Fluke 726 Konfigurationshandbuch

Manual Supplement

Manual Title: 726 Users Supplement Issue: 2

Print Date: September 2005 Issue Date: 3/08

Revision/Date: Page Count: 6

This supplement contains information necessary to ensure the accuracy of the

above manual. This manual is distributed as an electronic manual on the

following CD-ROM:

CD Title: 725/726

CD Rev. & Date: 4, 9/2005

CD PN: 1549615

726 Users Manual Supplement

3/07 1

Change #1

On page 2, replace the Pulse row with the following:

Pulse 1-100,000

Frequency Max 15 kHz

1-10,000

Frequency Range 2 CPM to 15 kHz

On page 12, Table 4, replace the Description for Number Lwith the following:

Cycles through:

ESlow repeating 0 % - 100 % - 0 % ramp

PConfigurable repeating 0 % - 100 % - 0% ramp

NConfigurable repeating 0 % - 100 % - 0 % ramp in 25 % steps

LUsed for the pulse train and totalizer functions.

On page 13, replace Figure 4 with the following:

Manual Supplement 726 Users

2 3/07

Low Battery

Symbol

Loop

Indicator

Memory Locations

for Calibrator Setups

Units

Display

Auto

Ramp

Mode

Indicator

HART Mode

Indicator

% Error

Indicators

Figure 4. Elements of a Typical Display

726 Users Manual Supplement

3/07 3

On page 14, under Configuration Menus, add the following under the last bullet:

•Step time

•Ramp time

On page 15, under Shut Down Mode, replace numbered steps with the following:

1. Press Cuntil SHUT DOWN appears on the display.

2. Use Xand Wto increase or decrease the time.

3. Use Yand Zto turn on and off.

4. Press Sto save the setting.

On page 16, under Hart®Resistor ON/OFF, replace step 2 with the following:

2. Use Vor Yand Zto toggle ON and OFF.

Add the following below the Note:

Step Time

Step Time sets the ramp step Ntime from 1 sec to 99 sec.

1. Press Cuntil STEP TIME appears on the display.

2. Use Xand Wto set the step time.

3. Press Sto save the setting.

Manual Supplement 726 Users

4 3/07

Ramp Time

Ramp Time sets the ramp Ptime from 5 sec to 99 sec.

1. Press Cuntil RAMP TIME appears on the display.

2. Use Xand Wto set the ramp time.

3. Press Sto save the setting.

On page 25, Table 6, add the following:

Cu10 10 ΩCopper 0.0042 Ω/°C -100 to 250

On page 42, under Auto Ramping the Output, replace the 2nd and 3rd bullets with the following:

•P0 % - 100 % - 0 % configurable time smooth ramp. Set ramp time using configuration

menu.

•N0 % - 100 % - 0 % Stair-step ramp in 25 % steps, pausing at each step. Set ramp

time using configuration menu. Steps are listed in Table 7.

On page 60, under Frequency Measurement, add the following to the bottom of the table:

Sensitivity: 1 V peak to peak minimum

Waveform: Squarewave

726 Users Manual Supplement

3/07 5

On page 62, change the Range entries for “Thermocouple in mV read” and “Thermocouple in

mV source”:

From:

-10 °C to 75 °C

To: -10 mV to 75 mV

On page 63, under the RTD Accuacy (Read and Source) (ITRS-90) table, replace the CU10 row

with the following:

Cu10 -100.0 250.00 1.8

On page 64, under Pulse Read and Pulse Source, replace the Frequency entry with the

following:

2 CPM to 15 kHz

Manual Supplement 726 Users

6 3/08

Change #2

On page 7, Table 2, add the following:

;Conforms to Australian C-Tick directives

Andere Handbücher für 726

Inhaltsverzeichnis

Andere Fluke Messgerät Handbücher

Fluke

Fluke E-DWT-H Bedienungsanleitung

Fluke

Fluke MDA-550 Bedienungsanleitung

Fluke

Fluke DPM2 Plus Bedienungsanleitung

Fluke

Fluke i5s-PR 1750 5A Bedienungsanleitung

Fluke

Fluke OptiView Bedienungsanleitung

Fluke

Fluke 430 Series Gebrauchsanweisung

Fluke

Fluke 945 Bedienungsanleitung

Fluke

Fluke 1520 Bedienungsanleitung

Fluke

Fluke PRV240 Bedienungsanleitung

Fluke

Fluke 721A Bedienungsanleitung

Fluke

Fluke ScopeMeter 190-104 Bedienungsanleitung

Fluke

Fluke Victoreen 451P Bedienungsanleitung

Fluke

Fluke CPS-40M-HC40 Bedienungsanleitung

Fluke

Fluke FOM Series Referenzhandbuch

Fluke

Fluke 902 Bedienungsanleitung

Fluke

Fluke 9000A-006 Bedienungsanleitung

Fluke

Fluke 80i-110s Bedienungsanleitung

Fluke

Fluke VIBGUARD IIoT Leitfaden

Fluke

Fluke 1735 Bedienungsanleitung

Fluke

Fluke 377 Bedienungsanleitung

Fluke

Fluke 301D Bedienungsanleitung

Fluke

Fluke 80K-6 Bedienungsanleitung

Fluke

Fluke 312 Bedienungsanleitung

Fluke

Fluke i800 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung