Fujitsu PRIMERGY 870 Bedienungsanleitung
U41029-J-Z146-1-7400 English - 1
Introduction
This Technical Manual describes the system boards of the PRIMERGY 870 server systems, which
can be equipped with up to four Intel Xeon processors.
You may find further information in the description "BIOS Setup".
Further information to drivers is provided in the readme files on hard disk or on the supplied drivers
diskettes or on the "Drivers & Utility" or "ServerStart" CD.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
!Pay particular attention to texts marked with this symbol. Failure to observe this warning
endangers your life, destroys the system, or may lead to loss of data.
iThis symbol is followed by supplementary information, remarks and tips.
²
Texts which follow this symbol describe activities that must be performed in the order shown.
Texts in italics indicate commands or menu item.
"Quotation marks" indicate names of chapters and terms that are being emphasized.
Overview
The PRIMERGY 870 server systems mainly consist of the following plug-in boards:
• I/O board
• Processor board
• Memory board (2x)
• Interface board
• SCSI board (3x)
• Power supply board
• ECU board
• Drive board (2x)
Introduction Abbreviations
2 - English U41029-J-Z146-1-7400
Abbreviations
ASIC Application Specific Integrated Circuit
ASR&R Automatic Server Recovery & Restart
BIOS Basic Input Output System
CAN Controller Area Network (CAN-Bus)
CPU Central Processing Unit
DAC Disk Array Controller
DIMM Dual Inline Memory Module
DIP Dual Inline Package
DMA Direct Memory Access
ECU Environment Control Unit
EDO-DRAM Enhanced Data Output Dynamic Random Access Memory
FPM Fast Page Mode
I2O Intelligent Input Output
IDE Integrated Drive Electronics
ISA Industry Standard Architecture
ISP In-System Programmable
LAN Local Area Network
LCD Liquid Crystal Display
LED Light-Emitting Diode
LVD Low Voltage Differential
MINT Multiprocessor Interrupt (Controller)
OLR On-Line Replaceable
PIIX4 PCI/ISA Bridge and IDE Accelerator
PCI Peripheral Component Interconnect
PIO Programmed Input Output
PXB PCI Expander Bridge
RTC Real Time Clock
RTDS Remote Test and Diagnostic System (RemoteView)
SAF-TE SCSI Accessed Fault-Tolerant Enclosure
SCA Single Connected Attachment
SCSI Small Computer System Interface
SE Single Ended
STM SAF-TE Terminator Module
USB Universal Serial Bus
VGA Video Graphics Array
Abbreviations Important notes
U41029-J-Z146-1-7400 English - 3
Important notes
Store this manual close to the device. If you pass on the device to third parties, you should also
pass on this manual.
!Be sure to read this page carefully and note the information before you open the Server.
Please note the information provided in the chapter "Safety" in the Operating Manual of
the server.
Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore
essential to observe the instructions in the chapter "I/O board" - "Replacing the lithium
battery".
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer (CR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in accordance with
local regulations concerning special waste.
Connecting cables for peripherals must be adequately insulated to avoid interference.
!Components can become very hot during operation. Make sure you do not touch
components when making extensions to the boards. There is a danger of burns!
iThe warranty expires if the device is damaged during the installation or replacement of
system expansions. Information on which system expansions you can use is available
from your sales office or the customer service.
Boards with electrostatic sensitive devices (ESD) may be identified by labels.
When you handle boards fitted with ESDs, you must observe the following points under all
circumstances:
• You must always discharge yourself (e.g. by touching a grounded object) before working.
• The equipment and tools you use must be free of static charges.
• Pull out the power plug before inserting or pulling out boards containing ESDs.
• Always hold boards with ESDs by their edges.
• Never touch pins or conductors on boards fitted with ESDs.
I/O board Abbreviations
4 - English U41029-J-Z146-1-7400
I/O board
Features
• Intel Chipset 82450NX
• 512 Kbytes Flash BIOS
• Intel i960 processor for PCI-to-PCI-Bridge, I2O and Server Management
• Intel 82527 CAN controller
• Intel 82558 Fast Ethernet LAN controller
• two Symbios 53C875 Ultra Wide SCSI controller
• Cirrus CL-GD5446 graphics controller with 2 Mbyte video memory
• IDE hard disk controller connected to PCI bus for up to two IDE drives
ultra DMA33 mode capable, supports PIO modes 0-4
• Real-time clock/calendar with integrated battery backup
• Floppy disk controller (up to 2.88 Mbytes format)
• four 64 bit hot-plug PCI slots
• four 32 bit hot-plug PCI slots
• two 32 bit PCI slots (one slot shared)
• four ISA slots (three slots shared)
• two 32-bit PCI slots over i960 processor (both shared)
• PS/2 mouse port
• PS/2 keyboard port
• four external serial ports
• USB (Universal Serial Bus)
• CAN bus
• LAN port
• Cover detection
• Remote On possible via modem, via internal fax modem and via the four external serial ports
• Wake On LAN
Interfaces and connectors I/O board
U41029-J-Z146-1-7400 English - 5
Interfaces and connectors
1
2
3
4
5
6
8
9
11
13
7
14
12
15
10
1
2
3
4
6
5
7
8
9
10
11
12
13
12
11
10
1 = SCSI 1 16 bit
2 = SCSI 2 16 bit
3 = Cover detection
4 = ECU
5 = ISP
6 = Floppy disk drive
7 = IDE power supply
8 = IDE drives
9 = Hot-plug PCI panel for 64 bit slots
10 = Hot-plug PCI panel for 32 bit slots
11 = Keyboard and mouse
12 = USB
13 = LAN
14 = Remote On (Fax modem / Internal Modem
On)
15 = Wake up on LAN
I/O board Possible screen resolution
6 - English U41029-J-Z146-1-7400
Possible screen resolution
Depending on the operating system used the screen resolutions in the following table refer to the
screen controller on the I/O board. If you are using an external screen controller, you will find details
of supported screen resolutions in the Operating Manual or Technical Manual supplied with the
controller.
Screen resolution Refresh rate (Hz) Horizontal-
rate (kHz) ** Max. number of colors
640x350 70 31,5 16
640x350 84 38 16
640x480 60 31,5 16777216
640x480 75 37,5 16777216
640x480 85 43,4 16777216
640x480 100 50,6 16777216
720x400 70 31,5 16
720x400 84 38 16
800x600 60 38 65536
800x600 60 38 16777216
800x600 72 48 65536
800x600 72 48 16777216
800x600 75 47 65536
800x600 75 47 16777216
800x600 85 53,7 65536
800x600 85 53,7 16777216
800x600 100 63 65536
800x600 100 63 16777216
1024x768 87 interlaced 36 256
1024x768 87 interlaced 36 65536
1024x768 60 48,4 256
1024x768 60 48,4 65536
1024x768 75 60 256
1024x768 75 60 65536
1024x768 85 68,7 256 *
1024x768 100 81 256 *
1280x1024 87 interlaced 49 16
1280x1024 87 interlaced 49 256
1280x1024 60 63,7 256 *
1280x1024 75 80,4 256 *
* no 16 color mode
** The horizontal rate values may have a tolerance range of ± 0.3 kHz.
Settings with the switch block I/O board
U41029-J-Z146-1-7400 English - 7
Settings with the switch block
OFF
ON
12345678
1
2
3
4
6
5
7
8
9
10
11
12
13
12
11
10
Switch 1 to 5 = not used
Switch 6 = Write protection for floppy disks Switch 7 = Skipping password query
Switch 8 = Recovering system BIOS
I/O board Settings with the switch block
8 - English U41029-J-Z146-1-7400
Write protection for floppy disks - switch 6
Switch 6 is used to define whether floppy disks can be written or deleted in the floppy disk drive. To
write and delete floppy disks, the write -protection in BIOS setup must be disabled (in menu Security,
the field Diskette Write must be set to Enabled).
on The floppy disk drive is write-protected.
off Read, write and delete floppy disks is possible (default setting).
Skipping the password query - switch 7
Switch 7 is used to define whether the password is queried at system startup, if the password
protection is enabled in BIOS Setup (in Security menu , the Password field must be set to Enabled).
on The password query is effective.
off The password query is skipped (default setting).
Recovering System BIOS - switch 8
Switch 8 enables recovery of the old system BIOS after an attempt to update has failed. To restore
the old system BIOS you need a Flash BIOS Diskette (please call our customer service).
on The system boots from the "Flash BIOS floppy disk" from Drive A and reprograms
the system BIOS on the I/O board.
off The system is started with the system BIOS on the I/O board. The system BIOS
cannot be reprogrammed. (Default setting)
Add-on modules I/O board
U41029-J-Z146-1-7400 English - 9
Add-on modules
1
2
3
4
6
5
7
8
9
10
11
12
13
12
11
10
1
2
3
6
4
5
9
8
7
7
9
10
1 = Battery
2 = Slots for i960 memory (odd)
3 = Slots for i960 memory (even)
4 = Flash BIOS
5 = Interface board
6 = ISA slots
7 = 32 bit PCI slots (bus 1-i960)
8 = 32 bit PCI slots (bus 0-0A)
9 = 32 bit Hot-plug PCI slots (bus 2-0B)
10 = 64 bit Hot-plug PCI slots (bus 3-1A)
All PCI slots have bus master capability.
I/O board Add-on modules
10 - English U41029-J-Z146-1-7400
Memory extension for i960
The I/O board is equipped with two installation banks (even and odd) for memory modules. Both
memory banks can be equipped with single-sided or double-sided memory modules. Equipping
must begin with the even installation bank.
The board supports a maximum of 16 Mbytes.
Only the combination possibilities listed in the following table are permitted.
Even Bank Odd Bank Maximum memory
configuration
4 Mbyte single-sided no memory module 4 Mbyte
4 Mbyte single-sided 4 Mbyte single-sided 8 Mbyte
8 Mbyte double-sided 8 Mbyte double-sided 16 Mbyte
Equipping sequence/slot priority
Equip the slots according to the following table. Go through the table from top to bottom. The priority
decreases from top to bottom.
Board Slot
12345678910 11 12 13
PCI screen controller* 1. 1.
PCI DAC (one) 1.
64 bit PCI controller 1. 2. 3. 4.
PCI DAC (several) 2. 4. 6. 1. 3. 5.
ISA controller 4. 3. 2. 1.
32 bit PCI controller (other) 2. 3. 5. 7. 1. 4. 6. 8. 10. 9. 12.
*: The PCI screen controller must be inserted in either slot 9 or slot 10.
Inhaltsverzeichnis
Andere Fujitsu Server Handbücher
Fujitsu
Fujitsu SPARC Enterprise T5140 Bedienungsanleitung
Fujitsu
Fujitsu SPARC Enterprise T5120 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY RX100 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY TX2550 M5 Bedienungsanleitung
Fujitsu
Fujitsu SPARC Enterprise T5440 Server Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY TX150 S8 Benutzerhandbuch
Fujitsu
Fujitsu PRIMERGY CX272 S1 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY TX100 S2 Betriebsanleitung
Fujitsu
Fujitsu PRIMERGY RX200 S7 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY GX2460 M1 Bedienungsanleitung
Fujitsu
Fujitsu SPARC M12 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY S60 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY RX100 S6 Bedienungsanleitung
Fujitsu
Fujitsu Primergy TX120 Bedienungsanleitung
Fujitsu
Fujitsu BS2000 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY RX300 S7 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY BX922 S2 Bedienungsanleitung
Fujitsu
Fujitsu Primergy CX270 S2 Bedienungsanleitung
Fujitsu
Fujitsu PRIMERGY TX200 S2 Bedienungsanleitung
Fujitsu
Fujitsu Server PRIMERGY TX1330 M1 Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung