety Information and Quick Reference Guide (go to
www.fluke.com to download the 1630-2/1630-2 FC Users
Manual).
•
Carrying Case
How to Contact Fluke
To contact Fluke, call one of the following telephone numbers:
•
Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
•
Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
•
Canada: 1-800-36-FLUKE (1-800-363-5853)
•
Europe: +31 402-675-200
•
Japan: +81-3-6714-3114
•
Singapore: +65-6799-5566
•
Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit http://register.fluke.com.
To view, print, or download the latest manual supplement, visit
http://us.fluke.com/usen/support/manuals.
1630-2/1630-2 FC
Users Manual
2
Safety Information
A Warning identifies conditions and procedures that are
dangerous to the user. A Caution identifies conditions and
procedures that can cause damage to the Product or the
equipment under test.
Warning
To prevent possible electrical shock, fire, or
personal injury:
•
Carefully read all instructions.
•
Read all safety information before you use the
Product.
•
Do not alter the Product and use only as
specified, or the protection supplied by the
Product can be compromised.
•
Do not use the Product around explosive gas,
vapor, or in damp or wet environments.
•
Before each use, examine the Product. Look for
cracks or missing pieces of the clamp housing
or output cable insulation. Also look for loose or
weakened components. Carefully examine the
insulation around the jaws.
•
Comply with local and national safety codes.
Use personal protective equipment (approved
rubber gloves, face protection, and flame-
resistant clothes) to prevent shock and arc blast
injury where hazardous live conductors are
exposed.
•
Use Product-approved measurement category
(CAT), voltage, and amperage rated accessories
(probes, test leads, and adapters) for all
measurements.
•
Do not use the Product if it is altered or
damaged.
•
Disable the Product if it is damaged.
•
Do not use the Product if it operates incorrectly.
Earth Ground Clamp
Safety Information
3
•
Do not use the Product above its rated
frequency.
•
Limit operation to the specified measurement
category, voltage, or amperage ratings.
•
Do not touch voltages >30 V ac rms, 42 V ac
peak, or 60 V dc.
•
Hold the Product behind the tactile barrier.
•
The battery door must be closed and locked
before you operate the Product.
•
Replace the batteries when the low battery
indicator shows to prevent incorrect
measurements.
•
Remove the batteries if the Product is not used
for an extended period of time, or if stored in
temperatures above 50 °C. If the batteries are
not removed, battery leakage can damage the
Product.
•
Do not operate the Product with covers
removed or the case open. Hazardous voltage
exposure is possible.
•
Repair the Product before use if the battery
leaks.
•
Use only specified replacement parts.
•
Have an approved technician repair the
Product.
•
Remove the input signals before you clean the
Product.
•
Do not operate within external low frequency
magnetic fields >30A/m.
Symbols used on the Product and in this manual are
explained in Table 1.
1630-2/1630-2 FC
Users Manual
4
Table 1. Symbols
Symbol Description Symbol Description
WARNING. RISK OF DANGER. Battery
WARNING. HAZARDOUS
VOLTAGE. Risk of electric shock. Certified by CSA Group to North American safety standards.
Consult user documentation. Conforms to European Union directives.
Application around and removal
from uninsulated hazardous live
conductors is permitted. Conforms to relevant Australian EMC standards.
Double Insulated Certified by TÜV SÜD Product Service.
Do not operate within external low
frequency magnetic fields >30A/m. Conforms to relevant South Korean EMC Standards.
China metrology certification mark for measuring instruments manufactured in the People’s Republic of China (PRC).
Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the
building’s low-voltage MAINS installation.
Measurement Category IV is applicable to test and measuring circuits connected at the source of the building’s low-
voltage MAINS installation.
This product complies with the WEEE Directive marking requirements. The affixed label indicates that you must not
discard this electrical/electronic product in domestic household waste. Product Category: With reference to the
equipment types in the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control
Instrumentation" product. Do not dispose of this product as unsorted municipal waste.
Earth Ground Clamp
Before You Start
5
Before You Start
This section is information to know before you use the Clamp.
Warning
To prevent possible electrical shock, fire, or
personal injury:
•
For optimal readings, make sure the conductor
is positioned between the alignment marks on
the jaws.
•
Make sure the jaws are perpendicular to the
conductor.
•
Do not use the HOLD function to measure
unknown potentials. When HOLD is turned on,
the display does not change when a different
potential is measured.
•
Replace the batteries as soon as the low
battery indicator appears.
Power On/Off
The Clamp has a power on/off button:
1. Push to turn on the Clamp.
2. Push and hold >2 s. to turn off the Clamp.
If Auto-Off Power is turned on, the Clamp turns off after
20 minutes of no use. See Power Auto-Off on page 11 for
more information about how to set this feature.
Display Features and Controls
See Table 2 and Table 3 for the display features and button
controls.
1630-2/1630-2 FC
Users Manual
6
Table 2. Display Features
Item Description Item Description
Fluke Connect
Measurement value or
custom setting
Hold
Ohms function
ID#
Current in mA or A
Alarm
Current type is AC
Set Time
Memory in use
Indicator for noise in
ground electrode/rod
Filter is on
(bandwidth 40 Hz to 70 Hz)
Battery
Logging Interval settings
Date/Time format
Jaws open
Date/Time/ID number
Setting or explore for LOG
124
3567
8
9
10
11
12
13
14
15
16
17
18
Earth Ground Clamp
Before You Start
7
Table 3. Controls
Item Description
Jaw
Tactile barrier
Fluke Connect(radio) on/off
Record measurements
Hold the displayed value
LCD
Backlight
Filter on/off
Enter
Value increment/decrement
Change Clamp settings
Select type of measurement
Power on/off
Alarm
Jaw trigger
Jaw trigger lock
1
3
5
6
7
8
9
11
12
15
4
10
13
14
2
16
1630-2/1630-2 FC
Users Manual
8
Setup
Push to change these settings:
•
Log interval
•
Alarm threshold
•
Time
•
Clamp settings
Log Interval
The time interval for data logging is the time between
measurements.
To set the log interval:
1. Push until LOG INTERVAL shows in the display. See
Figure 1.
The interval is shown in minutes:seconds format and is
adjustable from 00:00 to 59:59.
2. Push to enable the change mode. The digits start to
blink.
3. Push / to increment/decrement the interval by
1 second.
4. After you select the value, push until the digits stop
blinking.
5. Push to go back to the measurement mode.
Figure 1. Log Interval
Earth Ground Clamp
Setup
9
Alarm Threshold
In alarm mode, the display shows ALARM and the beeper
sounds when the measurement is outside the set threshold.
The Clamp compares the reading with the high and low
values. If the reading is larger than the high value, the Clamp
beeps and shows -- on the display. If the reading is less
than the low value, the Clamp beeps and -- shows on the
display.
To set the alarm threshold:
1. Push until ALARM shows in the display. See Figure 2.
2. Push to select the type as Amps HI, Amps LO,
Ohms LO, or Ohms HI.
3. Push / to increment/decrement the value.
4. Push to confirm the current input and move to the
next setting.
5. Push to go back to the measurement mode.
Figure 2. Alarm Functions
Andere Handbücher für 1630-2
3
Inhaltsverzeichnis
Andere Fluke Messgerät Handbücher
Fluke
Fluke 1520 Bedienungsanleitung
Fluke
Fluke 90i-610s Bedienungsanleitung
Fluke
Fluke 85RF Bedienungsanleitung
Fluke
Fluke FIBER OneShot Bedienungsanleitung
Fluke
Fluke 80i-110s Bedienungsanleitung
Fluke
Fluke 30 Bedienungs- und Montageanleitung
Fluke
Fluke 721A Bedienungsanleitung
Fluke
Fluke ScopeMeter 123 Bedienungsanleitung
Fluke
Fluke PQ Window Bedienungsanleitung
Fluke
Fluke VIBRONET Signalmaster Bedienungsanleitung
Fluke
Fluke endurance series Bedienungsanleitung
Fluke
Fluke 80K-6 Bedienungsanleitung
Fluke
Fluke PG7607 Bedienungsanleitung
Fluke
Fluke 301A Bedienungsanleitung
Fluke
Fluke 430 Series Gebrauchsanweisung
Fluke
Fluke 1736 Bedienungsanleitung
Fluke
Fluke 5606 Bedienungsanleitung
Fluke
Fluke 360 Gebrauchs- und Pflegehandbuch
Fluke
Fluke 43 Bedienungsanleitung
Fluke
Fluke PRV240 Bedienungsanleitung
