Generac Power Systems 2100PSI 1974-0 Bedienungsanleitung

Owner’s Manual / Manual del Propietario

Questions? Help is just a moment away!

Preguntas? La ayuda es justa un momento lejos!

Call: Generac Pressure Washer Helpline

Llame: Línea Directa del Lavador a Presión de Generac - 1-800-270-1408 M-F 8-5 CT

Web: www.generac-portables.com

Model No. 1974-0 (2100 PSI Pressure Washer) Manual No. 193729GS Revision 0 (09/17/2003)

2100PSI

Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products.

Generac Portable Products es una marca registrada licenciada de Briggs & Stratton Power Products.

Generac Portable Products 2100 PSI Pressure Washer

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Last Page

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your pressure washer. Know its

applications, its limitations and any hazards

involved.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or serious

injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface Fall

Kickback

Flying Objects

Fluid Injection

Generac Portable Products 2100 PSI Pressure Washer

• Keep water spray away from electric wiring or fatal electric

shock may result.

Spray contact with electrical wiring can result in

electrocution.

WARNING

• Operate pressure washer ONLY outdoors.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful vapors.

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

• Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

• Operate this unit on a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

Use of pressure washer can create puddles and

slippery surfaces.

High pressure spray could cause you to fall if

you are too close to the cleaning surface.

WARNING

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing gas cap.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel

to spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• NEVER aim spray gun at people, animals or plants.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury and

possible amputation.

WARNING

Generac Portable Products 2100 PSI Pressure Washer

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

Excessively high or low operating speeds increase risk

of injury and damage to pressure washer.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect spark plug wire from spark plug and place wire

where it cannot contact spark plug.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT point spray gun at glass when in jet spray mode.

• NEVER aim spray gun at plants.

High pressure spray may damage fragile items including

glass.

CAUTION

• DO NOT wear loose clothing, jewelry or anything that may

be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

WARNING

• Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

High pressure spray can cause paint chips or

other particles to become airborne.

WARNING

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

• If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by–pass any safety device on this machine.

• Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on high pressure hose. Use

handle provided on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washer.

• This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used

with parts that DO NOT comply with minimum specifications,

user assumes all risks and liabilities.

Improper treatment of pressure washer can damage it

and shorten its life.

CAUTION

• DO NOT touch hot surfaces.

• Stay clear of exhaust gases.

• Allow equipment to cool before touching.

Running engines produce heat and hot exhaust

gases.Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Fire or severe burns can occur.

WARNING

Generac Portable Products 2100 PSI Pressure Washer

KNOWYOUR PRESSURE WASHER

Read this owner’s manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

Air Cleaner — Dry type filter element limits the amount

of dirt and dust that gets in the engine.

Automatic Cool Down System — Cycles water

through pump when water reaches 125°-155°F. Warm

water will discharge from pump onto ground.This

system prevents internal pump damage.

Chemical Injection Siphon/Filter — Use to siphon

detergent or other pressure washer chemicals into the low

pressure stream.

FuelTank — Fill tank with regular unleaded fuel.

High Pressure Hose — Connect one end to water

pump and the other end to spray gun.

High Pressure Outlet — Connection for high pressure

hose.

Data Tag (not shown, near rear of base plate) –

Provides model and serial number of pressure washer.

Please have these readily available if calling for assistance.

Primer Bulb — Prepares a cold engine for starting.

Pump — Develops high water pressure.

Recoil Starter — Used for starting the engine manually.

Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes safety latch.

Water Inlet — Connection for garden hose.

Air Cleaner

Primer Bulb

Fuel Tank

Pump equipped with

Automatic Cool Down

System

Recoil Starter

High Pressure Outlet

& Water Inlet

Chemical Injection

Siphon/Filter

Spray Gun

High Pressure Hose

Generac Portable Products 2100 PSI Pressure Washer

ASSEMBLY

IMPORTANT: Read entire owner’s manual before you

attempt to assemble or operate your new pressure washer.

Remove Pressure Washer From

Carton

1. Remove the parts bag, accessories, and inserts included

with pressure washer.

2. Slice two corners at the end of carton from top to

bottom so the panel can be folded down flat.

3. Remove pressure washer from carton.

Carton Contents

Items in the carton include:

• Main Unit

• Handle

• High Pressure Hose

• Spray Gun

• Nozzle Extension

• Safety Goggles

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Engine Manual

• Owner’s Registration Card

• Handle Attachment Hardware

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or damaged, call the

pressure washer helpline at 1-800-270-1408. If calling for

assistance, please have the model, revision, and serial

number from the data tag available.

To prepare your pressure washer for operation, you

will need to perform these tasks:

1. Fill out and send in registration card.

2. Attach handle to main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

Attach Handle

1. Place handle assembly onto handle supports connected

to main unit. Make sure holes in handle align with

holes on handle supports (Figure 1).

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts through holes from outside of

unit and attach a plastic knob from inside of unit

(Figure 2).Tighten by hand.

3. Insert one “L” hooks through hole just under billboard

on left side of handle (viewing from rear of unit). Hold

hook in place with pliers and attach locknut with

7/16” wrench (Figure 3).

4. Insert other “L” hook through hole just above

billboard on right side of handle (viewing from rear of

unit). Hold hook in place with pliers and attach locknut

with 7/16” wrench (Figure 3).

Align Holes

Handle

Supports

Figure 1 — Attach Handle to Base

Figure 2 — Secure Handle

Hose Hook

Spray Gun

Hook

Figure 3 — Attach “L” Hooks to Handle

Generac Portable Products 2100 PSI Pressure Washer

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

• Refer to engine owner’s manual and follow oil and fuel

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine owner’s manual for recommendations.

Connect Hose and Water Supply to

Pump

IMPORTANT: To avoid pump damage, you must assemble

the nozzle extension to the spray gun and attach all hoses

before you start the engine.

1. Uncoil high pressure hose and attach one end of hose

to base of spray gun (Figure 4).Tighten by hand.

NOTE: Remove and discard all pump shipping caps before

attaching hoses.

2. Attach other end of high pressure hose to high

pressure outlet on pump (Figure 5).Tighten by hand.

3. Before connecting garden hose to water inlet, inspect

inlet screen (Figure 6). Clean screen if it contains

debris or have it replaced if damaged. Refer to the

section “O-Ring Maintenance” if inlet screen is

damaged. DO NOT RUN PRESSURE WASHER IF

INLET SCREEN IS DAMAGED.

4. Run water through your garden hose for 30 seconds

to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

5. Connect the garden hose (not to exceed 50 feet in

length) to the water inlet.Tighten by hand (Figure 6).

6. Turn ON the water and squeeze the trigger on the

gun to purge the pump system of air and impurities.

Connect high pressure

hose here

Figure 4 — Connect High Pressure Hose to Spray Gun

Figure 5 — Connect High Pressure Hose to Pump

CAUTION

• Refer to engine manual for oil and fuel fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

There MUST be at least ten feet of unrestricted garden

hose between the pressure washer inlet and any flow

shut off device, such as a ‘Y’ shut-off connector or other

convenience-type water shut-off valve.

Inspect inlet

screen, DO NOT

use if damaged;

clean if dirty.

Figure 6 — Connect the Garden Hose to Water Inlet

• Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate eye protection.

High pressure spray can cause paint chips or

other particles to become airborne.

WARNING

Generac Portable Products 2100 PSI Pressure Washer

CHECKLIST BEFORE

STARTING ENGINE

Review the unit’s assembly to ensure you have performed

all of the following.

1. Make sure handle is in place and secure.

2. Check that oil has been added to proper level in the

engine crankcase.

3. Add proper gasoline to fuel tank.

4. Check for properly tightened hose connections.

5. Check to make sure there are no kinks, cuts, or

damage to high pressure hose.

6. Provide a proper water supply at an adequate flow.

7. Be sure to read “Safety Rules” and “How To UseYour

Pressure Washer” before using pressure washer.

HOW TO USEYOUR

PRESSURE WASHER

If you have any problems operating your pressure washer,

please call the pressure washer helpline at

1-800-270-1408.

How to StartYour Pressure Washer

To start your pressure washer for the first time, follow

these instructions step-by-step.This starting information

also applies if you have let the pressure washer sit idle for

at least a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

3.0 gallons per minute and no less than 20 PSI at

pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See “Preparing Pressure Washer

for Use” for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

5. Attach adjustable nozzle extension to spray gun

(Figure 7).Tighten by hand.

6. Position nozzle in low pressure mode (see “How to

Use the Adjustable Nozzle”) and squeeze trigger on

spray gun to relieve air pressure caused by turning ON

water.Water will flow out of spray gun in a thin

stream. Continue to hold trigger until there is a steady

stream of water and no air remains in system.This will

make it easier to pull start engine. Release trigger.

7. Engage safety latch to spray gun trigger (Figure 8).

8. Start engine according to instructions given in engine

owner’s manual.

NOTE: If the recoil starter is hard to pull, squeeze the

spray gun trigger to relieve internal pump pressure.

NOTE: Always keep the throttle lever in the “Fast”

position when operating the pressure washer.

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

DO NOT run the pump without the water supply

connected and turned on.

Figure 7 — Connect Nozzle Extension to Spray Gun

Safety Latch

Figure 8 — Spray Gun with Safety Latch Engaged

CAUTION

• Squeeze trigger on spray gun each time recoil starter is

pulled and engine fails to start.

Avoid injury from kickback.

Generac Portable Products 2100 PSI Pressure Washer

How to StopYour Pressure Washer

1. Let engine idle for two minutes.

2. Turn engine off according to instructions given in

engine owner’s manual.

3. Squeeze trigger on the spray gun to relieve

pressure in the hose.

NOTE: A small amount of water will squirt out when you

release the pressure.

How to Use the Adjustable Nozzle

You should now know how to START and STOP your

pressure washer.The information in this section will tell

you how to adjust the spray pattern and to apply detergent

or other cleaning chemicals.

1. Slide nozzle forward when you wish to adjust spray to

low pressure mode (Figure 9). Slide nozzle backward

to achieve high pressure.

2. Point nozzle down towards a firm surface and press

trigger to test pattern (Figure 10).

3. Twisting nozzle adjusts spray pattern from a narrow

pattern to a fan pattern (Figure 11).

4. For most effective cleaning, keep spray nozzle from

8 to 24 inches away from cleaning surface.

5. If you get spray nozzle too close, especially using high

pressure mode, you may damage surface being cleaned.

6. DO NOT get closer than 6 inches when cleaning tires.

• NEVER adjust spray pattern when spraying.

• NEVER put hands in front of nozzle to adjust spray pattern.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

Slide nozzle backward

for High Pressure

Mode

Slide nozzle forward for low

pressure mode and

detergent application

Figure 9 — Adjusting Nozzle for Pressure

Figure 10 — Testing the Spray Pattern

Figure 11 — Adjusting the Nozzle for Spray Pattern

Rotate nozzle

counterclockwise for fan

spray pattern

Rotate nozzle clockwise

for narrow spray pattern

Generac Portable Products 2100 PSI Pressure Washer

Applying Detergent with the

Adjustable Nozzle

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could damage

the pump.

To apply detergent, follow these steps:

1. Review use of adjustable nozzles.

2. Prepare detergent solution as required by job.

3. Place filter end of chemical injection hose into

detergent container.

4. Slide adjustable nozzle forward to low pressure mode.

Detergent cannot be applied with nozzle in high

pressure position.

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Start engine.

6. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

7. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry

on (prevents streaking).

IMPORTANT: You must flush the chemical injection

system after each use by placing the filter into a bucket of

clean water, then run the pressure washer in low pressure

for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Slide the nozzle backward to high pressure, press the

trigger and wait for the detergent to clear.

NOTE: You can also stop detergent from flowing by simply

removing chemical injection hose from bottle.

2. Keep the spray gun a safe distance from the area you

plan to spray.

3. Apply a high pressure spray to a small area, then check

the surface for damage. If no damage is found, it is okay

to continue cleaning.

4. Start at the top of the area to be rinsed, working

down with same overlapping strokes as you used for

washing and applying detergent.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures

above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

CAUTION

• Starting the engine without all the hoses connected and

without the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

You must attach all hoses before you start the engine.

CAUTION

• When inserting the filter into a detergent solution bottle,

route the tube so as to keep it from inadvertently contacting

the hot muffler.

Keep the chemical injection tube from coming in contact

with the hot muffler.

• Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

• Operate this unit on a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

High pressure spray could cause you to fall if

you are too close to the cleaning surface.

WARNING

Inhaltsverzeichnis

Sprachen:

Andere Generac Power Systems Hochdruckreiniger Handbücher

Generac Power Systems

Generac Power Systems 1455-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1455-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1293-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6228-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1195-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems The Reliable Ones Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1300PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 5993-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems 3000PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1700PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems Pro 6712 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1300PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1173-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2100PSI 1536-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1292-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1067-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1044-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1014-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2000PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6000CP Bedienungsanleitung

Generac Power Systems

Generac Power Systems 4040 PRO GAS PW 49ST Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung

Hotsy

Hotsy 5645 Bedienungsanleitung