Graco 243279 Bedienungsanleitung

Instructions–Parts List

309196F

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

55 GALLON STANDARD DRUM

Hot Melt Wiper Kits

Designed to fit straight sided drums with a 22.5” (571 mm) ID

Model 243279 (built prior to May 2006)

Model 253292 (built May 2006 and after)

Dual Tee Wipers

Maximum Temperature 250_F (121_C)

Model 245668 (built prior to May 2006)

Model 253290 (built May 2006 and after)

Tee Wiper / Steam Hose

Maximum Temperature 375_F (190_C)

Model C31007 (built prior to May 2006)

Model 253291 (built May 2006 and after)

Silicone Hose / Steam Hose

Maximum Temperature 400_F (204_C)

Model 234995 (built prior to May 2006)

Model 253289 (built May 2006 and after)

Spring / Hose Wipers

Maximum Temperature 400_F (204_C)

Table of Contents

Symbols 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Related Publications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Standard Warranty 16. . . . . . . . . . . . . . . . . . . . . .

Graco Information 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TI0410

2 309196

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

HOT SURFACE AND FLUID HAZARD

Heated fluid can cause severe burns and can cause equipment surfaces to become very hot.

DWear protective gloves and clothing when operating this equipment in a heated system.

DDo not touch the metal heat sink when the surface is hot.

DAllow the equipment to cool thoroughly before servicing.

Some heated systems are designed to dispense Polyurethane (PUR) heated materials. PUR

systems are supplied with ventilation hoods, and require proper ventilation and specially designed

system components.

MOVING PARTS HAZARD

Moving parts, such as the ram plate and pump inlet, can pinch or amputate your fingers.

DKeep clear of all moving parts when starting or operating the equipment.

DKeep hands and fingers away from the priming piston during operation and whenever the pump

is charged with air.

DKeep clear of the ram plate, pump fluid inlet, and lip of the fluid container when raising or lower-

ing the ram.

Related Publications

Form Name Form#

Therm–O–Flow Installation and Operation 309180

Therm–O–Flow Installation and Operation 311208

309196 3

Installation

Twin Tee Wiper Kit 243279 / 253292

Clean the seal groves as follows:

1. Using a wooden or plastic tool to prevent damage

to the wiper, clean all material from the seal

grooves.

2. Lubricate ram plate grooves, bands, and wipers

before assembly.

Install the wiper ring seals as follows:

NOTE: Wipers are marked top and bottom for 243270.

253292 uses the same wiper top and bottom.

1. Pull the top wiper over the platen assembly. Roll

the first wiper ring (10) down to the top ring groove

as shown in Fig. 1.

2. Install the first upper band (20) over the wiper ring,

placing it in the top groove of the wiper.

CAUTION

Do not over tighten the screw in the band. Over tight-

ening the screw will deform the wiper ring.

3. Secure the top band using the screw in the band.

4. Install the second upper band onto the bottom of

the wiper ring on the top groove of the wiper ring.

5. Secure the top band using the screw in the band.

6. Roll the second wiper ring up from the bottom of

the plate to the bottom ring groove.

7. Install the first lower band over the wiper ring on

the bottom groove, placing it in the top groove of

the bottom wiper.

CAUTION

Do not over tighten the screw in the band. Over tight-

ening the screw will deform the wiper ring.

8. Secure the lower band using the screw in the

band.

9. Install the second lower band onto the bottom of

the wiper ring on the bottom groove of the wiper

ring.

10. Secure the lower band using the screw in the

band.

CAUTION

Make sure the wipers are lubricated. Without lubrica-

tion, the wipers may tear.

11. Using a lubricant compatible with the material to

be pumped, lubricate the ram plate wipers.

ÉÉÉÉ

03288

Fig. 1

4 309196

Installation

Tee Wiper / Steam Hose Kit 245668 /

253290

Clean the seal grooves as follows:

1. Using a wooden or plastic tool to prevent damage

to the wiper, clean all material from the seal

grooves.

2. Lubricate ram plate grooves, bands, and wipers

before assembly.

Install the wiper ring seals as follows:

NOTE: Upper wiper is tee, lower is hose.

1. Pull the tee wiper over the platen assembly. Roll

the tee wiper ring (10) down to the top ring groove

as shown in Fig. 2.

2. Install the first upper band (20) over the wiper ring,

placing it in the top groove of the wiper.

CAUTION

Do not over tighten the screw in the band. Over tight-

ening the screw will deform the wiper ring.

3. Secure the top band using the screw in the band.

4. Install the second upper band onto the bottom of

the wiper ring on the top groove of the wiper.

5. Secure the top band using the screw in the band.

CAUTION

Make sure the wipers are lubricated. Without lubrica-

tion, the wipers may tear.

6. Assemble and cut band as shown in Fig. 2.

7. Install screw jack in slot. Tape around tab in slot.

8. Install hose and band so that angled ends of hose

press against each other.

9. After installing clamp, work hose with mallet to

completely close gap at the ends.

10. Hose seam must be in line with tie rod holes

[+ or – 1” (25.4 mm)].

TI2345

Fig. 2

ÉÉÉÉ

Wrap tape

around insert tab

Cut between

slots as shown

309196 5

Installation

Silicone Hose / Steam Hose Kit C31007 /

253291

Clean the seal grooves as follows:

1. Using a wooden or plastic tool to prevent damage

to the wiper, clean all material from the seal

grooves.

2. Lubricate ram plate grooves, bands, and wipers

before assembly.

Install the wiper ring seals as follows:

NOTE: Upper wiper is green hose, lower is black hose.

1. Assemble and cut band as shown in Fig. 3.

2. Install screw jack in slot. Tape around tab in slot.

3. Install hose and band so that angled ends of hose

press against each other.

4. After installing clamp, work hose with mallet to

completely close gap at the ends.

5. Hose seam must be 180_apart, and in line with tie

rod holes [+ or – 1” (25.4 mm)].

TI2345

Fig. 3

ÉÉÉÉ

Wrap tape

around insert tab

Cut between

slots as shown

6 309196

Installation

Spring / Hose Wipers Kit 234995 / 253289

Clean the seal grooves as follows:

1. Using a wooden or plastic tool to prevent damage

to the wiper, clean all material from the seal

grooves.

2. Lubricate ram plate grooves, springs, and wipers

before assembly.

Install the wiper ring seals as follows:

1. Install hose and spring so that the angled ends of

the hose press against each other.

2. After installing spring (Fig. 4), work hose with

mallet to completely close gap at the ends.

3. Hose seam must be 180_apart, and in line with tie

rod holes [+ or – 1” (25.4 mm)].

Fig. 4

Spring

Hose

ti1595a

309196 7

Parts

Model 243279

Dual Tee Wipers

TI0410

Ref.

No. Part No. Description Qty.

10 115656 SEAL, wiper ring, upper 1

20 115658 BAND, wiper ring, upper 2

Ref.

No. Part No. Description Qty.

30 115655 SEAL, wiper ring, lower 1

40 115657 BAND, wiper ring, lower 2

8 309196

Parts

Model 245668

Tee Wiper / Steam Hose

TI2346

Ref.

No. Part No. Description Qty.

10 115656 SEAL, tee wiper 1

20 115658 BAND, wiper ring, upper 2

Ref.

No. Part No. Description Qty.

30 C31005 HOSE, follower, lower 1

40 C33040 CLAMP, kit, single seal 1

309196 9

Parts

Model C31007

Silicone Hose / Steam Hose

TI2346

Ref.

No. Part No. Description Qty.

10 C31002 CLAMP, tire 1

20 C31003 HOSE, follower, upper 1

Ref.

No. Part No. Description Qty.

30 C31005 HOSE, follower, lower 1

10 309196

Parts

Model 234995

Spring / Hose Wipers

ti1594a

Ref.

No. Part No. Description Qty.

10 119415 SPRING, wiper retaining 2

20 119414 HOSE, follower, lower; 3/4” 1

Ref.

No. Part No. Description Qty.

30 119413 HOSE, follower, upper; 1” 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Industrieanlagen Handbücher

Graco

Graco PRESIDENT 231-920 Bedienungsanleitung

Graco

Graco Delta Spray 240-686 Bedienungsanleitung

Graco

Graco Xtreme Mix Bedienungsanleitung

Graco

Graco Reactor 2 Gebrauchs- und Pflegehandbuch

Graco

Graco King E60 Bedienungsanleitung

Graco

Graco Falcon Bedienungsanleitung

Graco

Graco SaniForce SDU Series Stücklistenhandbuch

Graco

Graco SaniForce STU Bedienungsanleitung

Graco

Graco 253479 Bedienungsanleitung

Graco

Graco Viscount I Stücklistenhandbuch

Graco

Graco Twistork 235534 Bedienungsanleitung

Graco

Graco C Series Stücklistenhandbuch

Graco

Graco 204-352 Bedienungsanleitung

Graco

Graco RTX 1500 Bedienungsanleitung

Graco

Graco 17B190 Bedienungsanleitung

Graco

Graco ExactaBlend AGP Bedienungsanleitung

Graco

Graco Power-Lock Stücklistenhandbuch

Graco

Graco DataTrak 24W477 Handbuch

Graco

Graco 24Y326 Handbuch

Graco

Graco Pulse 25T462 Bedienungsanleitung

Graco

Graco Reactor 3 E-20 Elite Bedienungsanleitung

Graco

Graco U-Cup Dura-Flo Lowers Bedienungsanleitung

Graco

Graco 918468 Datenblatt

Graco

Graco Dispensit 1053-10C Fehlerbehebungshandbuch

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung