Fujitsu fi-5650C Konfigurationshandbuch
1
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
fi-5650C & fi-5750C CONSUMABLE
REPLACEMENT AND CLEANING INSTRUCTIONS
CG00000-707601 RevisionC
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
2
PickRollersQty3
Brake Roller
Qty 3
Cleaning Paper
Qty 1 10/pack
Cotton Swabs
Qty 1 100/pack
F1 Cleaner
IsopropylAlcohol Qty 1
Lint Free
Cleaning Cloths
Qty 2 20/pack
KIT CONTENTS
Note:Quantitymay vary
3
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CONSUMABLES LIST
Description Qty Life Fujitsu P/N
Brake Roller 1 250,000 PA03338-K010
Pick Rollers 1 250,000 PA03338-K011
Note:
NCRorCarbonlesspaperhaschemicalcomposition which damages
the Brake Roller and Pick Rollers. Cleaning of these items will be
neededmorefrequentlytoavoidfeedproblemsifscanningalarge
quantity of this type of paper. Also the consumable life will be reduced
if this paper is scanned.
PickRollers
Brake Roller
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
4
REPLACING THE BRAKE ROLLER
• Whentheconsumableshave
fed250,000pagesthe
message to the right is
displayedonthecomputer
screen.
• Removeanydocuments
remainingintheADFPaper
Chute.
• Press the ADF Buttons to
release the lock and open the
ADF.
• OpentheBrakeRollerCover.
Aworn out or improperlyinstalledBrake Roller will cause multiplefeedsor
paperjams. The Brake Roller has anapproximatelifeof250,000 pages. If
NCR or carbonless paper is scanned the life span of the Brake Roller may
be decreased by as much as 50%.
Note:
It is very strongly recommended to replace the Brake Roller and Pick
Roller at the same time. This will insure the longest possible life for
eachconsumableitem.
IftheBrakeRoller and Pick Roller have been cleaned (refer tothe cleaning
section of this document) they should be replaced if the scanner continues
to multi-feed or jam paper at a high rate.
ADF Buttons
Brake Roller Cover
Brake Roller Cover
5
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE BRAKE ROLLER (CONT.)
• Lift the Brake Roller out of the
scanner.
• Pull the shaft out of the Brake
Roller.
• Install the shaft into the new
BrakeRoller.
Slots in Brake Roller Collar
Note:
When installing the shaft into the new Brake Roller, make sure to align
the tabs in the roller shaft with the slots on the collar of the Brake
Roller. Referto thephotosbelow.
Tabs in Brake Roller Shaft
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
6
REPLACING THE BRAKE ROLLER (CONT.)
• Placethe new Brake Roller
intotheBrakeRollerCover,
making sure to align the flat
areaoftheBrake Roller shaft
intheguidegrooveofthe
BrakeRollerCover.
Note:
It is important to make sure that the shaft is at the bottom of the guide
grooveoftheBrake RollerCover.
• Close the Brake Roller Cover, making sure it snaps into place.
• Close theADF.
• Referto“ResettingTheConsumablesCounters” later in this document
toreset the Brake Roller Counter.
7
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE PICK ROLLERS
Worn out, defective, or improperly installed Pick Rollers will cause mis-
feedsandpaper jams. The Pick Rollers have an approximatelifeof
250,000pages. If NCR orcarbonlesspaperis scanned, the lifespanof
the Pick Rollers will be decreased by as much as 50%.
Note:
It is very strongly recommended to replace the Brake Roller and Pick
Roller at the same time. This will insure the longest possible life for
eachconsumableitem.
IftheBrakeRoller and Pick Roller have been cleaned (refer tothe cleaning
section of this document) they should be replaced if the scanner continues
to multi-feed or jam paper at a high rate.
• Removeanydocuments
remainingintheADFPaper
Chute.
• Press the ADF Buttons to
release the lock and open the
ADF.
• Slideopen the Sheet Guides
onthePaper Chute, making
sure that they do not obstruct
thePickRollerCover.
• OpenthePickRollerCover.
• Slide the two Pick Rollers in
thedirectionofthe arrow and
lift them out of the scanner.
Note:
ThePickRollers are made
upof two rollers. The roller
with the treads going across
theroller is the Separation
Roller. Theroller withthe
belt in the center is the Pick
Roller.
Separation Roller
Pick Roller
ADF Buttons
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
8
REPLACING THE PICK ROLLERS (CONT.)
• InstallthenewSeparation
Roller onto the shaft. Make
sure to align the slot in the
roller collar with the screw in
theshaft.
• Install the new Pick Roller
onto the shaft.
Make sure belt is facing up.
• Make sure to align the slot in the roller collar with the screw in the
shaft.
• ClosethePickRollerCover.
• Close theADF.
• Referto“ResettingTheConsumablesCounters” later in this document
to reset the Pick Roller Counter.
Note:
Make sure that the belt is facing up and the wide plastic foot slides
intothegroove in the bottom oftherollercompartment.
Wide Plastic Foot
Groove
9
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
RESETTING THE CONSUMABLE COUNTERS
After the Brake Roller and the Pick Rollers have been replaced it is
important to reset the scanner consumable counters. These counters will
keep track of how many pages have been scanned since the last time the
consumableswerereplaced. Resetting these counters will insure that
the Brake Roller and the Pick Rollers are replaced before paper feed
problemsoccur.
• Confirm that the scanner and the PC are connected, and the scanner is
poweredon.
• Select [PROGRAMS] - [SCANNER UTILITY FOR MICROSOFT WINDOWS]-
[SOFTWARE OPERATION PANEL]from the [START] Menu.
• The screen to the right is
displayeduponenteringthe
SoftwareOperationPanel.
•Press the DEVICE SETTING tab.
fi-5650C&fi-5750CCONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
10
RESETTING THE CONSUMABLE COUNTERS (CONT.)
• TheDeviceSettingScreento
the right is displayed.
• Press the CLEAR button next
to the consumable that has
beenreplaced.
• The screens to the right are
displayedafterpressingthe
correspondingClearbutton.
Press the YES button to
confirmtheresetting of the
Brake Roller or Pick Roller
Counter.
• When the screen to the right
is displayed, press the OK
button.
• Press the OK button when
asked to “Write to EEPROM
OK?” This will reset the
counterandexitthe Software
OperationPanel.
Andere Handbücher für fi-5650C
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Fujitsu Scanner Handbücher
Fujitsu
Fujitsu ScanSnap Bedienungsanleitung
Fujitsu
Fujitsu ScanSnap S1300i Bedienungsanleitung
Fujitsu
Fujitsu M4099D Konfigurationshandbuch
Fujitsu
Fujitsu C150-E140-03EN Bedienungsanleitung
Fujitsu
Fujitsu M3092DC Bedienungsanleitung
Fujitsu
Fujitsu ScanSnap S500 Bedienungsanleitung
Fujitsu
Fujitsu PA03768-B005 Handbuch
Fujitsu
Fujitsu ScanSnap fi-5110EOX Bedienungsanleitung
Fujitsu
Fujitsu fi 5750C - Document Scanner Bedienungsanleitung
Fujitsu
Fujitsu FI-5900C Bedienungsanleitung
Fujitsu
Fujitsu Scan Partner 300C Bedienungsanleitung
Fujitsu
Fujitsu FI 4220C - Document Scanner Bedienungsanleitung
Fujitsu
Fujitsu M3097E Plus Handbuch
Fujitsu
Fujitsu FI-6130 Konfigurationshandbuch
Fujitsu
Fujitsu M3096EX Konfigurationshandbuch
Fujitsu
Fujitsu FI-5900C Konfigurationshandbuch
Fujitsu
Fujitsu ScanSnap S1100 Handbuch
Fujitsu
Fujitsu M3091DC Bedienungsanleitung
Fujitsu
Fujitsu FI-6130 Bedienungsanleitung
Fujitsu
Fujitsu ScanSnap S500 Handbuch
Beliebte Scanner Handbücher anderer Marken
Infinite Peripherals
Infinite Peripherals INFINEA TAB M Bedienungsanleitung
Mustek
Mustek PageExpress 4800 Pro Bedienungsanleitung
Optex
Optex 750830 Bedienungsanleitung
Innova
Innova 5210 Bedienungsanleitung
Visioneer
Visioneer CardReader 100 Kurzanleitung
Rohde & Schwarz
Rohde & Schwarz TSME6 Bedienungsanleitung