Gorenje KGV 200-1 Bedienungsanleitung

KGV 200 - 300

Dear customer, thank you for purchasing our product.

PLEASE READ THE INSTRUCTIONS CAREFULLY PRIOR TO THE

INSTALLATION AND FIRST USE OF THE WATER HEATER.

The water heater has been manufactured in compliance with the relevant standards. Basic

technical characteristics of the product are listed on the label attached to the protective

cover.

The installation of the water heater must be carried out by qualiﬁed staff only. All repairs and

maintenance work in the interior of the water heater as well as limestone removal or testing/

replacement of the corrosion protection anode may only be carried out by an approved

maintenance service provider.

The hot water tank is designed in a manner which allows using the following heating sources,

via heat exchanger:

− central heating hot-water system

− solar power

− heating pump.

Electric heater type R may be additionally installed on the flange 180mm, or electric heater type

SH to the connecting bushing G 6/4.

INSTALLATION

The heater should be installed in a dry room that is not subject to freezing conditions,

preferably in the vicinity of other sources of heating (e.g. boiler room).

TECHNICAL CHARACTERISTICS

KGV 200-1 KGV 300-1 KGV 300-2

A 1150 1550 1550

B560 740 740

C 380 560 560

D - - 930

E - - 360

F 1010 1410 1410

HV G 1 G 1 G 1

IM G 1 G 1 G 1

CV G 3/4 G 3/4 G 3/4

VM G 1 G 1 G 1

TV G 1 G 1 G 1

KGV 200-1 KGV 300-1 KGV 300-2

H1 300 480 480

H2 - - 300

h1 100 155 155

h2 - - 210

H1, H2 - Canal for palps

h1, h2 - Position of palps

HV - Cold water inﬂow (blue rosette)

IM - HE medium outlet (blue rosette)

CV - Circulation conduit (blue rosette)

VM - HE medium inﬂow (red rosette)

TV - Cold water outﬂow (red rosette)

Type KGV 200-1 KGV 300-1 KGV 300-2

Volume [l] 200 285 280

Rated pressure [MPa ] 0,6

Weight / Filled with water [kg] 82 / 282 112 / 397 134 / 414

Anti-corrosion protection of tank Enameled/Mg Anode

HE heated surface - lowe [m2] 0,85 1,45 1,45

HE heated surface - upper [m2] - - 0,90

HE volume - lower [l] 5,3 9,1 9,1

HE volume - upper [l] - - 5,7

insulation thickness [mm] 57

Degree of protection IP 21

HE - Heat exchanger

On the rear side of the hot water tank there are special channels (H1, H2) for mounting the

feelers for regulation of the system connection of the hot water tank to other heating sources.

Access to the channels is under the covering joint of the protective covering, approximately

in the middle of the tank height.

Insert the feeler into the channel and ﬁx it with the enclosed rubber tap. Recommended

position (h1, h2) of the feeler is marked on the drawing:

- If the feeler is mounted higher than recommended, the thermostat will react too fast,

the operating time of the circular pump will be shorter and the difference between the

temperature in the hot water tank and heating media after the thermostat switch off will be

higher. This means that the quantity of water in the hot water tank and its temperature will

be lower,

- If the feeler is mounted lower than recommended, the operating time of the circular pump

will be longer and the difference between the temperature in the hot water tank and

heating media after the thermostat switch off will be lower. This means that the quantity of

water in the hot water tank and its temperature will be little higher.

Thermometer

Heater SH

Heater R

CONNECTION TO THE WATER SUPPLY

Before connecting the hot water tank, install the protective covering. Take off the top cover

and insert the covering, make sure the slots on the covering match the connections on the

hot water tank. Zip the zipper from top to bottom and tighten the tapes on the top edge of the

covering. Replace the top cover. Insert the thermometer into the prefabricated sleeve on the

front of the hot water tank; make sure to cut the opening for the sleeve into the covering. The

connection to water supply network and fastening of the coloured rosettes shall be made

according to the markings deﬁned in previous Section.

For safety reasons the supply pipe must be ﬁtted with a return safety valve that prevents the

pressure in the tank from exceeding nominal pressure by more than 0.1 MPa. The heating of

water in the heater causes the pressure in the tank to increase to the level set by the safety

valve. As the water cannot return to the water supply system, this can result in dripping from

the outﬂow of the safety valve. The drip can be piped into the drain by installing a catching

unit just below the safety valve. The drainpipe ﬁtted under the safety valve outﬂow must be

piped down in a straight vertical line and located in an environment free from the onset of

freezing conditions.

In case the existing plumbing does not enable you to pipe the dripping water from the return

safety valve into the drain, you can avoid the dripping by installing expansion tank on the

inlet water pipe of the boiler. The volume of the expansion vessel shall be at least 3% of the

volume of the hot water tank.

Key:

1. Return safety valve

2. Test valve

3. Non-return valve

4. Pressure-reducing valve

5. Stop valve

6. Test unit

7. Funnel outlet to the drain

8. Drain valve

H - Cold water

T - Hot water

The water heater may be connected to the household water supply system without a

pressure-reducing valve provided the supply mains pressure is less than 0.5 MPa.

In case of the mains pressure exceeding 0.5 MPa, a pressure-reducing valve must be

installed to ensure that the pressure on the supply side of the heater does not rise above the

nominal value.

2T9

12 8

714 11 13

CONNECTION TO ALTERNATIVE SOURCES OF HEATING

The heaters enable the water for sanitary use to be heated by alternative sources of energy

(e.g. central heating, solar power, …) by installing one or two heat exchangers.

Additionally, a heating pump may also be ﬁtted to the side ﬂange of the tank.

Options for connecting the water heater to various sources of heating are shown in the

drawings below.

Connection to solar panels Connection to the

central heating hot-water system

1. Water heater

2. Central heating hot-water system

3. Solar panel

4. Differential thermostat with sensors (T1, T2, T3, T4)

5. Bypass pump

6. Expansion tank

7. Non-return valve

8. Safety valve

9. Air relief valve

10. Fill/drain valve

11. Reduction valve

12. Drain valve

13. Stop valve

14. Test unit

15. Funnel outlet to the drain

8 11 13

7 14

1287

141113

Connection to solar panels and central

heating hot-water system

OPERATION AND MAINTENANCE

The water heater is ready for use once it has been connected to water and other sources of

heating.

The usual main sources of heating of water for sanitary use are central heating or solar

power; in this case any regulation of water heating is performed in the heating system.

Electric heater type R may be additionally installed on the flange 180mm, or electric heater type

SH to the connecting bushing G 6/4, which are used for additional heating of water:

- If you need higher temperature of water than assured by other heating sources,

- If due to seasonal or other conditions there are no main heating sources.

In case of exposure to sub-zero temperatures, the water should be thoroughly drained from

the heater before the onset of freezing conditions.

Once that is done, open the hot water tap on one of the mixer taps connected to the water

heater. The water from the water heater drains by way of the drain valve on the inlet pipe.

External parts of the water heater may be cleaned with a mild detergent solution. Do not use

solvents and abrasive cleaners.

Regular preventive maintenance inspections ensure faultless performance and long life of

your heater. The ﬁrst of these inspections should be carried out by an authorised maintenance

service provider about two years from the date of installation in order to inspect the wear

of the corrosion protection anode and to remove any limestone as required. Build-up of

limestone is a product of quality, quantity and temperature of water ﬂowing through the water

heater. While inspecting the heater, the maintenance service provider will also recommend

the date of the next inspection.

Wear of the corrosion protection anode is carried out visually. Replacement is required when

the inspection reveals that the anode diameter has been substantially reduced or worn all

the way to the steel core.

Tank warranty is subject to regular inspections of the protective anode.

In the event of the water heater breaking down, you are kindly requested to contact

the authorised maintenance service provider located closest to you. Please do not

attempt to repair the unit yourself.

06/2008

766383

Gorenje Tiki, d.o.o.

SI-1521 Ljubljana

Magistrova 1

Slovenija

Telefon: +386 1 5005 600

Fax: +386 1 5005 702 382 012 722

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gorenje Boiler Handbücher

Gorenje

Gorenje EFWH SERIES Bedienungsanleitung

Gorenje

Gorenje TGRH 50 Bedienungsanleitung

Gorenje

Gorenje TC 200 Series Bedienungsanleitung

Gorenje

Gorenje TGR 30 S Bedienungsanleitung

Gorenje

Gorenje OTG SLIM SIMPLICITY Bedienungsanleitung

Gorenje

Gorenje Tiki GBFU50 Bedienungsanleitung

Gorenje

Gorenje TGR SUPER SLIM Bedienungsanleitung

Gorenje

Gorenje GWH NNBWC Series Bedienungsanleitung

Gorenje

Gorenje TGRK80LNG Bedienungsanleitung

Gorenje

Gorenje GT 10 U Bedienungsanleitung

Gorenje

Gorenje NRK-1 Bedienungsanleitung

Gorenje

Gorenje GWH12NFEAC Bedienungsanleitung

Gorenje

Gorenje GWHNNBW G20 Bedienungsanleitung

Gorenje

Gorenje GB 50 Bedienungsanleitung

Gorenje

Gorenje TGR30NG Bedienungsanleitung

Gorenje

Gorenje GBF 50 Bedienungsanleitung

Gorenje

Gorenje OTGS 30 E5 Bedienungsanleitung

Gorenje

Gorenje TCM 300 Series Bedienungsanleitung

Gorenje

Gorenje TGR SUPER SLIM UNI Bedienungsanleitung

Gorenje

Gorenje OTGS E5 Series Bedienungsanleitung

Gorenje

Gorenje TG 200 N Bedienungsanleitung

Gorenje

Gorenje GWH 10NNBWC Bedienungsanleitung

Gorenje

Gorenje GBK (V) Bedienungsanleitung

Gorenje

Gorenje TGRK120LNG Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung