Gossen MetraWatt DIGISKY Bedienungsanleitung

Revision level:

04-03.2014

Please checkthat the exposuremeter and accessories as

detailed below are included inthe box. If thecontents are

incomplete, pleasecontact your local dealer.

DIGISKY

V070A rechargeable battery

Power supply and USB connector cable

Carrying strap

CD ROM (includes operating instructions)

Quick-start guide

DIGISKY

Quick-start Guide –15448 –V1.18

Contents

Page

Preparation

Meter Overview

Measuring Modes

Function Selection

AmbientLight

Flash Light

MOVIE

Main Menu

FCC & IC (USA)

Safety Precautions

Preparations required for use of the exposure

meter and its basic functions are described in

these instructions.

Please read the

operating instructions

(on the CD) first.

Essentials

2 GOSSEN Foto- und Lichtmesstechnik GmbH

How to insert and charge the battery

The DIGISKY works with a device-specific, rechargeable lithium-

ion battery. Use the V070A rechargeable battery and the USB

battery charger included with the exposure meter.

In order to insert the rechargeable battery, it is necessary to

have a (Philips) recessed head screwdriver.

Switch your DIGISKY off or wait until the exposure meter is

switched off automatically.

Unscrew the battery cover at the back of the meter with a

(Philips) recessed head screwdriver, and then pull it down and

out of the housing.

Insert the battery into the compartment as shown in the figure.

Make sure that the battery is inserted with correct polarity

(+ and –)! Then place the battery cover over the battery

compartment and secure it with the screw.

Connect the cable to the USB port at the exposure meter first,

and then insert the mains plug into an electrical outlet.

The battery can also be charged using a USB port at a PC.

Remove the mains plug to this end, and connect the USB plug to

your PC.

The charging indicator lights up red while the battery is charging.

After the battery has been fully charged, the indicator will light up

green.

To protect the battery pack and prolong its life, do not

charge it for longer than 24 hours without break.

1 Unscrew

2 Remove cover

3 Insert battery

GOSSEN Foto- und Lichtmesstechnik GmbH 3

Switch DIGISKY off

Incident light,

flat diffuser

Meter Overview

Diffuser ring for incident

light/ reflected light

measurement, off

LEDs for status

of the meter

Display panel

Data key

Ring controller

Socket for connecting

flash synchronizing cable

Carrying strap

holder

USB port for charging battery

or data transmission

Meter cell f. reflected

light measurement

Menu key

Measurement key

User

Cam 1

Cam 2

Cam 3

Movie

Retractable

diffuser head

f.spherical/

flat /reflected

measurement

ISO

speed

Measuring

function

Measured

values

Analog scale

Cor.

Batt.

Incident light

Spherical diffuser

Reflected light

4 GOSSEN Foto- und Lichtmesstechnik GmbH

Function Selection: Ambient Light / Flash Light

Use the menu key ...

to select a function.

Measuring Modes

Spherical incident light

measurement

. Reflected light meas.

Flat incident light meas

Off

DIGISKY off

RF Function Selection: All / Group

Use the data key ...

to select “All” or a group.

Switching the DIGISKY on after:

Standby (display off)

Activate by pressing any key or turning the instrument head

Automatic switching OFF

Activate with menu key only

Manual switching OFF

Turn instrument head to measurement modes

GOSSEN Foto- und Lichtmesstechnik GmbH 5

Ambient Light

Use the ring

controller ...

to set time /

f-stop

Use the ring

controller ...

to select the desired

value.

Press the measurement key to make a measurement.

Contrast measurement: press and hold the measurement key.

Contrast measurement: use the data key to display the average, minimum and maximum value.

6 GOSSEN Foto- und Lichtmesstechnik GmbH

Flash light

Use the ring

controller ...

to select the desired

synchronization

speed.

Use the data key ...

to select the desired

group.

Press the measurement key ...

to perform a measurement.

NonCord

Approx. 45 seconds measurement standby duty

Cord

Synchronizing cable –flash is triggered

RF module –flash is triggered

GOSSEN Foto- und Lichtmesstechnik GmbH 7

Movie

Settings (f-stop, sector angle, sensitivity etc.) are set in the main menu.

EV analog display

Illuminance,

luminance

Measured value with

correction

Press the measurement key to perform a measurement.

For continuous measurement: press and hold the measurement key;

use data key to display the average, minimum and maximum value.

Use the menu key ...

to switch the display

from f-stop value to

photometric value.

Shutter

angle

CINE Speed

8 GOSSEN Foto- und Lichtmesstechnik GmbH

Main Menu

Press and hold menu key ...

to select a menu.

Use the ring controller ...

to select a user.

to select a setting.

Use the ring controller ...

Press the measurement key ...

to confirm.

to select a submenu.

Use the measurement key ...

to exit the menu.

to select a value.

GOSSEN Foto- und Lichtmesstechnik GmbH 9

FCC & IC - USA

Modifications

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to

operate the equipment.

Conditions of

Operations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

15.105

Class B digital device

or peripheral

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

15.105

Class A digital device

or peripheral

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

10 GOSSEN Foto- und Lichtmesstechnik GmbH

Safety Precautions

In the event of malfunctioning, switch the light meter off immediately.

If the event that smoke develops or unusual odors become apparent, which are caused by either the measuring instrument or the power

supply, disconnect from mains power immediately and remove the rechargeable battery from the instrument in order to prevent possible

fire. Continuing to operate the measuring instrument or the power supply after such malfunctions have occurred may result in severe

injury. Please contact your local dealer or Gossen-Service in order to eliminate malfunctioning. If you bring or send the instrument in for

repairs, make sure that the rechargeable battery has been removed first.

Never use the measuring instrument in proximity to flammable gases.

Electronic devices must not be used near flammable gases. Otherwise there would be danger of explosion and fire.

Never hang the meter and/or the carrying strap around the head or neck of a child.

Danger of strangulation exists if the carrying strap is hung around the head or neck of a child.

Displaying Documentation in PDF Format

Adobe Reader or Adobe Acrobat Reader must be installed to your PC if you want to display product documentation in PDF

format. If this software has not already been installed to your PC, it can be downloaded from the following website:

http://www.adobe.com.

This icon indicates that this product must be disposed of separately.

The following must be observed by users in European countries:

This product may only be disposed of separately at a designated collection point. It may not be disposed

of with household trash.

For further information contact your local dealer or waste disposal authorities.

Andere Handbücher für DIGISKY

Inhaltsverzeichnis

Andere Gossen MetraWatt Messgerät Handbücher

Gossen MetraWatt

Gossen MetraWatt Luna-star F Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PROFITEST MBASE MTECH Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRA HIT 22S Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAPHASE 1 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAFLEX 3000 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRISO C Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAHIT WORLD Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOWATT 230 Betriebsanleitung

Gossen MetraWatt

Gossen MetraWatt CLIMO FM Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-SPOT 2 USB Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOLUX 5032C USB Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt SECUTEST PRO Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 85 Leitfaden

Gossen MetraWatt

Gossen MetraWatt PROFITEST Series Originalbetriebsanleitung

Gossen MetraWatt

Gossen MetraWatt mavolog pro Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt DIGISKY Technisches Handbuch

Gossen MetraWatt

Gossen MetraWatt LonWorks ENERGYMID U228 W1 Series Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt PhaseCop2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVO-SPOT 2 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAport 40S Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt MAVOLUX 5032B USB Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRACLIP 87 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt LINAX 4000L Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAFLEX 300MXBL Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung