Graco 224667 Bedienungsanleitung

Instructions – Parts List

Fas-VactEvacuation System

For Oils and Heavier Lubricants

FOR LUBRICATION PRODUCTS ONLY

50 psi (3.5 bar, .35 MPa) Maximum Working Pressure

Model 224667

Basic Pump: Includes Husky 716

pump and mounting hardware

Model 224700, 16 Gallon System with Drum

Includes basic pump, dolly, wand storage kit,

and 1/4” x 32” suction wand and 16 gallon drum

Model 224701, 55 Gallon System

Includes basic pump, 55 gallon drum truck,

wand storage kit, and 1/2” x 32” suction wand.

308154F

Important Safety Instructions.

Read all warnings and instructions in this manual.

Save these instructions.

Table of Contents

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 11. . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Information 12. . . . . . . . . . . . . . . . . . . . . . .

9273A

Model 224701 shown

(does not include drum or

Filter-Regulator-Lubricator Kit)

2 308154

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

DThis equipment is for professional use only.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

DDo not alter or modify this equipment.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DHandle hoses carefully. Do not pull on hoses to move equipment.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose

Graco hoses to temperatures above 66_C (150_F) or below –40_C (–40_F).

DDo not move or lift pressurized equipment.

DComply with all applicable local, state, and national fire, electrical, and safety regulations.

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re-

sult in a fire or explosion and serious injury.

DGround all equipment. Refer to Grounding on page 3.

DIf there is any static sparking or you feel an electric shock while using this equipment, stop dis-

pensing immediately. Do not use the equipment until you identify and correct the problem.

DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid

being dispensed.

DKeep the dispense area free of debris, including solvent, rags, and gasoline.

DDo not smoke in the dispense area.

DDo not turn on or off any light switch in the dispense area while dispensing or while operating if

fumes are present.

3308154

WARNING

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin and

cause serious injury.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DDo not point the dispensing valve at anyone or at any part of the body.

DDo not put your hands or fingers over the grease fitting coupler.

DTighten all fluid connections before operating the equipment

DCheck the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,

inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,

state and national guidelines.

DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and

solvent manufacturer.

Installation

General Information

NOTE: Reference numbers and letters in parenthesis

in the text refer to callouts in the figures and the parts

drawing.

NOTE: Always use genuine Graco Parts and Accesso-

ries, available from your Graco distributor.

Grounding

WARNING

FIRE AND EXPLOSION HAZARD

Before operating the pump, ground the

system as explained below. Also read

the section FIRE OR EXPLOSION HAZ-

ARD on page 2.

1. Pump: Connect a ground wire (A) to the pump as

shown in Fig. 1. Connect to the other end to a true

earth ground. Order Grounding Kit (Part No.

222084)

2. Air Compressor: Follow the manufacturer’s recom-

mendations.

3. Use only metal or conductive containers.

4. All solvent pails used when flushing, according to

local code. Use only metal pails, which are con-

ductive. Do not place the pail on a non-conductive

surface, such as paper or cardboard, which inter-

rupts the grounding continuity.

9247A

Fig 1

4 308154

Installation

9274A

101

204,205

203

202

104

103

202

206

Fig 2

NOTE: Fig. 2 shows the 55 Gallon Unit, Model

224701. See Fig. 3 for the 16 Gallon Unit, 224700.

1. Install the wheels on the dolly, or assemble the

truck according to the instructions supplied with it.

2. Put the drum on the dolly or truck. The truck has a

chain and clip (A) to secure the drum.

3. Position the pump between the bung hole and vent

hole of the drum as shown in Figs. 2 and 3. Loos-

en the top screw (14) of each pump clamp (18),

and reposition the clamps as needed to fit the rim

of the drum. Tighten the screws (17) to secure the

pump to the rim of the drum.

4. Install the wand storage tube (supplied). Place the

holder (206) on the lip of the dolly or truck. Place

the tube (202) in the holder, and slide the

bracket (203) over the tube. Align the bracket to

the holder, and secure the bracket to the rim of the

drum.

5. Remove the drum’s vent hole cover, and install the

vented fluid gauge (23).

6. Remove the drum’s bung hole cover and install the

plug (24). Put the 50” drain hose (1) into the drum

through the bung hole.

7. Connect a wand (104)to the quick coupler (7).

Store the wand in the storage tube (202) until

needed.

5308154

Installation

9275A

104

202

203

206

105

204,205

101

Fig 3

Air Regulation

If you are using the optional air line Filter-Regulator-

Lubricator Kit 110149, see page 6 for installation

instructions.

If you are providing your own regulation, you should

install a quick disconnect coupler at the air hose and

pump inlet or regulator.

Optional Fluid Filter For Evacuation Mode

When evacuating particle-contaminated lubricants

from the 16 or 55 gallon drum to another container,

use a suction hose with filter, Kit 223888, to prevent

damage to the pump.

6 308154

Installation

Adding an Optional Air Line

Filter-Regulator-Lubricator (FRL) Kit

Proper conditioning of compressed air help prolong the

life of your pump. In the FRL Kit, the filter removes

harmful dirt and moisture from the compressed air, the

regulator controls air to the pump, and the lubricator

provides automatic motor lubrication.

Graco’s FRL (Part No. 110149) should be mounted to

the Fas-Vac with the Mounting Kit (Part No. 224759)

1. Remove the two manifold screws, flat washers,

and lockwashers (A) from the pump. Install the

accessory bracket (B) so that its large hole faces

up. Install the screws and lockwashers (do not use

the flat washers).

2. Remove the male quick disconnect fitting (20) from

the pump, and install it in the air filter inlet (J).

3. Hold the FRL with the air filter (H) to the left. Install

the gauge (C) in the back port of the regulator (not

the top), and turn it so the gauge faces up. Install

the plug (G) in the front port of the gauge.

4. Remove the lock ring (F) from the base of the air

regulator knob.

5. Angle the FRL into the bracket so the gauge slides

into the slot in the bracket. Screw the lock

ring (F) over the regulator knob to secure the

assembly to the bracket.

6. Install a 90_nylon connector (E) to the FRL outlet

on the side of the lubricator. Install the other

connector to the pump air restrictor inlet (not

visible in Fig. 4). Tighten the connectors in a

position that allows easy installation of the nylon

tube (D). Install the tube.

9272A

Fig 4

AB C D

7308154

Operation

Control Knob

The Fas-Vac system operates in two modes: evacuate

lubricants from a crankcase or reservoir and collect the

material in a 16 gallon or 55 gallon drum, and drain the

stored lubricants from the drum to a larger container.

The modes are selected with a lock-in-place control

knob (A). See Fig. 5.

When the system is not in use, lock the knob in evacu-

ation mode.

Suction Wands

Experiment to determine which wand is best for your

application. Typically, use the largest wand possible. A

quick-disconnect coupler makes it fast and easy to

switch wands.

Fluid Gauge

The fluid gauge (23) indicates approximately how full

the drum is to avoid over-filling it. See Fig. 5. When its

red cap is even with the top, the drum will be 75% to

80% full.

Evacuation

1. Check the gauge level.

2. Be sure that the control knob (A) is in the

EVACUATION position and the safety clip (8) locks

it in place. See Fig. 5.

3. Connect the air supply hose to the pump air

inlet (B). Operate the pump at 40–50 psi

(2.72–3.4 bar, 0.27–0.34 MPa) For the best re-

sults.

4. Insert the suction wand (104) in the crankcase or

reservoir.

5. Disconnect the air to the pump when the evacua-

tion is complete.

Draining the Drum

1. Remove the suction wand (104). Attach the suc-

tion hose quick-disconnect coupler to the male

coupler fitting of a waste oil tank, or discharge the

material to an access opening.

2. Pull out the safety clip (8), and turn the control

knob (A) to DRAIN DRUM. See Fig. 5.

3. Connect the air supply hose to the pump.

4. When the draining is complete, disconnect the air

to the pump, turn the valve knob (A) back to the

evacuation position, and install the safety clip (8).

Fig 5

(when using FRL kit)

23 104

9273A

8 308154

Parts

Model 224701

55 Gallon System

Includes items 101 to 104

Ref

No. Part No. Description Qty

101 224667 PUMP

See page 10 for parts 1

102 224666 WAND STORAGE KIT

Includes items 201 to 206 as shown

on page 11 1

103 111470 55 GALLON DRUM TRUCK 1

104 224702 WAND, 32” x 1/2” OD

Includes items 301 to 303 as shown

on page 11 1

9274A

101

Ref 23

Ref 24

104

103

Part of 102

Ref 1

Ref 7

Part of 102

9308154

Parts

Model 224700

16 Gallon Fas-VacTM System, with drum

Includes items 101 to 105

Model 224665

16 Gallon Deluxe Dolly

Includes items 103a to 103f

Ref

No. Part No. Description Qty

101 224667 PUMP ASSEMBLY 1

See parts on page 10

102 224666 WAND STORAGE KIT 1

Includes items 201 to 206 as shown

on page 11

103 224665 DOLLY, 16 gallon deluxe 1

Includes items 103a to 103f

103a 205419 . CLAMP, dolly, 120 lb. 1

103b 111472 . CASTER, 3” 4

103c 100307 . NUT, full, hex, 3/8–16 unc–2b 1

103d 100023 . WASHER, flat, 3/8” 1

103e 102971 . BOLT, carriage, 3/8–16 unc–2a x 3” 1

103f 101185 . BOLT, carriage, 3/8–16 unc–2a x 4” 1

104 224669 WAND, 32” x 1/4” OD

Includes items 301 to 303 as

shown on page 11 1

105 111468 DRUM, 16 gallon 1

9275A

Ref 4

104

103a

103b

105

Ref 24

Ref 23

Ref 1

101

Part of 102

103c,103d, and103e or 103f

10 308154

Parts

9276A

11 12

717

LABEL

BRACKET

Model 224667

Basic Pump

Ref

No. Part No. Description Qty

Ref

No. Part No. Description Qty

1 111475 HOSE, cpld 1/2 npt,

50” (1.3 m) long 1

2 111473 HOSE, cpld 1/2–14 npt x

3/8–18 npt, 10 ft (3 m) long 1

3 108479 SCREW, mach, hex hd;

10–24 UNC–2a x 3/4” 2

4 187355 BRACKET 1

5 187350 LABEL, instruction 1

6 187366 SPACER 2

7 801569 COUPLER, quick disconnect 1

8 111465 CLIP, hitch pin 1

9 101577 SCREW, mach, hex hd,

10–24 unc–2a x 3/8” 1

10 111466 CHAIN, ball 1

11 156684 UNION, adapter, 1/2 npt(m) x

1/2 npt(f) swivel 1

12 157191 ADAPTER, 1/2–14 npt(m)

x 3/4 –14 npt(m) 1

13 170709 FOOT 2

14 100333 CAPSCREW, hex hd;

1/4–20 unc–2a x 5” long 2

15 100016 LOCKWASHER, 1/2” 2

16 100527 WASHER, PLAIN, 5/16” 2

17 100057 CAPSCREW, hex hd;

5/16–18 UNC–2a 2

18 187354 BRACKET, mounting 2

19 241906 HUSKY 716 PUMP

See manual 308573 for parts 1

20 169970 FITTING, air line 1

21 111474 HOSE, cpld 1/2–14 npt x

3/4–14 npt, 20” (0.5 m) long 1

22 103473 STRAP, wire tie (not shown) 1

23 111467 GAUGE, drum fill 1

24 183553 PLUG, bung 1

25 187359 4-WAY VALVE 1

Andere Handbücher für 224667

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Industrieanlagen Handbücher

Graco

Graco 25M713 Bedienungsanleitung

Graco

Graco Therm-O-Flow 5 918343 Bedienungsanleitung

Graco

Graco 116229 Bedienungsanleitung

Graco

Graco Delta Spray 240-686 Bedienungsanleitung

Graco

Graco Reactor H-25 Series Bedienungsanleitung

Graco

Graco Reactor 2 Gebrauchs- und Pflegehandbuch

Graco

Graco 24J163 Bedienungsanleitung

Graco

Graco 970196 Bedienungsanleitung

Graco

Graco THERM-O-FLOW 234239 Bedienungsanleitung

Graco

Graco LSA 200 Bedienungsanleitung

Graco

Graco Ex35 Bedienungsanleitung

Graco

Graco 25C483 Bedienungsanleitung

Graco

Graco Magnum B Series Bedienungsanleitung

Graco

Graco 243701 Datenblatt

Graco

Graco 246477 Bedienungsanleitung

Graco

Graco Xtreme Mix Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Fire-Ball 222073 Bedienungsanleitung

Graco

Graco SERIES J Bedienungsanleitung

Graco

Graco Therm-O-Flow 20 Stücklistenhandbuch

Graco

Graco ExactaBlend AGP Bedienungsanleitung

Graco

Graco SaniForce STU Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco HydroShield 26D030 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung