GeoMax ZTS600 Bedienungsanleitung

GeoMax ZTS600

User Manual

Version 1.2

ZTS600 | 2Introduction

Introduction

Purchase Congratulations on the purchase of a ZTS600 instrument.

This manual contains important safety directions as well as instructions for

setting up and operating the product. Refer to "13 Safety Directions" for

further information.

Read carefully through the User Manual before you switch on the product.

Product identifi-

cation The model and serial number of your product are indicated on the type plate.

Enter the model and serial number in your manual and always refer to this

information when you need to contact your agency or GeoMax authorised

service workshop.

Model: ______________________________________________

Serial No.: ______________________________________________

Introduction ZTS600 | 3

Symbols The symbols used in this manual have the following meanings:

Trademarks • Windows is a registered trademark of Microsoft Corporation.

All other trademarks are the property of their respective owners.

Type Description

Danger Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

Warning Indicates a potentially hazardous situation or an unintended

use which, if not avoided, could result in death or serious

injury.

Caution Indicates a potentially hazardous situation or an unintended

use which, if not avoided, may result in minor or moderate

injury and/or appreciable material, financial and environ-

mental damage.

Important paragraphs which must be adhered to in practice

as they enable the product to be used in a technically correct

and efficient manner.

ZTS600 | 4Introduction

Validity of this

manual Description

General This manual applies to ZTS600 instruments.

Tele-

scope •Measuring with IR mode: When measuring distances to a

reflector with Electronic Distance Measurement (EDM) mode

"IR", the telescope uses a wide visible red laser beam, which

emerges coaxially from the telescope's objective.

•Measuring with RL modes: Instruments that are equipped

with a reflectorless EDM additionally offer the EDM mode

"RL". When meauring distances with this EDM mode, the

telescope uses a narrow visible red laser beam, which

emerges coaxially from the telescope's objective.

Table of Contents ZTS600 | 5

Table of Contents

In this manual Chapter Page

1 Description of the System 11

1.1 System Components 11

1.2 Container Contents 13

1.3 Instrument Components 14

2UserInterface 15

2.1 Keyboard 15

2.2 Status Icons 17

2.3 Softkeys 18

2.4 Operating Principles 20

2.5 Pointsearch 22

3Operation 24

3.1 Instrument Setup 24

3.2 Working with the Battery 29

3.3 Data Storage 31

3.4 Main Menu 32

3.5 Measure Application 33

3.6 Distance Measurements - Guidelines for Correct Results 34

ZTS600 | 6Table of Contents

4 Configuration 37

4.1 Main Configuration 37

4.2 Communication Setup 45

4.3 EDM Configuration 47

4.4 Start Sequence 51

4.5 System Information 52

5Calibration 54

6 Functions 55

6.1 Overview 55

6.2 Distance Offset 57

6.2.1 Overview 57

6.3 Z-Coordinate 59

6.4 2 Dist. Offset 61

6.5 Control Distance 63

6.6 Continuous-EDM Mode 65

7Coding 66

7.1 Standard Coding 66

7.2 Rapid Coding 68

Table of Contents ZTS600 | 7

8 Applications - Getting Started 70

8.1 Starting an Application 70

8.2 Setting the Job 71

8.3 Setting the Station 73

8.4 Setting the Orientation 74

8.4.1 Overview 74

8.4.2 Manual Orientation 75

8.4.3 Orientation with Coordinates 76

9Applications 80

9.1 Common Fields 80

9.2 Topography 81

9.3 Set Out 82

9.4 Resection 87

9.4.1 Starting Resection 87

9.4.2 Measuring Information 89

9.4.3 Computation Procedure 90

9.4.4 Resection Results 91

9.5 Point Projection - Line 94

9.5.1 Overview 94

9.5.2 Defining the Base Line 94

9.5.3 Defining the Reference Line 96

9.5.4 Subapplication Measure Line & Offset 98

9.5.5 Subapplication Setout 100

9.6 Point Projection - Arc 104

ZTS600 | 8Table of Contents

9.6.1 Overview 104

9.6.2 Defining the Reference Arc 105

9.6.3 Subapplication Measure Line & Offset 107

9.6.4 Subapplication Setout 108

9.7 Missing Line (MLM) 113

9.8 Area 116

9.9 Remote Elevation (REM) 120

9.10 Construction 122

9.10.1 Starting Construction 122

9.10.2 Layout 123

9.10.3 As Built Check 125

9.11 Calculations 127

9.11.1 Starting Calculations 127

9.11.2 Inverse and Traverse 128

9.11.3 Intersections 129

9.11.4 Offsets 132

9.11.5 Extension 133

9.12 Road Alignment 134

10 Data Management 140

10.1 Data Management 140

10.2 Data Transfer 142

10.3 Working with GeoMax Office Software 144

Table of Contents ZTS600 | 9

11 Check & Calibrate 145

11.1 Overview 145

11.2 Preparation 146

11.3 Calibrating Line-of-Sight and Vertical Index Error 147

11.4 Calibrating the Circular Level of the Instrument and Tribrach 151

11.5 Inspecting the Laser Plummet of the Instrument 152

11.6 Servicing the Tripod 154

12 Care and Transport 156

12.1 Transport 156

12.2 Storage 157

12.3 Cleaning and Drying 158

13 Safety Directions 160

13.1 General 160

13.2 Intended Use 160

13.3 Limits of Use 162

13.4 Responsibilities 162

13.5 Hazards of Use 163

13.6 Laser Classification 168

13.6.1 General 168

13.6.2 Distancer, Measurements with Reflectors 169

13.6.3 Distancer, Measurements without Reflectors 171

13.6.4 Laser Plummet 174

13.7 Electromagnetic Compatibility EMC 177

ZTS600 | 10Table of Contents

13.8 FCC Statement, Applicable in U.S. 179

14 Technical Data 181

14.1 Angle Measurement 181

14.2 Distance Measurement with Reflectors 182

14.3 Distance Measurement without Reflectors (RL mode) 184

14.4 RL to Prism 185

14.5 Conformity to National Regulations 187

14.6 General Technical Data of the Instrument 188

14.7 Scale Correction 191

14.8 Reduction Formulas 195

15 International Limited Warranty, Software License Agreement 197

16 Glossary 199

Appendix A Menu Tree 203

Index 205

Inhaltsverzeichnis

Andere GeoMax Messgerät Handbücher

GeoMax

GeoMax Zoom70 Bedienungsanleitung

GeoMax

GeoMax Zoom75 Bedienungsanleitung

GeoMax

GeoMax Zoom80 Series Bedienungsanleitung

GeoMax

GeoMax ZIPP10 pro series Bedienungsanleitung

GeoMax

GeoMax Zoom40 Series Bedienungsanleitung

GeoMax

GeoMax Zoom70 Bedienungsanleitung

GeoMax

GeoMax ZONE60 HG Bedienungsanleitung

GeoMax

GeoMax Zoom3D Bedienungsanleitung

GeoMax

GeoMax Zoom80 Series Bedienungsanleitung

GeoMax

GeoMax Zoom90 Bedienungsanleitung

GeoMax

GeoMax Zoom 20 Pro Series Bedienungsanleitung

GeoMax

GeoMax Zoom 20 series Bedienungsanleitung

GeoMax

GeoMax Zipp02 Bedienungsanleitung

GeoMax

GeoMax Zipp20 series Bedienungsanleitung

GeoMax

GeoMax Zoom90 Bedienungsanleitung

GeoMax

GeoMax EZDig Bedienungsanleitung

GeoMax

GeoMax Zoom40 Series Bedienungsanleitung

GeoMax

GeoMax Zoom90 Bedienungsanleitung

GeoMax

GeoMax ZIPP10 pro series Bedienungsanleitung

GeoMax

GeoMax ZONE20 H Bedienungsanleitung

GeoMax

GeoMax Zenith60 Series Bedienungsanleitung

GeoMax

GeoMax Zeta125 Bedienungsanleitung

GeoMax

GeoMax ZIPP10 pro series Bedienungsanleitung

GeoMax

GeoMax Zoom10 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung