Graco Fire-Ball B Series Bedienungsanleitung

Instructions – Parts List

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

10:1 Fire–Ballr425 Pump

Low–pressure, medium volume pump used to transfer grease.

1800 psi (12.4 MPa, 124 bar) Maximum Working Pressure

180 psi (1.3 MPa, 13 bar) Maximum Air Inlet Pressure

Model No. 965124, Series B, Stubby length

Model No. 965129, Series B, 400 lb (180 Kg) drum length

For Closed Drum Mounting

309407E

Important Safety instructions.

Read all warnings and instructions in this manual.

Save these instructions.

WARNING

This pump is designed to be used only in pumping

non-corrosive and non-abrasive lubricants. Any

other use of the pump can cause unsafe operating

conditions and component rupture, which can re-

sult in fluid injection or other serious injury or fire or

explosion.

TI2146A

2 309407

Table of Contents

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Standard Warranty 18. . . . . . . . . . . . . . . . . . . . . .

Graco Information 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

SKIN INJECTION HAZARD

High–pressure fluid from dispense device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgi-

cal treatment.

DDo not point the dispensing device at anyone or any part of the body.

DDo not put your hand over the end of the fluid outlet.

DDo not stop or deflect leaks with your hand, body, glove, or rag.

DFollow the Pressure Relief Procedure on page 7 before you clean, check, or service the

equipment.

DTighten all fluid connections before operating the equipment.

DCheck the hoses and couplings daily. Replace worn or damaged parts immediately.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers.

DKeep clear of all moving parts when starting or operating the pump.

DBefore checking or servicing the equipment, follow the Pressure Relief Procedure on page 7 to

prevent the equipment from starting unexpectedly.

3309407

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and

result in a fire or explosion and serious injury.

DGround the equipment and the object being dispensed to. Refer to Grounding on page 5.

DIf there is any static sparking or you feel an electric shock while using this equipment, stop dis-

pensing immediately. Do not use the equipment until you identify and correct the problem.

DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid

being dispensed.

DKeep the dispensing area free of debris, including solvent, rags, and gasoline.

DDo not smoke in the dispensing area.

DDo not turn on or off any light switch in the area while dispensing if fumes are present.

DNever use 1.1.1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents, or

fluids containing such solvents in pressurized aluminum equipment. Such use could result in a

chemical reaction, with the possibility of explosion.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,

inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,

state, and national guidelines.

DAlways wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and

solvent manufacturer.

DThe air motor exhausts any fluids added to the input air.

DGraco does not manufacture or supply the reactive chemical components that may be used in this

equipment and is not responsible for injury or property loss, damage, expense, or claims (direct or

consequential) that arise from the use of such chemical components.

4 309407

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

DThis equipment is for professional use only.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

DDo not alter or modify this equipment.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure stated on the equipment or in the Technical Data

for your equipment. Do not exceed the maximum working pressure of the lowest rated component

in your system.

DUse fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-

nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

DHandle hoses carefully. Do not pull on hoses to move equipment.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose

Graco hoses to temperatures above 66_C (150_F) or below –40_C (–40_F).

DWear hearing protection when operating this equipment.

DDo not move or lift pressurized equipment.

DComply with all applicable local, state, and national fire, electrical, and safety regulations.

5309407

Installation

NOTE: Reference numbers and letters in parentheses

in the text refer to the callouts in the figures and the

parts drawing.

NOTE: Always use Genuine Graco Parts and

Accessories, available from your Graco distributor.

Grounding

WARNING

FIRE AND EXPLOSION HAZARD

Before operating the pump, ground the

system as explained below. Also read

the section FIRE OR EXPLOSION HAZ-

ARD on page 3.

DPump: Use a ground wire and clamp as shown

below.

Fig. 1 TI1052

DAir and fluid hoses: Use only electrically conductive

hoses.

DAir compressor: Follow manufacturer’s

recommendations.

DDispensing valve: Ground through connection to a

properly grounded fluid hose and pump.

DObject being dispensed to: Follow your local code.

DSolvent pails used when flushing: Follow your local

code. Use only metal pails, which are conductive,

placed on a grounded surface. Do not place the pail

on a nonconductive surface, such as paper or

cardboard, which interrupts the grounding

continuity.

DTo maintain grounding continuity when flushing or

relieving pressure, hold a metal part of the

dispensing gun firmly to the side of a grounded

metal pail, then trigger the gun to ground the pump.

To ground the pump, remove the ground screw (Z)

and insert through the eye of the ring terminal at end of

ground wire (Y). Fasten the ground screw back onto

the pump and tighten securely. Connect the other end

of the ground wire to a true earth ground. See Fig. 1.

To order a ground wire and clamp, order Part No.

222011.

Mounting the Pump

WARNING

Mount the pump securely so that it cannot move

around during operation. Failure to do so could

result in personal injury or equipment damage.

DSelect a convenient location for the equipment to

ensure easy operator access to the pump air

controls, sufficient room to change supply

containers, and a secure mounting platform.

DIf you are mounting the pump directly on the supply

tank, position the pump so its intake valve is no

more than 1 in. (25 mm) from the bottom of the

container. Mount the pump to the cover or other

suitable mounting device.

6 309407

Installation

Mount the pump to suit the type of installation planned.

Very heavy lubricants may require an inductor plate.

See page 16 for the mounting hole layout and

dimensions

Install the air line accessories in the approximate order

shown in the Typical Installation. Install a bleed-type

master air valve (B) within easy reach of the pump,

upstream from the air regulator. Install an air filter (C)

to remove harmful dirt and moisture from your

compressed air supply. For automatic air motor

lubrication, install an air line oiler (D) close to the pump

air inlet. Install an air regulator (E) to control pump

speed.

WARNING

A bleed-type master air valve (B) is required to

shut off and relieve air pressure that may be

trapped in the air motor. Trapped air could cause

the pump to cycle unexpectedly and cause serious

bodily injury, including amputation.

Be sure the air hose is properly sized to deliver an

adequate supply of air to the motor. Refer to the

Technical Data on page 17.

Connect a dispensing hose to the 3/4 npt(f) pump

outlet. Install an appropriate gun or dispensing valve to

the hose.

Ground the pump as explained on page 5.

Fig. 2

Key

Grounded Air Line

Bleed-type Master Air Valve

Air Filter

Air Line Oiler

Air Regulator

Grounded Dispensing Hose

Elevator Assy. 241663

Ground Wire

Follow Plate 223701

Drum Cover 200326

Typical Installation

TI2371A

7309407

Operation

WARNING

DThis pump is designed to be used ONLY in

pumping non-corrosive and non-abrasive lubri-

cants and greases. Any other use of this pump

can cause unsafe operating conditions and

result in component rupture, fire, or explosion,

which can can cause serious bodily injury,

including injection.

DMoving parts can pinch or amputate your fin-

gers or other body parts. When the pump is

operating, the priming piston (located at the

pump intake) and the air motor piston (located

behind the air motor plates) move. NEVER

Operate the pump with the air motor plates

removed, and keep your fingers and hands

away from the priming piston.

Pressure Relief Procedure

WARNING

SKIN INJECTION HAZARD

Fluid under high pressure can be in-

jected through the skin and cause

serious injury. To reduce the risk of an

injury from injection, splashing fluid, or moving

parts, follow the Pressure Relief Procedure

whenever you

DAre instructed to relieve the pressure

DStop dispensing

DCheck or service any of the system equipment

DInstall or clean the dispensing nozzles

1. Close the air regulators.

2. Close the supply pump’s bleed-type master air

valve (required in this system).

3. Open the dispensing valve until pressure is fully

relieved.

If you suspect that the dispensing valve, extension, or

grease fitting coupler is clogged, or that pressure has

not been fully relieved after following the steps above,

VERY SLOWLY loosen the coupler or hose end

coupling and relieve pressure gradually, then loosen

completely, then clear the clog.

Startup and Adjustment

Open the bleed-type master air valve. Open the

dispensing valve, and slowly open the air regulator

until the pump is running smoothly. After all the air is

purged, close the dispensing valve. The pump will

start and stop as the valve is opened and closed.

CAUTION

Never allow the pump to run dry of the fluid being

pumped. A dry pump quickly accelerates to a high

speed and may damage itself. If your pump acceler-

ates quickly or is running too fast, stop it immediately

and check the fluid supply. If the supply container is

empty and air has been pumped into the lines, prime

the pump and lines with fluid, or flush the pump and

leave it filled with a compatible solvent. Be sure to

eliminate all air from the fluid system.

Use the air regulator (E) to control the pump speed

and fluid pressure. See Fig. 2. Always use the lowest

pressure necessary to obtain the desired results.

When you are finished using the pump for the day,

always follow the Pressure Relief Procedure at left.

Maintenance

The Accessory air line oiler (D) provides automatic air

motor lubrication. For daily manual lubrication,

disconnect the air hose, place about 15 drops of light

machine oil in the air inlet, reconnect the hose, and

turn on the air supply to blow oil into the motor.

8 309407

Troubleshooting

WARNING

To reduce the risk of serious injury whenever you

are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 7.

Before servicing this equipment always make sure to

Relieve the Pressure.

Note: Check all possible problems and solutions

before disassembling the pump.

Problem Cause Solution

Pump fails to operate. Inadequate air supply pressure or

restricted air lines

Increase air supply; clear

Closed or clogged valves Open; clean

Clogged fluid lines, hoses, valves,

etc.

Clear*

Damaged air motor Service air motor

Exhausted fluid supply Refill and reprime, or flush

Continuous air exhaust Worn or damaged air motor gasket,

packing, seal, etc.

Service air motor

Erratic pump operation Exhausted fluid supply Refill and reprime, or flush

ppp

Held open or worn intake valve or

piston packings

Clear; service

Pump operates, but output low on

upstroke

Held open or worn piston or packings Clear; service

Pump operates, but output low on

downstroke

Held open or worn intake valve Clear; service

Pump operates, but output low on

both strokes

Inadequate air supply or restricted air

lines

Increase air supply; clear

Closed or clogged valves Open; clean

Exhausted fluid supply Refill and reprime, or flush

Clogged fluid lines, hoses, valves,

etc.

Clear*

Loose packing nut or worn packings Tighten; replace

* Follow the Pressure Relief Procedure, and disconnect the fluid line. If the pump starts when the air is turned

back on, the fluid line, hose, valve, etc. was clogged.

9309407

Notes

10 309407

Service

TI2148A

Fig. 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco E-Flo Bedienungsanleitung

Graco

Graco ChemSafe 515 Stücklistenhandbuch

Graco

Graco Husky 1050 Series Gebrauchs- und Pflegehandbuch

Graco

Graco 239729 Bedienungsanleitung

Graco

Graco VPM Series Bedienungsanleitung

Graco

Graco Dura-Flo 2400 Bedienungsanleitung

Graco

Graco Pack'n Play Bedienungsanleitung

Graco

Graco SaniForce 24V310 Stücklistenhandbuch

Graco

Graco VISCOUNT II 210-107 Bedienungsanleitung

Graco

Graco Fireball 225 Bedienungsanleitung

Graco

Graco HYDRA-CAT FIXED RATIO Bedienungsanleitung

Graco

Graco Injecto-Flo II Single Line Bedienungsanleitung

Graco

Graco G-Mini Series Bedienungsanleitung

Graco

Graco 260550 Bedienungsanleitung

Graco

Graco Dyna-Star 236753 Bedienungsanleitung

Graco

Graco President Hydra-Clean 6880119 Stücklistenhandbuch

Graco

Graco Monark Bedienungsanleitung

Graco

Graco Fire-Ball 300 D Series Bedienungsanleitung

Graco

Graco ToughTek F340e Gebrauchs- und Pflegehandbuch

Graco

Graco ChemSafe 307 Stücklistenhandbuch

Graco

Graco 115 VAC EGP Bedienungsanleitung

Graco

Graco 24R968 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Metric CHECK-MATE 200 Datenblatt

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

GÜDE

GÜDE HWW 900 GC Bedienungsanleitung