GarrettCom Magnum 4K220 Bedienungsanleitung

www GarrettCom com

Corporate Headquarters

GarrettCom, Inc.

213 Hammond Ave.

Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email [email protected]

Magnum 4K-Series

4K Switches

Installation and User Guide

= X

UPLINK

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39

115-230V~ 50/60 Hz

(-) GND (+)

48V DC = X

UPLINK

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39

Power

Col/FDX Col/FDX

Magnum 4K220R-Series

Ethernet 10/100 Switch

100M

Col/FDX

Link/Act

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

Magnum



4K-Series

4K220 Switches

Installation and User Guide

Part #: 84-000094 (Rev D)

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is

a registered trademark of GarrettCom, Inc.

Important: The Magnum 4K220 Switches contains no user serviceable

parts. Attempted service by unauthorized personnel shall render all

warranties null and void. If problems are experienced with the Magnum

4K Switches, consult Section 6, Troubleshooting, of this User Guide.

of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed

below:

GarrettCom, Inc.

47823 Westinghouse Drive

Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email [email protected]

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if

not installed and used properly, that is in strict accordance with the manufacturer's

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when operated in a

commercial environment. Operation of this equipment in a residential area is

likely to cause interference, in which case the user at his own expense will be

required to take whatever measures may be required to correct the interference.

Magnum 4K220 Switches Installation and User Guide (10/04)

iii

www GarrettCom com

TABLE OF CONTENTS Page

1.0

SPECIFICATIONS................................................................................1

1.1

ECHNICAL

PECIFICATIONS

.................................................................1

2.0

INTRODUCTION..................................................................................3

2.1

NSPECTING THE

ACKAGE AND

RODUCT

............................................3

2.2

RODUCT

ESCRIPTION

AGNUM

4K220CR

WITCHES

....................4

2.2.1

Magnum 4K220 Switch chassis ...................................................4

2.2.2:

Magnum 4K220CR “Reverse” model,.........................................5

2.2.3

Up-link port #39 for Cascading....................................................6

2.2.4

4K220C, 10/100 F/H dual-speed switched ports,.........................6

2.2.5

Frame Buffering and Latency.......................................................6

2.3

EATURES AND

ENEFITS

......................................................................9

2.4

PPLICATIONS

.....................................................................................10

3.0

INSTALLATION................................................................................11

3.1

OCATING

AGNUM

4K220

WITCHES

..............................................11

3.2

ONNECTING

THERNET

EDIA

.........................................................12

3.2.1

Connecting Twisted Pair ............................................................12

3.3

OWERING THE

AGNUM

4K220CR

WITCH

.....................................12

3.4

ACK

MOUNTING

..................................................................................13

4.0

OPERATION........................................................................................14

4.1

WITCHING

UNCTIONALITY

...............................................................14

4.2

TATUS

LED

.....................................................................................15

4.3

LINK

ORT

FOR

RJ-45

ORT

#39

(

ONLY

) ......................................15

4.4

UTO

NEGOTIATION FOR

RJ-45

(

COPPER

)

PORTS

................................15

4.5

UTO

NEGOTIATION

FULL

DUPLEX MODE

..........................................16

4.6

LOW

CONTROL

IEEE

802.3

X STANDARD

..........................................17

5.0

TROUBLESHOOTING.......................................................................17

5.1

EFORE

ALLING FOR

SSISTANCE

....................................................18

5.2

HEN

ALLING FOR

SSISTANCE

.......................................................18

5.3

ETURN

ATERIAL

UTHORIZATION

(RMA)

ROCEDURE

.................19

5.4

HIPPING AND

ACKAGING

NFORMATION

..........................................20

APPENDIX A: WARRANTY INFORMATION .........................................20

APPENDIX B : INTERNAL DC POWER SUPPLY OPTION...................21

APPENDIX C: INTERNAL DC DUAL-SOURCE POWER OPTION......24

EVISIONS

Rev D 10/04: edited minor update

Rev D 04/02: Updated Rack-mounting and Appendix B & C with 24VDC

and 125VDC Power Supply option

Rev C 05/01: Modify for 4K220CR specifications

REV B 04/01 : Change the company name to GarrettCom, Inc. (Formerly

it was Garrett Communications). There are no changes to the content of

the material at this time.

Rev A 03/00 : This revision is the initial release of the 4K Switch user

manual.

Magnum 4K220 Switches

Installation and User Guide (10/04)

www GarrettCom com

The Magnum Line

ETHERNET CONNECTIVITY PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

OVERVIEW

GarrettCom, Inc. offers the premium-quality Magnumline of Ethernet LAN

connectivity products with industry-standard functionality and built-in fiber

configurability. Magnum products are designed for use in demanding Carrier Class,

Industrial Grade and OEM applications where reliability is a primary consideration.

4K-Series Switches, 100 & 10Mbps, copper ports with optional fiber

port, with auto-negotiating full switching performance

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper

ports, mixed-speed and mixed-media types, full switching

performance

“Outdoor” Ethernet Switch, for temperature uncontrolled locations

6 10/100 and 2 100Mb fiber ports, can be connected in strings

Mixed-Media Fiber Hub, 16-port Stackable, 10/100 auto-sensing

Dual Speed 8-port and 16-port Stackables, 10/100 auto-sensing

Stackable Hubs, SNMP Optional

10Mb series and 100Mb series, both w/ optional port modules

Personal Switches

, 10/100Mb

8 port dual speed, Auto-negotiable with fiber option

Personal Hubs

, 100Mb or 10/100Mb

8-port, with two switched ports (1 fiber built in)

Personal Hubs, 10Mb series

8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.

Media Converters, 10Mb and 100Mb series

All media combinations, incl. fiber ST, SC, mm., single mode

The “X-line” of configurable Mi

ed Media products:

Stackable Concentrators, SNMP optional, 13-Ports

Mini-Concentrators, 7 Ports, Repeaters, 2-Ports

Repeater Port Modules (RPMs),6 types for Ethernet media

Bridge Port Modules (BPMs), 4 types, for segment isolation

Fan-Outs, 10Mb series

2, 4 and 8 Port Models

Transceivers, 10Mb and 100Mb series 10Mb Mini-Transceivers

and Coax Models, All Types Oct, 04

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

1.0 SPECIFICATIONS

1.1 Technical Specifications

Performance

Aggregate Filtering Rate: 3M pps within each 20 port bank (all ports

100Mbps speed), 298K pps between port banks, 6M pps for all 40 ports

(all ports are wire speed)

Aggregate Forwarding Rate:(for Magnum 4K-Series Fast Ethernet ports)

(all ports are wire speed) 14.4M frames per second, 40-port units

Data Rate: 10 Mbps and 100Mbps

Address Table Capacity: 4K node addresses, self-learning with

address aging

Packet buffer size : 2 MB dynamic

Latency: 5 s + packet time (100 to 100Mbps)

15 s + packet time (10 to 10 Mbps, and 10 to 100Mbps)

PDV: 50BT

Network Standards

Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,

IEEE 802.3u: 100BASE-TX, 100BASE-FX

Maximum 10 Mbps Ethernet Segment Lengths

Unshielded twisted pair - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

10BASE-FL multi-mode fiber optic - 2 km (6,562 ft)

10BASE-FL single-mode fiber optic - 10 km (32,810 ft)

Maximum Standard 100Mb Fast Ethernet Segment Lengths:

10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

Shielded twisted pair - 150 m (492 ft)

Connectors for copper wiring

Twisted Pair at 10/100Mb: RJ-45 shielded, female, front mounted

(for Magnum 4K-Series Fast Ethernet copper ports, use Cat 5 cable)

Manual switch-selections and jumpers

Fiber default: Full-duplex (Manual DIP switch settings inside of the chassis

can select each of fiber ports to HDX mode. DIP switch SW4 controls fiber

port # 2, whereas DIP switch SW6 controls fiber port #4. Down position will

sets half-duplex, up position (default) sets full-duplex).

Copper default: Auto-negotiation

LEDs: Per Port

LK/Act: Steady ON for Link with no traffic, blinking indicates port is

transmitting and receiving

FDX/Col: ON = Full-Duplex Mode

BLINKING = Half-Duplex Collision

100/10: ON = 100Mbps speed

OFF = 10 Mbps

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

Operating Environment

Ambient Temperature: 32to 120F (0to 50C)

Storage Temperature: -40to 160F (-40to 70C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 13000ft (-60 to 4000m)

Conformal coating option: Request quote

Packaging

Enclosure: Rugged High strength metal. Suitable for stand-alone or

rack-mounting

Dimensions: 1.75 in H x 17.0 in W x 9.0 in D

4.45cm H x 43.2cm W x 22.9cm D

Weight: 7.1 lb. (3.2 Kg) rack-mount models

Cooling method: Fan cooled, @ 7 cfm

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis,

with adjacent manual ON-OFF switch (on AC models only)

Input Voltage: 110 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 28 watts typical

35 watts max

Power Supply Rating: 3Amps at 5VDC

DC Power Supply (Options)

-48VDC Power Input Voltage : 36 to 72 VDC (auto ranging)

24VDC Power Input Voltage : 20 to 40VDC

125VDC Power Input Voltage : 120 to 160VDC

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

For Dual Source and Redundant DC for –48VDC, 24VDC Power &

125VDC supply options (Optional), see Appendices.

Agency Approvals

UL listed (UL1950), cUL, CE

Emissions meet FCC Part 15 Class A

Warranty

Three years, return to factory Made in USA

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

2.0 Introduction

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage that you believe occurred during shipment or

delivery. Inspect the contents of this package for any signs of damage and ensure that

the items listed below are included.

This package should contain:

1 Magnum 4K220CR Switch

1 AC Power Cord (U.S. and other 115 VAC only)

1 Set of metal “Ears” for standard 19” rack mounting

1 Installation and User Guide (this manual)

1 Product Registration Card

Remove the items from the shipping container. Be sure to keep the shipping

container should you need to re-ship the unit at a later date. To validate the product

warranty, please complete and return the enclosed Product Registration Card to

GarrettCom, Inc. as soon as possible.

In the event there are items missing or damaged, contact the party from whom

you purchased the product. If the unit needs to be returned, please use the original

shipping container if possible. Refer to Section 6, Troubleshooting, for specific return

procedures.

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

2.2 Product Description - Magnum 4K220CR Switches

Magnum 4K220CR Switches boost the performance of large Ethernet LANs,

with economical solution per switched port. The Magnum 4K220’s provide the

switching speed and the reliability to support multiple workgroups, each with its own

switched 100Mbps or 10Mbps domain, for increased network performance.

Designed specifically for the vertical rack space environment, the Magnum

4K220CR used in departments with multiple workgroups, in remote offices and in

network traffic centers or multi-system power users, the Magnum 4K220CR witches are

easy to install and use. Addresses of attached nodes are automatically learned and

maintained, adapting the switching services to network changes and expansions. Front-

mounted LEDs provide status information on each port. The Magnum 4K-Series

Switches provide high performance plug-and-play operation in convenient rack-mount

packages.

The reverse port enclosure of Magnum 4K220CR switches are designed to

provide ease of maintainability to the larger network. The 40-port density in a 1U rack

mount “reverse” package is obtained by dedicating the front of the unit to the LED

indicators, and the rear side of the unit to wiring and power supply connection.

The Magnum 4K220CR switches are non-blocking on all ports and include

2MB dynamic packet buffers and a 4K-node address table for advanced performance as

well as to support large networks. The Magnum 4K-Series Switches, with store-and-

forward switching, filter all faulty packets to minimize traffic congestion.

The Magnum 4K220CR switches comes along in a rugged metal enclosure

with an auto-ranging power supply for operation with standard AC power worldwide.

2.2.1 Magnum 4K220 Switch chassis

Magnum 4K220 Switches come with a 40-switched RJ-45 ports enclosed in a

rack-mountable chassis and ready to install in any of the ETSI (19”) and TELCO (23”)

environments by the available brackets.

The LED status indicators and the manual switches are located on the front

panel of Magnum 4K220 Switches. There are Full-duplex/Collision (FDX/COL),

Link/Activity (LINK/ACT) and (100/10) LED indicators for each 10Mbps and

100Mbps domain, for visual indication of the operating status of each domain. The IEC

standard AC power connector (and a manual ON - OFF power switch) is located at the

Magnum 4K220 Switches Installation and User Guide (10/04)

www GarrettCom com

rear. Fan-driven cooling air flows left to right.

Fig. 2.2.1: Magnum 4K220CR “Reverse” model, front LEDs and

connections in Rear , AC power supply version

2.2.2: Magnum 4K220CR “Reverse” model, front LEDs and

connections in Rear , -48VDC optional power supply version

The Magnum 4K220CR-48VDC has the LEDs on the front panel, and all

the connecting ports and power feeds are in the back. This is convenient for rack-

mounting where cabling is accessed from the rear of the rack while the operating status

LEDs are monitored from the front. Typically such arrangements are found in telco rack

installations.

The Magnum 4K220CR-48VDC is a dual-speed 10/100Mbps switch. The

switching capability allow the Magnum 4K220CR to support multiple workgroups

smoothly, each with its own switched 100Mbps or 10Mbps domain.

The 4K220CR may be equipped with an optional internal -48VDC power

supply (See Appendix A). There is an additional option of a dual-source -48V input

(See Appendix B). The DC power feed options and the high quality and versatility

make the Magnum 4K220CR a good high-availability choice for network traffic center

= X

UPLINK

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39

115-230V~ 50/60 Hz

Power

Col/FDX Col/FDX

Magnum 4K220R-Series

Ethernet 10/100 Switch

100M

Col/FDX

Link/Act

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

(-) GND (+)

48V DC = X

UPLINK

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39

Power

Col/FDX Col/FDX

Magnum 4K220R-Series

Ethernet 10/100 Switch

100M

Col/FDX

Link/Act

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Inhaltsverzeichnis

Andere GarrettCom Schalten Handbücher

GarrettCom

GarrettCom Hubs Bedienungsanleitung

GarrettCom

GarrettCom 500-Series Bedienungsanleitung

GarrettCom

GarrettCom Magnum 4K24F Bedienungsanleitung

GarrettCom

GarrettCom Magnum 6K32T Bedienungsanleitung

GarrettCom

GarrettCom P80C Bedienungsanleitung

GarrettCom

GarrettCom MAGNUM MAGNUM 6KM Bedienungsanleitung

GarrettCom

GarrettCom MAGNUM H80B Bedienungsanleitung

GarrettCom

GarrettCom Magnum 6K32F Bedienungsanleitung

GarrettCom

GarrettCom Magnum 4K16 Bedienungsanleitung

GarrettCom

GarrettCom Magnum Quad-Series Bedienungsanleitung

GarrettCom

GarrettCom Magnum CSG14 Bedienungsanleitung

GarrettCom

GarrettCom Magnum ST80 Stackable Bedienungsanleitung

GarrettCom

GarrettCom Magnum 8000X Bedienungsanleitung

GarrettCom

GarrettCom Magnum 6K32F Bedienungsanleitung

GarrettCom

GarrettCom PS14H-48VDC Bedienungsanleitung

GarrettCom

GarrettCom Magnum 6K32T Gebrauchsanweisung

GarrettCom

GarrettCom Magnum 6KQ Bedienungsanleitung

GarrettCom

GarrettCom magnum 6kl Bedienungsanleitung

GarrettCom

GarrettCom Hardened Ethernet Switches P62F Bedienungsanleitung

GarrettCom

GarrettCom Magnum 14E Bedienungsanleitung

GarrettCom

GarrettCom Magnum 6K25 Bedienungsanleitung

GarrettCom

GarrettCom Magnum CS14 Series Bedienungsanleitung

GarrettCom

GarrettCom Magnum S14 Bedienungsanleitung

GarrettCom

GarrettCom Quad Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung