Fujitsu Primergy TX300 S4 Bedienungsanleitung

2Installing the server into the rack

The procedure for installation to the server into the rack is explained here.

The left or the right in this manual is dened when the rack is viewed from the front.

- Be sure to secure the rack with stabilizers to prevent the device from tipping over. For details on installing the rack, refer to the

manual provided with the rack.

- The weight of the server exceeds 35kg. When you carry the server, make sure more than three people do it to secure the

right and left sides and the bottom of the body.

1Open both the front and rear doors of

the rack.

2Check where to attach the slide rail and

rack nuts.

As seen in the gure below, the base surface of the

server must be positioned at where the intervals

between the rack bracket holes are narrow.





3Attach M5 rack nuts.

Use 4U per device. Insert the latches of the rack nuts

from the inside of the rack bracket into 2nd and 11th

holes (counting from the position where the server is

installed) to attach the rack nuts.













 



1Check all of the Rackmount kit items

The rackmount kit for installation into a rack is supplied with the server. First check that none of the

following items are missing. If any items are missing or defective, contact an ofce listed in the "Contact

Information" of the "Start Guide".

□Slide rail : 1 pair









□M3 Flathead screw : 4 □M5 Flathead screw : 2

□Washer : 2 □M5 Rack nut : 4













B7FH-5341-01EN Z0-00

TX300 S4

4Fix the slide rails to the rack.

Fix the rear side rst.

Secure them by inserting the pins of the slide rail to the

rst and the third hole of the slide rail. For the front

side, secure the slide rail to the rack at the third hole

using a washer and M5 athead screw.















The slide rails are designed as both dedicated left

and right side. Fix the slide rails with facing up the

indication of "LEFT" and "RIGHT ".

The rail may be damaged if server is installed on

the rack whose slide rails are xed oppositely.

5Pull the inner rails toward the front until

they click into place.



6Draw out the inner rails, and attach the

inner rail to the server.

Put the server on so that the ledge parts in the inner

rail may put it in the ditch on the server side.

2. Slide the server towards the back until the screw

hole in the inner rails and the screw hole in the

server side overlap.

Fix the inner rail and the server with the M3 athead

screws (Fix each side with two screws).









7Install the server into the rack.

Hold the locks on the right and left of the slide rail

pressed and slide the server even further into the rack.



Be careful not to pinch your ngers or catch any

clothing when sliding the server into the cabinet.

Failing to do so may cause injuries.

8Fix the server to the rack.

Fix them by using the four M5 thumbscrews.



3Connecting peripheral devices after installing the server

into the rack

Connect peripheral devices after installing the server into the rack. Use long enough cables because

you may pull the server from the rack when necessary.

nFixing the power cable

To prevent the power cable from falling down, after connecting the power cable to the server, pass the supplied release tie

through the air holes and secure approximately 10 cm from the connector of the cable as seen in the gure below. When

unplugging the cable, make sure to unplug the connector on the server end.







Surely unplug the power connector at the server end when necessary.

nCable forming process

After connecting the peripheral devices, tie all the cables and x them with the release tie to the cable holder provided with

the rack. This forming process makes the cables easily recognizable even when multiple servers are installed in the rack.











Andere Handbücher für Primergy TX300 S4

Inhaltsverzeichnis

Andere Fujitsu Server Handbücher

Fujitsu

Fujitsu PRIMERGY CX2550 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY H200 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX300 S5 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX600 S3 Bedienungsanleitung

Fujitsu

Fujitsu Primergy BX620 S2 Kurzanleitung

Fujitsu

Fujitsu primergy h250 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX600 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX150 S8 Bedienungsanleitung

Fujitsu

Fujitsu SPARC ENTERPRISE T5220 Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX100 S4 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX200 S6 Bedienungsanleitung

Fujitsu

Fujitsu HX2560 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX100 S8 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX300 S5 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX2530 M4 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY GX2560 M7 Bedienungsanleitung

Fujitsu

Fujitsu SPARC Enterprise T2000 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Bedienungs- und Wartungsanleitung

Fujitsu

Fujitsu SPARC Enterprise T5140 Bedienungsanleitung

Fujitsu

Fujitsu teamserver M851i Bedienungsanleitung

Fujitsu

Fujitsu FUTRO S550 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX200 S6 Bedienungsanleitung

Fujitsu

Fujitsu Primergy RX200 S4 Leitfaden

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung