Glomex ZigBoat ZB205 Bedienungsanleitung

eng

Green dot: The sensor is working properly

Red dot: The sensor is not able to reach the

Gateway:

• Please check the battery status;

• Please check you have insert the correct serial

number

• In case of a weak or a bad signal, change

the location of the ZigBoat™ Porthole/Door

Sensor

“CLOSED”: The door or porthole is closed

“OPEN”: The door or porthole is open

Resetting

Resetting is needed if you want to connect your

ZigBoat™ Porthole/Door Sensor to another

gateway or if you need to perform a factory

reset to eliminate abnormal behavior.

The reset button is marked with the small ring

on the front of the sensor.

STEPS FOR RESETTING

1. Open the casing of the device by pushing

the fastening on top of the device to remove

the front panel from the back cover.

Mounting

• Clean the surface before mounting.

• The ZigBoat™ Porthole/Door Sensor (a)

should be mounted to the frame using the

double stick tape, already applied on the

back of the sensor and magnet. Press rmly

to secure sensor.

Testing

You can test if the positioning of the sensor

and magnet are correct by checking whether

the green light on the ZigBoat™ Porthole/Door

Sensor is ashing when you open or close the

porthole/door.

Placement

• Place the sensor indoors at a temperature

between 0-50°C.

• The magnet has to be placed on that side

of the sensor which is marked with a small

triangle.

• The magnet and sensor also have to be

aligned/centered thickness-wise on as

similar level as possible.

• In case of a weak or a bad signal, change

the location of the ZigBoat™ Porthole/Door

Sensor .

• When removing cover for battery change,

electrostatic discharge can harm electronic

components inside.

• Always mount indoors.

• Do not place the sensor close to magnetic

or electromagnetic elds. This device

includes a magnet. The magnet creates

a magnetic eld that may cause damage

to computer hard drives, magnetic cards,

data storage devices, hearing aids and

speakers e.g. Therefore, we strongly advise

you to never position the magnet close to

electronic devices.

Adding the sensor to the Gateway

NOTE: Make sure Gateway is turned on

and congurated, for more details see the

Gateway owner’s manual.

1. Open the ZigBoat™ App, select the Gateway

in the ZB Gateways menu, wait a few

seconds, then select the menu button on

the top right (g. 1). Select “Device list” (g.

2). Add the sensor by entering the serial

number which is on the sensor’s label (g.

3). To locate the serial number of the sensor,

remove the front cover by pressing the tab

on top.

Product description

The ZigBoat™ Porthole/Door Sensor detects

and reports opening and closing of doors

and portholes. Easily installed on any door or

portholes, the sensor triggers a signal when

parted. This lets you know when a room is

entered, if a porthole or a door has been left

open, etc.

Porthole/Door Sensor

Version 1.0

OWNER’S MANUAL

Precautions

• The magnet (b) should be mounted on the

door or porthole no further than 5mm away

from the arrow on the sensor.

• There are many ways to mount the sensor

and magnet, as portholes and doors vary

greatly. The most important consideration is

for the magnet to be placed as near to the

point on the sensor indicated by the grey

arrow.

• The sensor and magnet may be placed on

separate three dimensional planes, though

code: ZB205

SEE PAGE 2 FOR PLACEMENT ILLUSTRATIONS

Fig. 1Fig. 2

Fig. 3

3. Insert the enclosed batteries (2xAAA) into the

device, respecting the polarities.

4. Close the casing.

5. The ZigBoat™ Porthole/Door Sensor

will now start searching for the ZigBoat™

network to join.

6. While the ZigBoat™ Porthole/Door Sensor is

searching for the ZigBoat™ network to join,

the red LED is ashing.

7. When the red LED stops ashing, the

ZigBoat™ Porthole/Door Sensor has

successfully joined the ZigBoat™ network.

To check the correct conguration, select the

overview tab of the ZigBoat™ App. (g. 5)

this does aect the maximum distance

allowed. The magnet may also be placed

either facing the side of the sensor or sitting

parallel to it.

2. You can change the devices name by

selecting “Name” (g. 4). Then, press the “Add

Device” button.

<5mm

Frame Porthole/

Door

Fig. 4

Fig. 5

Placement Examples - Doors

• Be sure to mount the sensor on the frame,

to protect the electronics from heavy

vibrations.

• The sensor and magnet should be mounted

on the side opposite from the hinge/pivot

point.

• Pay careful attention to the arrow printed on

the sensor. This should be oriented to face

the magnet. The distance between the two

should not exceed 5mm.

Placement Example - Portholes

• Be sure to mount the sensor on the frame,

to protect the electronics from heavy

vibrations.

• The sensor and magnet should be mounted

on the side opposite from the hinge/pivot

point.

• Alternatively, if the porthole slides open,

the sensor and magnet may be mounted in

many positions, however the sensor should

always be placed on the frame.

• Pay careful attention to the arrow printed on

the sensor. This should be oriented to face

the magnet. The distance between the two

should not exceed 5mm.

Glomex assumes no responsibility for any

errors, which may appear in this manual.

Furthermore, Glomex reserves the right to alter

the hardware, software, and/or specications

Distributed by Glomex Srl

via Faentina 165/G

48124 Ravenna

Italy

Other certications

• ZigBee® certied.

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive 2014/53/EU

• EMC Directive 2014/30/EU

• RoHS Directive 2011/65/EU

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular,

its compliance with the harmonized standards

and specications.

Frame

Porthole

Frame

Door

Porthole

Sensor (a)

Magnet (b)

Door

Placement Examples - Top View

• The most benecial distance between the

sensor and the magnet is 0.2-0.5 cm.

• Be aware that on magnetic surface (e.g.

metal door), the distance between the

sensor and the magnet has to be 0.1-0.3 cm.

Other information

Dispose the product and battery properly at

the end of life. This is electronic waste which

should be recycled.

Disposal

Note local regulations about information to

your insurance company regarding installed

ZigBoat™ Porthole/Door Sensors.

Modes

ACTIVATION MODE

A single green ash means that the sensor

and the magnet are moving either away from

or towards each other.

Fault nding

• If the ZigBoat™ Porthole/Door Sensor

does not work when the porthole or door

is parted, the probable cause is a faulty

battery. Replace the batteries if they are

worn out.

• If the search for the ZigBoat™ Gateway has

timed out, a short press on the button will

restart it.

Battery replacement

CAUTION: RISK OF EXPLOSION IF BATTERIES

ARE REPLACED BY AN INCORRECT

TYPE. DISPOSE OF THE BATTERIES IN

ACCORDANCE WITH INSTRUCTIONS.

CAUTION: When removing cover for battery

change - Electrostatic Discharge (ESD) can

harm electronic components inside

1. Open the casing of the device by pushing

the fastening on top of the device to remove

the front panel from the back cover.

2. Replace the batteries respecting the

polarities. The ZigBoat™ Porthole/Door

Sensor uses 2xAAA batteries.

3. Close the casing.

4. Test the ZigBoat™ Porthole/Door Sensor.

2. Remove the batteries and reinsert the

batteries

3. Press and hold down the reset button for

approximately 8-10 seconds. The button

has to be pushed within one minute after

inserting the batteries.

4. When the red light starts ashing every

second, the reset process has been

successfully implemented.

SEARCHING GATEWAY MODE

Red ashes every second for a longer peri-

od, means that the device is searching for a

gateway.

LOST CONNECTION MODE

When the red LED ashes 3 times, it means

that the device has failed to connect to a

gateway.

LOW-BATTERY MODE

Two consecutive red LED ashes every 60

seconds, means that the battery should be

replaced.

Consulta il manuale utente in italiano su:

Consultez le manuel d’utilisation en français

sur:

Siehe das deutsche Benutzerhandbuch auf:

Consulte el manual de usuario en español en:

detailed herein at any time without notice, and

Glomex does not make any commitment to

update the information contained herein. All

the trademarks listed herein are owned by their

respective owners.

Warranty

Glomex guarantees the ZigBoat™ (ZB101) and

the Porthole/Door Sensor (ZB205) against

manufacturing defects for a period of 2 years

from date of purchase.

Warranty can be in the form of repair or

replacement of the unit if manufacturing

defects have been found and are conrmed

by Glomex or one of its aliates. In order to

validate warranty, either the original sales

receipt or a copy must be provided at the time

warranty is requested.

Before returning any items for warranty,

please contact the Glomex Customer Service

department to receive a RMA which should

be completed and sent with the unit to the

following address:

GLOMEX S.r.l.

Via Faentina 165/G

48124 Ravenna (Italy)

complete with all the accessories supplied at

the time of purchase for shipment.

The serial number must neither be erased nor

made illegible, otherwise the warranty will be

voided.

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Every

second

Andere Glomex Zubehör Handbücher

Glomex

Glomex ZigBoat ZB201 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung