Frontgate Holiday 68607 Bedienungsanleitung

7.5 ft

–ITEM

7.5 ft. Signature Balsam Fir Tree –Item 68607

PARTS LIST

A. BOTTOM

NUMBER OF PERSONS

RECOMMENDED FOR SKU 68607 –7.5’Signature Balsam Fir

2114TIPS STANDARDSTAND

B. MIDDLE

C. TOP

D. TREE STAND

ASSEMBLY: 2 U

1200LIGHTS

MAX DIAMETER 63”

HARDWARE

A. EXTRA BULBS AND FUSES QUANTITY EACH 18 PCS

1. Unpack:

Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the

tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its

branches (See Fig. 1A).

2. Basic Assembly Steps:

Fig. 1A

CAUTION: Two people may be needed to balance and assemble tree’s upper sections. Please use a

ladder, if needed, and follow all ladder safety instructions.

2.1 –Open the carton and take out all the contents. All contents that are listed in the section above on this

page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the stand to

form an “X” shape (See Fig 2A). Insert each of the three screws into the holes on the stand’s middle section,

being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree stand in

desired location.

Fig. 2A

2.2 –Locate Tree Section “A” and remove the protective caps that are on the top and bottom of the pole (they can be

replaced when you re-pack your tree). Insert Tree Section “A” into the tree stand. Make sure the pole is firmly inserted

into the stand, and then turn all three screws until contact is made with the pole. If Section “A” is not sitting straight,

then simply loosen the screws, adjust tree pole, and retighten the screws.

All the branches are connected to the tree’s center pole by metal hinges (See Figure 2). Remove the packing strap that is

around the tree section and allow the branches to fall into place.

2.3 –Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure section “B” is seated securely into

the top of section “A”. Remove the packing strap that is wrapped around this tree section, same as you for Section “A”.

Allow the branches and leaves to fall into place.

2.4 –Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure section “C” is seated securely

into the top of section “B”. Remove the packing strap that is wrapped around this tree section, same as you for Section

“B”. Allow the branches and leaves to fall into place.

3. Light Set and Power Connection:

3.1 –Your tree is lighted with Commercial grade miniature lights that are strung on the tree at the factory. Because your tree

is adorned with 1200 lights, to avoid overload of fuses within the tree, each section with the exception of the Tree Top

section is strung into a separate TREE SECTION EXTENSION CORD that is 8' in length. This 8' is to allow you to drop

this cord down to the bottom of the tree so it can plug into a power strip or multi tap extension cord. For your

convenience, each of these TREE SECTION EXTENSION CORDS has a built in foot pedal on/off switch so you can

turn each section on and off with a tap of your foot. Please note: Tied to the plug of each of these extension cords is a

red tag (see attached photo) which says "Please Plug Into Electrical Wall Outlet Only". This means that you should plug

each TREE SECTION 8' EXTENSION CORD either into a wall outlet, or into a power strip. This tag is trying to prevent

someone from plugging one TREE SECTION EXTENSION CORD into another TREE SECTION EXTENSION

CORD (this will blow a fuse in the extension cord).

3.2 –Your tree will include 2 foot pedals that will then plug into the wall or power strip. This will allow ease of turning your

lights on and off.

Unplug the extension cord plugs from electrical outlet on the wall. Take off all of your ornaments and tree

decorations before packing your tree back into its storage boxes.

Starting from the top, gently lift off each section. Each section should be packed away in the carton that it came in. Each

tree section should be turned upside down and then carefully press branches toward center pole for easier placement into

the storage box. Carefully place the tree in its box and tape it shut.

DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS

100ºF.

1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from ﬁre.

2. Please use water only for cleaning purpose.

3. When not in use, store neatly in a cool, dry locationprotected from sun light.

4. When the remote control has

malfunctioned,

please remove the power strip from the receiver and plug the power strip directly

into the wall.

THE FOLLOWING STEPS WILL HELPMAKEYOUR TREE LOOK MORE

REALISTIC

1. Light tree one section at a time as described in assemblyinstructions,so you can easily identify any bulbs that may be dislodged.

Push any loose bulbs back into their sockets.

2. Separate the branch tips to forma “V” shape and ﬂuff the needles. Make sure each tip is spread out and no two branches

are touching each other. For best access to branches, shape each section prior to adding the next section as described in

the initial assembly

instructions.

You may want to wear cotton gloves when ﬂufﬁng needles to avoid scratchesand skin

irritation.

3. Starting with the bottomrow, position the branches parallel to the ﬂoor. Angle the tips slightly upward like they are growing

towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to

hide the center of the tree.

4. Arrange the uppermostsection of the tree so that the tips are evenly spaced and pointing upward.

5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller appearance (The tree may be

shape differently(upswept /downswept /etc.) pending on one’s preference.)

STORAGE OF YOUR TREE

TROUBLE SHOOTING

TIPS

1. If entire tree lightingdoes not light, make sure power strip cords are securelyinserted in a working wall outlet.

2. If an entire sectionof the tree does not light, please review followingactions:

a. Check that all plugs within the tree are securely connected.

b. Check fuse in power strip to determine if it may need replacement.Caution: Note that a blown fuse indicates an

electrical overload or electrical short circuit. If the fuse is blown, unplug power strip fromoutlet.Also unplug any

additional strings or products may be attached to the power strip. Replace the fuse following

manufacturer

instructions with proper fuse rating. If the replacementfuse blows, a short circuit may be present and the product

should be discarded.

c. Check fuse in plug connectionon end of each light string.(See section on replacing plug fuses in this document).

3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit

up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement

light bulb (supplied by

manufacturer)

and follow directions in section describing how to replace light bulbsPORTANT

BASIC SAFETYINSTRUCTIONS

When using electrical products, to avoid risk of ﬁre burns, personal injury and electrical shock, basic precautionsshould always be

followed as stated below:

READ AND

ALL SAFETY INSTRUCTIONS

1. Do not use seasonalproducts outdoors unless marked suitable for indoor and outdoor use. When productsare used in outdoor

applications,connect the product to a Ground Fault Circuit interrupting(GFCI) outlet. If one is not provided, contact a qualiﬁed

electrician for proper installation.

2. This seasonal use product is not intended for permanent installationor use.

3. Do not mount or place near gas or electrical heaters, ﬁreplace, candles or other similar sources of heat.

4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

5. Do not let lamps rest on the supply cord or on any wire.

6. For your safety, unplugthe product when leaving the house, when retiring for the night or if left unattended.

7. This is an electrical product–not a toy! To avoid risk of ﬁre, burns, personal injury and electric shock it should not be played

with or placed where small children can reach

it.

8. Do not use this product for other than its intended use.

9. Do not hang ornaments or other objectsfromcord, wire or light string.

10.

Do not close doors or windows on the product or extensionscords as this may damage the wire insulation.

11. Do not cover the product with cloth, paper or any material not part of the product when in use.

12. This product is equipped with push-in lamps. Do not twist the lamps.

13. This product employsoverload protection(fuse). A blown fuse indicates an overload or short-circuitsituation. If the fuse blows,

unplugthe productfrom the outlet. Also unplug any additional strings or products that may be attached to the product. Replace

the fuse as per the user servicing instructions(follow product marking for proper fuse rating) and check the product. If the

replacementfuse blows, a short-circuit may be present and the product should be discarded.

14. Read and followall instructionsthat are on the product or provided with the product.

CAUTION: To reduce the risk of ﬁre and electric shock:

a. Do not install on trees having needles, leaves or branch coveringsof metal or materials which look like metal, and:

b. Do not mount or support strings in a manner that can cut or damage wire insulation.

USER

INSTRUCTIONS

TO REPLACE LIGHT BULBS

CAUTION: FIRST UNPLUGYOUR PRODUCT FROM ANY POWERSOURCE.

reduce

the

risk of

overheating,

replace burned-outlight bulbs promptly .Use only

2.5 volt light bulbs only.

2. Grasp plugand remove from the receptacle or any other electricaloutlet device. Do

not

unplugby pullingon the cord.

3. Pull the light bulb and itsattached plastic base straight out of light bulb holder.

4. Replace light bulb with only 2.5 volt

super

bright type light (provided with product).

the

new lamp base does not fit

the

replacementlight bulb, followthe steps

below before step

a. Remove the base of burned out lightby straightening light leads and gently pull bulb out.

b.Thread metal leads of new lamp throughhose in old base with one lead in each hold.

c. After lamp is fully inserted into

base

,bend each lead up, like other lights in the light set so that the leads

will

touch

the

contacts inside

the

light socket.

TOREPLACE A FUSE:

CAUTION:FIRST

UNPLUG

YOUR PRODUCTFROMANY POWER SOURCE.

1. Grasp plug and remove from the receptacleor other outlet device. Do not unplug

pulling on cord.

2. Open fuse cover. Slide open fuse access cover on top of attachment plugtowards plug's

metal

prongs

or blades.

FUSECOVER

SLIDES

FORWARD

3. Remove fuse carefully.

4. Risk of

fire.

Replace fuse

ONLY

with 3 Amp 120

Volt

fuse.(Provided with

product).

5. Close fuse

cover.

Return the sliding fuse

cover

back

to its former closed position

attachmentplug.

6. Risk of

fire.

Do not replace

attachment

plug

because

it contains

safety device (fuse)

that should not be removed.

Discard

product

if the

attachment

plug is

damaged

Please contact one of our

Product

Specialists for assembly assistance or questionsat 1-800-537-8484or email ps@frontgate.com.

Specialists are available weekdays 8:00 a.m.to 8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m.

7.5 ft

–ITEM

9 ft. Signature Balsam Fir Tree –Item 68609

PARTS LIST

A. BOTTOM

NUMBER OF PERSONS

RECOMMENDED FOR SKU 68609 –9’Signature Balsam Fir

3377TIPS STANDARDSTAND

B. MIDDLE

C. UPPER MIDDLE

D.TOP

E. TREE STAND

ASSEMBLY: 2 U

1700LIGHTS

MAX DIAMETER 68”

HARDWARE

A. EXTRA BULBS AND FUSES QUANTITY EACH 24 PCS

1. Unpack:

Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the

tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its

branches (See Fig. 1A).

2. Basic Assembly Steps:

Fig. 1A

CAUTION: Two people may be needed to balance and assemble tree’s upper sections. Please use a

ladder, if needed, and follow all ladder safety instructions.

2.1 –Open the carton and take out all the contents. All contents that are listed in the section above on this

page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the stand to

form an “X” shape (See Fig 2A). Insert each of the three screws into the holes on the stand’s middle section,

being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree stand in

desired location.

Fig. 2A

2.2 –Locate Tree Section “A” and insert Tree Section “A” into the tree stand. Make sure the pole is firmly inserted

into the stand, and then turn all three screws until contact is made with the pole. If Section “A” is not sitting straight,

then simply loosen the screws, adjust tree pole, and retighten the screws.

All the branches are connected to the tree’s center pole by metal hinges (See Figure 2). Remove the packing strap that is

around the tree section and allow the branches to fall into place.

2.3 –Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure section “B” is seated securely into

the top of section “A”. Remove the packing strap that is wrapped around this tree section, same as you for Section “A”.

Allow the branches and leaves to fall into place.

2.4 –Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure section “C” is seated securely

into the top of section “B”. Remove the packing strap that is wrapped around this tree section, same as you for Section

“B”. Allow the branches and leaves to fall into place.

2.5 –Locate Tree Section “D” and insert into the top of the Tree Section “C”. Make sure section “D” is seated securely

into the top of section “C”. Remove the packing strap that is wrapped around this tree section, same as you for Section

“C”. Allow the branches and leaves to fall into place.

3. Light Set and Power Connection:

3.1 –Your tree is lighted with Commercial grade miniature lights that are strung on the tree at the factory. Because your tree

is adorned with 1700 lights, to avoid overload of fuses within the tree, each section with the exception of the Tree Top

section is strung into a separate TREE SECTION EXTENSION CORD that is 8' in length. This 8' is to allow you to drop

this cord down to the bottom of the tree so it can plug into a power strip or multi tap extension cord. For your

convenience, each of these TREE SECTION EXTENSION CORDS has a built in foot pedal on/off switch so you can

turn each section on and off with a tap of your foot. Please note: Tied to the plug of each of these extension cords is a

red tag (see attached photo) which says "Please Plug Into Electrical Wall Outlet Only". This means that you should plug

each TREE SECTION 8' EXTENSION CORD either into a wall outlet, or into a power strip. This tag is trying to prevent

someone from plugging one TREE SECTION EXTENSION CORD into another TREE SECTION EXTENSION

CORD (this will blow a fuse in the extension cord).

3.2 –Your tree will include 3 foot pedals that will then plug into the wall or power strip. This will allow ease of turning your

lights on and off.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frontgate Haushaltsgeräte Handbücher

Frontgate

Frontgate 140149 Bedienungsanleitung

Beliebte Haushaltsgeräte Handbücher anderer Marken

Mesko

Mesko MS 9613 Bedienungsanleitung

Allied Moulded Products

Allied Moulded Products SLIDERBOX SBFB-1N Bedienungsanleitung

Coopers of Stortford

Coopers of Stortford F996 Bedienungsanleitung

Pella

Pella 802Q0101 Bedienungsanleitung

Ellia

Ellia aspire ARM-1210 Bedienungsanleitung

Project Source

Project Source 08-3843 Bedienungsanleitung

IKEA

IKEA VÄXER Bedienungsanleitung

impey

impey Aqua-Grade Linear Bedienungsanleitung

JML

JML DriBUDDI Bedienungsanleitung

ECODROP

ECODROP RV0813 Bedienungsanleitung

AquaPur

AquaPur Terry Bedienungsanleitung

pols potten

pols potten Taro in pot 540-300 Series Bedienungsanleitung

AeroBed

AeroBed Premier IntelliWarmth Bedienungsanleitung

Allen + Roth

Allen + Roth WSWS-WB1 Bedienungsanleitung

AEG

AEG MWTK60 Bedienungsanleitung

Sunbeam

Sunbeam heated bedding Bedienungsanleitung

Nokia

Nokia Nokia Sleep Bedienungsanleitung

Velleman

Velleman XMCL12 Bedienungsanleitung