Franke AQUAMIX AQRM175 Bedienungsanleitung

ZMI_001_2000100069-AQRM312_#SALL_#AQU_#V3.fm/24.02.12

Installation and operating instructions Montażi instrukcja obsługi

Franke Aquarotter GmbH, Germany

EA-Nr.: 7612982003028

FAR-Best.-Nr.: 2000100917

AQRM175

EA-Nr.: 7612982000515

FAR-Best.-Nr.: 2000100070

AQRM311

EA-Nr.: 7612982000522

FAR-Best.-Nr.: 2000100069

AQRM312

Inhaltsverzeichnis11.fm

................................................................ 3

Please refer to the graphics in the German

Installation and Operating Instructions.

................................................................ 11

Prosimy przyjąć grafikęz niemieckiej instrukcji

montażu i obsługi.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

0English

AQUAMIX Self-closing Single Mixer

7612982003028 ......... Vertical-mounted mixer tap

7612982000515 ......... Single clamp-on tap

7612982000522 ......... Dual clamp-on tap

Please refer to the graphics in the German Installation and Operating Instructions.

0Table of Contents

1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of Product

5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

9. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation, Function and Commissioning

10. Installation (FAR Order No. AQRM175) . . . . . . . . . . . . . . . . . . . . 5

11. Installation (FAR Order No. AQRM311) . . . . . . . . . . . . . . . . . . . . 6

12. Installation (FAR Order No. AQRM312) . . . . . . . . . . . . . . . . . . . . 6

13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

14. Adjusting the Flow Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

15. Setting the Temperature Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance

16. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

17. Replacing an Aerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

18. Replacing the Grit Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

19. Replacing the Non-return Valve . . . . . . . . . . . . . . . . . . . . . . . . . . 9

20. Replacing the Functional Part . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

21. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

22. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

1. Abbreviations and Units

2. Key

Warning!

Failure to observe can result in injury or even death.

Caution!

Failure to observe can result in material damage.

☞Important!

Failure to observe can cause the product to malfunction.

☞Useful information for optimally handling the product.

3. Warranty

Liability is accepted according to the General Terms and Conditions of Business and

Supply.

Use original replacement parts only!

4. Important Notes

• Installation, commissioning and maintenance are to be performed only by a

qualified technician according to the instructions provided and in accordance with

legal requirements and acknowledged rules of technology.

• All technical connection regulations specified by the local water and electricity

supply utility companies must be complied with.

5. Application

AQUAMIX self-closing single mixer DN 15 with angled outlet, for connection to hot

and cold water. Adjustable flow duration.

SW Width A/F

EA-Nr. European Article Number

FAR-Best.-Nr. Franke Aquarotter Order Number

Conversion 1 mm = 0.03937 inches

1 inch = 25.4 mm

All length specifications in the graphics are in mm.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

6. Technical Specifications

7. Scope of Delivery

8. Dimensions

9. Installation Example

10. Installation (FAR Order No. AQRM175)

Warning!

Use the fitting only with the non-return valves and the grit filters specified.

Failure to observe can result in an increased bacterial load in drinking water and

cause a health risk or even risk of death.

☞Important!

Before installing, flush the pipes in compliance with DIN 1988.

10.1

Apply sealing material to the S-connectors (a) and screw them in.

☞Apply grease to the O-rings on the S-connectors!

10.2

Place the wall plate (b) over the S-connectors, align it, and then secure it with the

nuts (c).

10.3

Slide the flange (d) on to the wall plate and secure it with the washer (e) and the

screw (f).

10.4

Insert the grit filters (g).

10.5

Screw in the faucet screw (h) until it protrudes 16 mm and the borehole is vertical.

☞Apply grease to the O-rings on the guide bushing!

10.6

Insert the guide bushings (i).

Minimum flow pressure: 1.0 bar

Recommended flow pressure: 1-5 bar

Maximum operating pressure: 10 bar

Calculation flow rate: 0,07 l/s 0,07 l/s

Volumetric flow: 0.10 l/s at a flow pressure of 3 bar

Flow duration at 38 °C: 1-15 s adjustable

Quantity Description

1 AQUAMIX self-closing single mixer

1 Installation and Operating Instructions

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

10.7

Attach the fitting (k).

10.8

Secure the fitting with the grub screw (l).

10.9

Turn on the water supply.

10.10

Check the connections for leaks.

11. Installation (FAR Order No. AQRM311)

Warning!

Use the fitting only with the non-return valves and the grit filters specified.

Failure to observe can result in an increased bacterial load in drinking water and

cause a health risk or even risk of death.

☞Important!

Before installing, flush the pipes in compliance with DIN 1988.

☞Important!

When installing the distribution pipes, ensure that a gap of 45 mm is maintained. Drill

the boreholes so that they are exactly in line vertically. The correct distances of the

pipes as well as the positions of the boreholes must not be forced with the mixer

body and the cover.

11.1

Drill 14 mm holes into the distribution pipes (b).

11.2

Place the clamper (c) and seals on the pipes, and then screw-fasten from the rear

with the clamp cover (a).

☞Apply grease to the O-rings on the guide bushing!

11.3

Insert the grit filters (d) and the guide bushings (e) into the clamper (c).

11.4

Slide the fitting (g) on to the guide bushings.

11.5

Secure the fitting with the grub screw (f).

11.6

Turn on the water supply.

11.7

Check the connections for leaks.

12. Installation (FAR Order No. AQRM312)

Warning!

Use the fitting only with the non-return valves and the grit filters specified.

Failure to observe can result in an increased bacterial load in drinking water and

cause a health risk or even risk of death.

☞Important!

Before installing, flush the pipes in compliance with DIN 1988.

☞Important!

When installing the distribution pipes, ensure that a gap of 45 mm is maintained. Drill

the boreholes so that they are exactly in line vertically. The correct distances of the

pipes as well as the positions of the boreholes must not be forced with the mixer

body and the cover.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

12.1

Drill 14 mm holes into the distribution pipes (b).

12.2

Place the clamper (a) and seals on the pipes, and then screw-fasten from below with

the clamp cover (c).

☞Apply grease to the O-rings on the guide bushing!

12.3

Insert the grit filters (d) and the guide bushings (e) into the clamper (a).

12.4

Slide the fittings (g) on to the guide bushings.

12.5

Secure the fittings with the grub screws (f).

12.6

Turn on the water supply.

12.7

Check the connections for leaks.

13. Function

Triggering water flow

13.1

Press the push cap.

• Water flows.

• Water flow stops automatically after a set flow duration.

☞The flow time can be set in the range 1–30 s.

Selecting the temperature

14. Adjusting the Flow Duration

14.1

Use a screwdriver to carefully prise up the plug.

14.2

Remove the plug.

14.3

Loosen the grub screw using a hollow hexagon wrench.

14.4

Remove the push-cap handle.

14.5

Set the flow duration with a screwdriver.

a: Blade width 3 mm

+ longer flow duration (max. 50 s)

– shorter flow duration (min. 1 s)

14.6

Trigger the valve to measure the flow duration.

☞Important!

When replacing the push-cap handle, ensure that the driver bar latches into the

corresponding slot.

14.7

After setting the required flow time, replace the push-cap handle.

14.8

Reassemble in the reverse order.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

15. Setting the Temperature Limiter

Warning!

If the hot-water supply temperature is more than 45 °C, set the temperature limiter.

Failure to observe can cause bodily harm due to scalding.

☞The temperature limiter is not a scald protector.

15.1

Remove the push-cap handle (siehe Kapitel 14.).

15.2

Use a screwdriver to carefully prise off the stop ring and then use your hand to pull it

off from the teeth.

15.3

Mount the push-cap handle and trigger the fitting.

15.4

Turn the push-cap handle until the desired maximum hot-water temperature is

reached.

15.5

Push the stop ring back on the teeth so that the nose of the stop ring is positioned up

against the right-hand stop of the housing.

☞Important!

While fitting the push-cap handle, make sure that the driving lug locks properly into

the corresponding groove (siehe Kapitel 14.).

15.6

Reassemble in the reverse order.

16. Maintenance and Servicing

Depending on the quality of the water, the local conditions and the rules and regula-

tions applicable on site, the fitting must be maintained and serviced at regular

intervals.

Perform maintenance on the following components:

• Aerators (siehe Kapitel 17.)

• Filters (siehe Kapitel 18.)

• Non-return valves (siehe Kapitel 19.)

Use suitable cleaning agents that are not harmful to the fittings in a proper manner

and rinse with water after use. High-pressure cleaners must not be used for

cleaning.

Removing the Fitting

Some maintenance work requires the fitting to be removed.

16.1

Turn off the water supply.

16.2

Trigger the valve.

16.3

Loosen the grub screw.

16.4

Pull off the fitting.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

17. Replacing an Aerator

17.1

Unscrew the aerator (a).

17.2

Screw on the new aerator.

18. Replacing the Grit Filters

18.1

Remove the fitting (siehe Kapitel 16.).

18.2

Pull out the guide bushings (a).

18.3

Replace the grit filters (b).

☞Important!

Be careful to insert the grit filters the right way round.

18.4

Reassemble in the reverse order.

19. Replacing the Non-return Valve

19.1

Remove the fitting (siehe Kapitel 16.).

19.2

Pull out the guide bushings (a).

19.3

Use a special wrench (c; FAR Order No. 2000105636) to pull the non-return valves

(b) out of the fitting .

Caution!

Observe the installation direction of the non-return valves.

19.4

Reassemble in the reverse order.

20. Replacing the Functional Part

20.1

Turn off the water supply.

20.2

Trigger the valve.

20.3

Remove the push-cap handle (siehe Kapitel 14.).

20.4

Remove the circlip.

20.5

Remove the pressure spring and the handle socket.

20.6

Use a socket spanner to remove the functional part.

☞Important!

While fitting the push-cap handle, make sure that the driving lug locks properly into

the corresponding groove (siehe Kapitel 14.).

20.7

Reassemble in the reverse order.

ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3

21. Fault Correction

If you are unable to correct a fault or if the fault is not described in the fault correction

section, please inform our customer service department!

22. Replacement Parts

Fault Cause Remedy

Water does not flow – Stop valve is closed ➯Open it

– Functional part faulty ➯Replace it

Water flows conti-

nuously

– Functional part faulty ➯Replace it

– Aerator calcified ➯Clean it

Water flow too weak – Aerator calcified ➯Clean it

– Supply pressure too low ➯Check it

– Grit filter/Non-return valve dirty ➯Clean it

– Water flow regulator not fully

opened

➯Open it

Flow duration too

short or too long

– Incorrect setting ➯Adjust it

– Grit filter is clogged ➯Clean it

– Aerator/shower head clogged with

dirt

➯Clean it

– Functional part/upper section faulty ➯Replace it

Water is too hot – Temperature limit is incorrectly set

or not set at all

➯Adjust it

– Cold water is turned off ➯Open it

– Grit filter/Non-return valve in the

cold-water connection is faulty

➯Replace it

Water is too cold – Grit filter/Non-return valve in the

hot-water connection is faulty

➯Replace it

– Hot water is turned off ➯Open it

Bezeichnung Best.-Nr.

1 Push-cap handle . . . . . . . . . . . . . . 2000104775

2 Functional part . . . . . . . . . . . . . . . . 2000104372

3 Stop ring. . . . . . . . . . . . . . . . . . . . . 2000104837

4 Installation kit comprising:

O-rings

Non-return valves

Grit filters . . . . . . . . . . . . . . . . . 2000105492

5 Aerator (PU with 10 pcs.). . . . . . . . 2000104691

Zubehör Best.-Nr.

Theft-resistant aerator

with flow-rate regulator

6 l/min . . . . . . . . . . . . . . . . . . . 2000101160

Special wrench for theft-resistant

aerator . . . . . . . . . . . . . . . . . . . 2000105960

1 Replacement kit for functional part

Rubber parts

Pressure spring

Circlip

Sealing plug

Grub screw. . . . . . . . . . . . . . . . . . 2000104785

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Franke Sanitärprodukte Handbücher

Franke

Franke AQUACONTACT AQCT0029 Bedienungsanleitung

Franke

Franke HEAVYDUTY HDTX815L Bedienungsanleitung

Franke

Franke F3 Series Bedienungsanleitung

Franke

Franke F5ST1001 Bedienungsanleitung

Franke

Franke Eos Neo Little Butler EOS-HC-304 Bedienungsanleitung

Franke

Franke SANW SANW212 Bedienungsanleitung

Franke

Franke MATRIX Produktinformationsblatt

Franke

Franke PROTRONIC-S PRTRS0013 Bedienungsanleitung

Franke

Franke F3SV1005 Bedienungsanleitung

Franke

Franke F5 F5EF3010 Bedienungsanleitung

Franke

Franke 7612210016837 Bedienungsanleitung

Franke

Franke Triflow Professional Trend Bedienungsanleitung

Franke

Franke AQUA205 Bedienungsanleitung

Franke

Franke F5E-Therm F5ET2009 Bedienungsanleitung

Franke

Franke F5E-Therm F5ET1013 Bedienungsanleitung

Franke

Franke 2030005623 Bedienungsanleitung

Franke

Franke STRX601 Bedienungsanleitung

Franke

Franke MIRANIT F5 Bedienungsanleitung

Franke

Franke F5 Series Bedienungsanleitung

Franke

Franke SIRIUS 2.0 S2D SLIM 611-62 Bedienungsanleitung

Franke

Franke ZSHOW0008 Bedienungsanleitung

Franke

Franke F5 Series Bedienungsanleitung

Franke

Franke MIRANIT F5ST2024 Bedienungsanleitung

Franke

Franke SIRIUS BS302 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema