Graco 222077 Bedienungsanleitung

307879

Rev. N

First choice when

quality counts.t

Model 226342

INSTRUCTIONS-PARTS LIST

INSTRUCTIONS

This manual contains important

warnings and information.

READ AND KEEP FOR REFERENCE.

15:1 RATIO FIRE-BALLR

Undercoater Pumps

2250 psi (16 MPa, 157 bar) Maximum Fluid Working Pressure

180 psi (1.2 MPa, 12 bar) Maximum Incoming Air Pressure

Portable and stationary units for filled undercoating materials.

Model No. Size, Type

Dis-

pense

Kit Cover

222077 35 lb, portable X X

226342 120 lb, rollaround X X

226269 400 lb, stationary X X

WARNING

These systems are designed to be used only

in pumping petroleum-based undercoating

materials. Any other use of the system can cause

unsafe operating conditions and result in

component rupture, fire, or explosion, which can

cause serious bodily injury, including fluid injection.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

Contents

Parts

2 307879

Table of Contents

Warnings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Drawings and Lists

Model 222077, 35-lb Pail Size Unit 9. . . . . . . . . . . . .

Dispense Kit 222079 9. . . . . . . . . . . . . . . . . . . . . . . . . .

Model 226342, 120-lb Drum Size Unit

with Dolly 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 226269, 400-lb Stationary Drum

Size Unit 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dispense Kit 222082 11. . . . . . . . . . . . . . . . . . . . . . . . .

Accessories 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Warranty 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number 14. . . . . . . . . . . . . . . . . . . . . . . .

307879 3

Warnings

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

INJECTION HAZARD

Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an

extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin

can also cause a serious injury.

DFluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medi-

cal attention.

DDo not point the dispensing valve at anyone or at any part of the body.

DDo not put hand or fingers over the spray tip.

DDo not stop or deflect fluid leaks with your hand, body, glove, or rag.

DDo not “blow back” fluid; this is not an air spray system.

DAlways have the tip guard and the trigger guard on the gun when spraying.

DBe sure the gun trigger safety operates before spraying.

DLock the gun/valve trigger safety when you stop spraying.

DFollow the Pressure Relief Procedure on page 7 whenever you: are instructed to relieve pres-

sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.

DTighten all the fluid connections before operating the equipment.

DCheck the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.

Permanently coupled hoses cannot be repaired; replace the entire hose.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the

skin, swallowed, or inhaled.

DKnow the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.

DStore hazardous fluid in an approved container. Dispose of the hazardous fluid according to all

local, state, and national guidelines.

DWear appropriate protective clothing, gloves, eyewear, and respirator.

4 307879

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and

result in fire or explosion and serious injury.

DGround the equipment and the object being sprayed. See Grounding on page 5.

DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being

sprayed.

DExtinguish all the open flames or pilot lights in the spray area.

DElectrically disconnect all the equipment in the spray area.

DKeep the spray area free of debris, including solvent, rags, and gasoline.

DDo not turn on or off any light switch in the spray area while operating or if fumes are present.

DDo not smoke in the spray area.

DDo not operate a gasoline engine in the spray area.

DIf there is any static sparking while using the equipment, stop spraying immediately. Identify and

correct the problem.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result

in a serious injury.

DThis equipment is for professional use only.

DRead all the instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are uncertain about usage, call your Graco

distributor.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck the equipment daily. Repair or replace worn or damaged parts immediately.

DThe maximum working pressure of the 15:1 Ratio Fire-Ball pumps is 2250 psi (16 MPa, 157 bar)

at a maximum air operating pressure of 180 psi (1.2 MPa, 12 bar). Never operate the pump at a

higher air or fluid working pressure. Do not exceed the maximum working pressure of the lowest

rated system component.

DUse fluids that are compatible with the equipment wetted parts. See the Technical Data section of

all the equipment manuals. Read the fluid manufacturer’s warnings.

DRoute the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not

expose Graco hoses to temperatures above 180_F (82_C) or below –40_F (–40_C).

DDo not use the hoses to pull equipment.

DWear hearing protection when operating this equipment.

DComply with all applicable local, state, and national fire, electrical, and other safety regulations.

United States Government safety standards have been adopted under the Occupational Safety and Health Act. You

should consult these standards––particularly General Standards, Part 1910, and Construction Standards, Part

1926.

307879 5

Installation

Grounding

WARNING

FIRE AND EXPLOSION HAZARD

Before operating, ground the system as

explained below. Also read the section

FIRE AND EXPLOSION HAZARD on

page 4.

Static electricity is created by the flow of fluid through

the pump and hose. If the pump is not properly

grounded, sparking may occur, and the system may

become hazardous. Sparking may also occur when

plugging in or unplugging a power supply cord. Sparks

can ignite fumes from solvents, dust particles and

other flammable substances, whether you are

operating indoors or outdoors, and can cause a fire or

explosion and serious bodily injury and property

damage.

To reduce the risk of static sparking, ground all the

dispensing equipment used or located in the work

area. Check you local electrical code for detailed

grounding instructions for your are and type of

equipment. Be sure to ground all of this equipment.

DPump or sprayer: If using an electric sprayer, plug

the power supply cord or extension cord, each

equipped with an undamaged three-prong plug, into

a properly grounded outlet. Do not use an adapter.

All extension cords must have three wires and be

rated for 15 amps. If using another type of sprayer

or pump, ground it by connecting a grounding wire

(12 ga minimum) from the pump or sprayer’s

grounding lug to a true earth ground.

DAir compressor or hydraulic power supply: Follow

the local code.

DFluid hoses: Use only electrically conductive hoses

with a maximum of 500 feet (150 m) combined

hose length to ensure grounding continuity.

DSpray gun: Obtain grounding through connection to

a properly grounded fluid hose and sprayer or

pump.

DSupply container: Follow the local code.

DObject being sprayed: Follow the local code.

DAll solvent pails used when flushing: Follow the

local code. Use only metal pails, which are

conductive. Do not place the pail on a

non-conductive surface, such as paper or

cardboard, which interrupts the grounding

continuity.

DTo maintain grounding continuity when flushing or

relieving pressure, always hold a metal part of the

gun firmly to the side of a grounded metal pail, then

trigger the gun.

To ground the pump, loosen the grounding lug

locknut (W) and washer (X). Insert one end of a

12 ga (1.5 mm2) minimum ground wire (Y) into the

slot (Z) in the lug, and tighten the locknut securely.

Connect the other end of the wire to a true earth

ground. To order a ground wire and clamp, order

Part No. 222011.

6 307879

Installation

Assembling the Unit

DRefer to the appropriate parts drawing on pages

9 through NO TAG to assemble your unit. Use

thread sealant on all male connections, except at

swivels.

DThe spray gun supplied with these units includes an

open style tip guard. For spraying undercoating

materials, remove that guard and use the

Reverse-A-Clean IV tip guard and tip, also

supplied.

DFor Models 222077 & 226269: Remove the cover

from the supply drum and install the pump and

cover. Tighten the cover thumbscrews.

DFor Model 226342 only: Assemble the dolly. Place

the opened drum on the dolly. Tighten the nut onto

the carriage bolt to secure the drum.

Air Line and Accessories

NOTE: Install the air line accessories in the order

shown in the Typical Installation drawing. See page

12 to order the accessories.

1. Install a pump runaway valve (G) to shut off the air

to the pump if the pump accelerates beyond the

pre-adjusted setting. A pump that runs too fast can

be seriously damaged.

2. Install an air line lubricator (F) for automatic air

motor lubrication.

3. Install the air regulator (C) to control pump speed

and pressure.

4. On the main air supply line from the compressor,

install an air line filter (E) to remove harmful dirt

and contaminants from your compressed air

supply.

CAUTION

Do not hang air accessories directly on the air inlet.

The fittings are not strong enough to support acces-

sories and may cause one or more to break. Provide

a bracket on which to mount accessories.

7308A

AKEY

AFluid dispense line

BPump ground wire

CAir regulator

DMain air supply line

EAir filter

FPump lubricator

GPump runaway valve

HFluid drain valve

JBleed-type master air valve

Typical Installation

GE F NOTE: This typical installation is only a guide

for selecting and installing a system; it is not an

actual system design. Contact your Graco

distributor for assistance in designing a system

to suit your needs.

307879 7

Operation

Pressure Relief Procedure

WARNING

INJECTION HAZARD

Fluid under high pressure can be in-

jected through the skin and cause seri-

ous injury. To reduce the risk of an injury

from injection, splashing fluid, or moving parts, fol-

low the Pressure Relief Procedure whenever you

DAre instructed to relieve the pressure

DStop spraying

DCheck or service any of the system equipment

DInstall or clean the spray tips

1. Engage the gun safety latch.

2. Shut off the power supply to the pump and open

any air bleed valves in the system.

3. Disengage the gun safety latch.

4. Hold a metal part of the gun firmly to the side of a

grounded metal pail, and trigger the gun to relieve

pressure.

5. Engage the gun safety latch.

6. Open the fluid drain valve, and have a container

ready to catch the drainage.

7. Leave the drain valve open until you are ready to

use the system again.

If you suspect that the gun, hose, or spray tip is

completely clogged, or that pressure has not been fully

relieved after following the steps above, very slowly

loosen the tip guard retaining nut, outlet accessory nut,

or hose end coupling, and relieve pressure gradually,

then loosen completely, then clear the tip or hose.

8 307879

Operation

Start-up: Single or Multiple Pump Systems

1. Close the air regulators and bleed-type master air

valves to all but one pump.

2. Open the master air valve from the compressor.

3. For the pump that is connected, trigger the

dispensing valve into a grounded metal waste

container, making firm metal-to-metal contact

between the container and valve. Open the

bleed-type master air valve and open the pump air

regulator slowly, just until the pump is running.

When the pump is primed and all air has been

pushed out of the lines, release the trigger.

4. If you have more than one pump, repeat this

procedure for each pump.

NOTE: When the pump is primed, and with sufficient

air supplied, the pump starts when the dispensing

valve is opened and shuts off when it is closed.

5. Set the air pressure to each pump at the lowest

pressure needed to get the desired results.

WARNING

The maximum working pressure of each pump in

your system may not be the same. To reduce the

risk of over-pressurizing any part of your system,

be sure you know the maximum working pressure

rating of each pump and its connected compo-

nents. Never exceed the maximum working pres-

sure of the lowest rated component connected to a

particular pump.

To determine the fluid output pressure using the air

regulator reading, multiply the ratio of the pump by

the air pressure shown on the regulator gauge. For

example:

10:(1) ratio x 100 psi air =1000 psi fluid output

[10:(1) ratio x 7 bar air = 70 bar fluid output]

[10:(1) ratio x 0.7 MPa air = 7 MPa fluid output]

Limit the air to the pump so that no air line or fluid

line component or accessory is over-pressurized.

6. If your pump accelerates quickly, or is running too

fast, stop it immediately and check the fluid supply.

If the supply container is empty and air has been

pumped into the lines, prime the pump and lines

with fluid, or flush it and leave it filled with a

compatible solvent. Be sure to eliminate all air

from the fluid system.

Never allow the pump to run dry of the fluid being

pumped. A dry pump quickly accelerates to a high

speed, possibly damaging itself, and it may get

very hot.

CAUTION

NOTE: A pump runaway valve can be installed on the

air line to automatically shut off the pump if it starts to

run too fast. See Accessories, page 12.

7. Read and follow the instructions supplied with

each component in your system.

8. Whenever you shut off the system, always follow

the Pressure Relief Procedure.

WARNING

To reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure at left.

307879 9

Parts

7304A

Model 222077

35-lb Pail Size Unit

Ref

No. Part No. Description Qty

1 206405 PUMP, 15:1 Ratio Fire-ball;

See 306531 for parts. 1

2 222079 DISPENSE KIT;

See Parts List at right. 1

3 222058 COVER; Includes items 3a to 3d 1

3a 206522 SCOVER, pail 1

3b 100220 STHUMBSCREW 3

3c 100916 SLOCKWASHER 2

3d 100922 SCAPSCREW 2

Dispense Kit 222079

Ref

No. Part No. Description Qty

101 109075 AIR REGULATOR;

See 307204 for parts. 1

102 208536 COUPLER, quick disconnect 1

103 204940 SWIVEL; See 306861 for parts. 1

106 156971 NIPPLE, 1/4 npt 1

107 109165 HOSE, fluid, cpld 1

108 210890 SPRAY GUN;

See 307260 for parts. 1

109 156849 NIPPLE, 3/8 npt 1

110 104984 TEE, pipe; 1/4 npt 1

111 210657 BALL VALVE;

See 306861 for parts. 1

112 100940 ELBOW, street; 1/4 npt 1

113 169971 FITTING, pin 1

1112 111 107

110

108

102 113

101

109

103

106

10 307879

Parts

7307A

Model 226342

120-lb Drum Size Unit with Dolly

Ref

No. Part No. Description Qty

1 206699 PUMP, 15:1 Ratio Fire-ball;

See 306531 for parts. 1

2 222079 DISPENSE KIT;

See Parts List on page 9. 1

3 204574 COVER; See 306345 for parts. 1

4 204144 BASE, dolly;

Includes items 4a to 4d 1

4a 100023 WASHER, flat; 5/16”1

4b 100307 NUT, full hex; 3/8–16 1

4c 101851 CASTER, wheel, 2 1/2”dia. 4

4d 102971 BOLT, carriage; 3/8–16 x 3”1

4e 205419 CLAMP, dolly 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Reactor H-30 Elite Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

Graco

Graco E-Flo 4000 Bedienungsanleitung

Graco

Graco Power-Flo Series Bedienungsanleitung

Graco

Graco Husky 515 series Bedienungsanleitung

Graco

Graco E-Flo Bedienungsanleitung

Graco

Graco fire-ball 425 Bedienungsanleitung

Graco

Graco saniforce 2150 Handbuch

Graco

Graco Triton 308HP Bedienungsanleitung

Graco

Graco GBL 7500 Bedienungsanleitung

Graco

Graco Hydra-Clean 1040 Bedienungsanleitung

Graco

Graco PRESIDENT 207-706 Bedienungsanleitung

Graco

Graco Check-Mate 200 A Series Bedienungsanleitung

Graco

Graco 24R253 Bedienungsanleitung

Graco

Graco Fire-Ball 300 Bedienungsanleitung

Graco

Graco 260550 Bedienungsanleitung

Graco

Graco G3 Series Bedienungsanleitung

Graco

Graco Merkur W10CAS Bedienungsanleitung

Graco

Graco 205394 Bedienungsanleitung

Graco

Graco Dyna-Star A Series Bedienungsanleitung

Graco

Graco ToughTek SL340e Bedienungsanleitung

Graco

Graco Series B Bedienungsanleitung

Graco

Graco Check-Mate 2100 A Series Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung