Geemarc AMPLICALL 100 Bedienungsanleitung

Multi-Alert Receiver with doorbell

Récepteur d’alerte sans fil avec sonnette

Multi-Alarm-Empfänger mit Türklingel

English P2

Français P9

Deutsch P17

!!! Please refer to our website: www.geemarc.com for an up to date user guide, as there may

be important updates and changes you need to be aware of !!!

PACKAGE CONTENTS

The package contains the following items:

1 user’s manual

1 AMPLICALLTM100 (AC100) base

1 AMPLICALLTM101 (AC101) remote

1 AC power adapter

5 screws and 5 fixing holes

1 wall bracket and 1 lanyard bracket.

DESCRIPTION

Reset button

Function switch

* Chime

* Chime and Light

* Light

Vibration on indicator

Vibration ON/OFF

9V ready

Vibration out

Output delay

Relay output control

Power adapter jack

Wire clip

Flash light

Zone icon from 1 to 6

Speaker

Volume control

Learn melody

Melody selector

Battery compartment

Battery cover

INSTALLATION

Battery installation in the base

(needed in case of a power

failure)

1. Open the battery cover by

pulling it.

2. Insert three 1.5V LR14 alkaline

batteries (not provided) (C) into

the battery compartment, while

ascertaining that the polarity is

(+/-) .

3. Close the battery cover.

4. Plug the power cable into the

power adapter jack found on

the side of the AMPLICALL100

(A). Plug the adaptor into the

mains on the wall (B).

9V ready indicator: This indicator

will light up, when the 9V adaptor

is connected correctly.

LOW BATTERY INDICATOR ON THE AC100

If a zone icon LED light is blinking, it indicates that the battery power is too low for the

corresponding device (AC101, AC110 or AC140. You must replace the battery as

soon as possible.

If your AMPLICALL100 flash light blinks every 15 seconds, this indicates that the

AMPLICALL100 battery power is too low or that the batteries are not installed.

Please, disconnect the power and install new batteries.

AMPLICALLTM101

Put the bell press to the wall bracket or lanyard bracket

1. Place the mounting bracket that you have chosen (Fig 1 for the wall bracket or

Fig 2 for the lanyard bracket) to 90 degrees.

2. Rotate the mounting bracket until the part locks.

DC9V,1A

Fig1 or Fig2

Batteryinstallationintheremote

1. Use your finger to unlock the

lock lever (fig ).

2. Rotate the mounting bracket to

90 degrees (fig ).

3. Remove the mounting bracket

from the unit (fig ).

4. Rotate the battery cover using

a coin (fig ).

5. Insert a CR2032 battery into

the battery compartment with

the polarity + on top. (fig ).

6. Close the battery cover using

a coin. (fig ).

7. Replace the mounting bracket

to 90 degrees. (fig ).

8. Rotate the mounting bracket until the part locks.

WALL MOUNTING

You can install your AMPLICALLTM100 onto a wall.

Please, follow the recommendations below.

1. Place the wall

support against the

wall and mark the

three holes of the

wall support on the

wall.

2. Drill two holes

horizontally, 36 mm

apart, and drill the

third hole between

the 2 holes at 13.5

mm above the

virtual line between

the first two holes.

3. Insert three wall

plugs fixing into the

three holes.

4. Screw three screws into the plugs, hang the base on the support and slide it to the

left to lock it.

Pairing a new device AMPLICALLTM101/110 or 140 with

AMPLICALLTM100

Note : When you receive your AMPLICALLTM100

with the AMPLICALLTM101 doorbell, the devices

are paired already. So, you do not need to follow

the following steps.

To pair a new device, please follow these steps:

Step 1: Enter pairing mode for the AC100 Press & hold the LEARNING button (●)

for 3 seconds. The LED in zone icon #1 will flash.

Step 2: Press the LEARNING button (●) again to move to the zone icon you wish to

pair with.

Press the melody selector ( ) button to scroll through the melodies. Once you

hear a melody you like, do not press any button during the melody.

Step 3: Once the zone icon and melody are selected, press one time on device (AC101,

AC110 or AC140) button to pair. If successful, the AC100 will generate two

short tones.

Press the LEARNING button (●) to exit the pairing mode; the system is now

ready to use

To stop the Chime while the AMPLICALLTM100 is alerting, press the reset button

located at the top back.

Deleting one device from the AMPLICALLTM100 memory

- First, press and hold the 'Learning' button for 3 seconds to enter pairing mode.

- Press the 'Learning’ button to select the zone you want to delete.

- Press and hold both the ' Learning' and the ' Melody' buttons for 3 seconds.

- The AMPLICALLTM100 will generate a tone to indicate the device for this zone has

been deleted.

- Press the Reset button at the back to exit.

Charging the melody/tone of the desired zone icon

- First, press and hold the 'Learning' button for 3 seconds to enter pairing mode.

- Press the 'Learning’ button to select the zone icon you want to change.

- Press the 'Melody' button to select the new melody/tone and then press learning

button. You will hear a tone to indicate the modification was successful.

- Press the Reset button at the back to exit.

Zone selector

Learning button

Melody selector

Replacing the zone icon plate

After pairing your device (AC101, AC110 or AC140), do not forget to change the zone

icon image that is provided with the device (AC101, AC110 or AC140).

1. Open the battery cover (fig ).

2. Slide down and lift up the transparent flasher cover (fig ).

3. Push the bottom of the zone icon image to remove it (fig ).

4. Put the new icon plate delivered with your device (AC101, AC110 or AC140) into

the slot (fig ).

5. Press the top of the icon plate to fix it (fig ).

6. Install the transparent cover (first, insert the top and then clip the bottom of the

transparent plastic; you should hear a beep) (fig ).

7. Install the battery cover.

Shake (Optional)

Note: If you want to use the Shaker option, it is recommended to connect power adaptor

(9V 1A, AC/DC) in addition to the batteries. This shaker will vibrate every time the

base receives an alert.

Pad On/Off : Slide the PAD switch to turn ON or OFF the vibration function.

Pad On Indicator : If the Shaker On/Off switch is in the On position, the LED indicator

will light up to indicate vibration function is activated.

Pad OUT : Plug the Shaker into this jack.

Note: ●The shaker can be used for all zone icons.

●The shaker can be bought separately (CLA2).

WIRING AND SETTING the door opening function

You have the possibility to command your door opening

automatically, if the

captor of zone icon 5 or 6 receives a

trigger signal. Check the user guide of your

gate trigger to connect your door opening device to the AMPLICALLTM100.

DC9V,

jack

9V Ready Indicator

Pad On Indicator

Pad On/Off Switch

Shaker plug

Using a small

screwdriver, press

the lever and insert

the wire inside the

hole. Then release

the lever to hold the

wire.

Normal Open

(NO)

Normal Close

(NC) 9V out

Relay output control switch

Slide the switch on/off button to the 'On' position: the relay will activate when zone

icon 5 or 6 receives a trigger signal.

Slide the switch to the 'Off' position: the relay will not activate when zone icon 5 or

6 receives a trigger signal.

Duration of the Relay output control

Slide the switch to the '2' position, the relay will activate 2 seconds when zone icon 5

or 6 receives a trigger signal.

Slide the switch to the '5' position, the relay will activate 5 seconds when zone icon 5

or 6 receives a trigger signal.

GUARANTEE

From the moment your Geemarc AMPLICALLTM100 is purchased, Geemarc guarantee

is for the period of two years. During this time, all repairs or replacements (at our

discretion) are free of charge. Should you experience a problem then contact our help

line or visit our website at www.geemarc.com. The guarantee does not cover

accidents, negligence or breakages to any parts. The product must not be tampered

with or taken apart by anyone who is not an authorized Geemarc representative. The

Geemarc guarantee in no way limits your legal rights.

IMPORTANT : YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE

RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.

Please note : The guarantee applies to the United Kingdom only.

DECLARATIONS:

UKCA Directives

Geemarc Telecom SA hereby declares that this AMPLICALL100 is in compliance with

the essential requirements and other relevant provisions of the Radio Equipment

Directive 2014/53/UE.

The UKCA declaration of conformity may be consulted at www.geemarc.com

RF power : < 250mW

Recycling Directives

The WEEE (Waste Electrical and Electronic Equipment) has been put in place for the

products at the end of their useful life are recycled in the best way.

When this product is finished with, please do not put it in your domestic waste bin.

Please use one of the following disposal options:

- Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the

product in an appropriate WEEE skip.

- Or, hand the old product to the retailer. If you purchase a new one, they should

accept it.

Thus if you respect these instructions you ensure human health and environmental

protection.

For product support and help visit our website at www.geemarc.com

E-mail : [email protected] telephone 01707 387602

lines are open 09h00 to 16h00 Mon to Fri

2 Rue Galilée, Parc de l’Etoile, 59791 Grande-Synthe Cedex, France

This product is made in China To Geemarc Telecom

!!! Veuillez consulter notre site Web: www.geemarc.com car il peut y avoir des mises à jour

importantes et changement dont vous devez être conscient !!!

Contenu de la boite

La boite contient les éléments suivants:

1 guide d’utilisation

1 base AMPLICALLTM100 (AC100)

1 télécommande AMPLICALLTM101

1 adaptateur secteur

5 vis et 5 chevilles

1 support mural et 1 cordon tour de cou

pour AC101.

DESCRIPTION

Bouton de réinitialisation

Commutateur de fonctions

* Carillon

* Flash et carillon

* Flash

Voyant Vibreur activé

Vibreur Activé / Désactivé

9V prêt

Connecteur du vibreur

Délai d’ouverture relais

Commande de sortie de relais

Connecteur Adapatateur 9V DC/1A

Clip de fil

Flash

Icône de zones 1 à 6

Haut-parleur

Réglage du volume

Bouton de programmation de mélodie

Bouton de sélection de la mélodie de

sonnerie

Compartiment de piles LR14*3

Couvercle du compartiment des piles

INSTALLATION

Installation des piles dans la

base (nécessaire en cas de

coupure de courant)

1. Ouvrez le couvercle du

compartiment des piles en le

tirant vers l’avant.

2. Insérez 3 piles alcalines LR14

de 1,5 V (non fournies) (C) dans

le compartiment des piles, tout

en vérifiant que la polarité est

correcte (+/-) .

3. Fermez le couvercle du

compartiment des piles.

4. Branchez le câble d'alimentation

dans la prise de l'adaptateur

électrique qui se trouve sur le

côté de AMPLICALLTM100 (A).

Branchez l'adaptateur dans la

prise secteur murale (B).

Voyant « 9V ready »: ce témoin

s'allume lorsque l'adaptateur 9V

est correctement branché.

INDICATEUR DE BATTERIE FAIBLE SUR L'AC100

Si le voyant LED d'une icône de zone clignote, cela indique que la puissance de la

batterie est trop faible pour le dispositif correspondant (AC101, AC110 ou AC140).

Vous devez remplacer les piles le plus rapidement possible.

Si votre voyant AMPLICALLTM100 clignote toutes les 15 secondes, cela indique que

la puissance des piles de l' AMPLICALLTM100 est trop faible ou que les piles ne sont

pas installées. Veuillez couper le courant et installer de nouvelles piles.

AMPLICALLTM101

Placez la plaque de sonnerie sur le support mural ou sur le cordon tour de cou

1. Placez le support de montage que vous avez choisi (fig.1 pour le support mural ou

fig.2 pour le cordon tour de cou) à 90 degrés.

2. Faites tourner le support de montage jusqu'à ce que la pièce se verrouille.

CC9V,1A

Fig1 ou Fig2

Inhaltsverzeichnis

Sprachen:

Andere Geemarc Empfänger Handbücher

Geemarc

Geemarc AMPLICALL 150 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung