Fluke I1000s Konfigurationshandbuch

Manual Supplement

Manual Title: i1000s Calibration Supplement Issue: 1

Part Number: 1574933 Issue Date: 7/01

Print Date: May 2001 Page Count: 2

Revision/Date:

This supplement contains information necessary to ensure the accuracy of

the above manual. Enter the corrections in the manual if either one of the

following conditions exist:

1. The revision letter stamped on the indicated PCA is equal to or higher

than that given with each change.

2. No revision letter is indicated at the beginning of the change.

i1000s Calibration Manual Supplement

7/01 1

Change #1

On page 8, Table 4, under Recommended Model,

Replace:

Digital Multimeter Hp 3458A or equivalent

With:

Digital Multimeter Agilant 3458A or equivalent

Delete the following from Table 4,

AC/DC Shunt IET Labs-DCCS-200 0.1e- 0.1% non-inductive

Replace the entire

Phase Shift

section, Table 5 and Figure 3 with the following:

Phase Shift Test

To check Phase Shift performance, set up the equipment as shown in Figure 3.

1. Center the Current Probe around the coil.

2. Set the calibrator output to 1V (phase meter reference input), 1A and 50 Hz, per step 1 of Table 5.

Performance Test Steps.

3. Verify that the phase meter reading is within the “Phase in Deg” limits of Table 5.

Table 5. Performance Test Steps

i1000s

mV Output Phase in Deg.

Step Coil Range 5520A

Output

5500A

Coil

I. Prim. Freq. Min. Max. Min. Max.

1 50 turn 1 mV/A 1 A 50.0 A 50 Hz 48.5 51.5 -3.0 3.0

2 50 turn 1 mV/A 2 A 100 A 400 Hz 98.0 102.0 N/A N/A

3 50 turn 1 mV/A 4 A 200 A 60 Hz 197.0 203.0 -2.0 2.0

4 50 turn* 1 mV/A 14 A 700 A 50 Hz 692.0 708.0 -2.0 2.0

5 1 turn 10 mV/A 5 A N/A 50 Hz 44.0 56.0 -15.0 15.0

6 50 turn 10 mV/A 0.4 A 20 A 50 Hz 191.0 209.0 -10.0 10.0

7 50 turn 10 mV/A 2 A 100 A 50 Hz 975.0 1025.0 -10.0 10.0

8 1 turn 100 mV/A 0.50 A N/A 50 Hz 38.5 61.5 N/A N/A

9 1 turn 100 mV/A 2.00 A N/A 50 Hz 184.0 216.0 -15.0 15.0

10 1 turn 100 mV/A 10 A N/A 50 Hz 960.0 1040.0 -15.0 15.0

* 700 A/ 50 Hz in 1 mV/A range has a TUR of 3.3

4. Continuing to use 1V as the phase meter reference input, set the calibrator output for the remaining

steps listed in Table 5. Steps 2 and 8 do not require phase tests.

5. Verify that the phase meter readings meet the "Phase in Deg" limits for each step.

Manual Supplement i1000s Calibration

27/01

0•

123

456

789

ENTER

mVHz

FIELD

EDIT

OPRSTBY EARTH SCOPE

EXGRD MENU

SHIFT

RESET

SETUP

REF

NEW

MEAS

¡F

dBm sec

¡C

POWER

MULT

DIV

MODES

5520A

CALIBRATOR

TRIG

GUARD

20A

NORMAL AUX SCOPE

OUT

V, , ,RTD A, -SENSE, AUX V

20V PK MAX

mV Output

Black

Red

5520A calibrator

Phase meter

1 turn coil

5500A/coil

Tie Aux Com and

Normal Com together

using heavy gauge

wire or bus bar.

akp03f.eps

Figure 3. Phase Check Setup

mV Output Test

1. Connect the equipment as shown in Figure 5.

2. Set the calibrator output and coil for each step of Table 5.

3. Verify that the voltmeter reading is within the “i1000S mV Output” limits of Table 5.

Andere Handbücher für i1000s

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fluke Messgerät Handbücher

Fluke

Fluke VIBGUARD IIoT Bedienungsanleitung

Fluke

Fluke 85RF Bedienungsanleitung

Fluke

Fluke i40s-PR 1750 40A Bedienungsanleitung

Fluke

Fluke PRV240 Bedienungsanleitung

Fluke

Fluke i5s Bedienungsanleitung

Fluke

Fluke 323 Bedienungsanleitung

Fluke

Fluke FIBER OneShot Bedienungsanleitung

Fluke

Fluke 321 Gebrauchsanweisung

Fluke

Fluke i3000s Flex Series Bedienungsanleitung

Fluke

Fluke 305 Bedienungsanleitung

Fluke

Fluke 525B Bedienungsanleitung

Fluke

Fluke Biomedical IDA-4 Plus Operators Bedienungsanleitung

Fluke

Fluke 321 Technisches Handbuch

Fluke

Fluke TS54 TDR Bedienungsanleitung

Fluke

Fluke 9040 Bedienungsanleitung

Fluke

Fluke i410 Bedienungsanleitung

Fluke

Fluke ASM-990 Series Bedienungsanleitung

Fluke

Fluke 805 FC Bedienungsanleitung

Fluke

Fluke 789 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 5790A Bedienungsanleitung

Fluke

Fluke CO-220 Bedienungsanleitung

Fluke

Fluke 789 Bedienungsanleitung

Fluke

Fluke 772 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 80K-40 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Fluke i1000s Konfigurationshandbuch

Beliebte Messgerät Handbücher anderer Marken