Graco M680 Bedienungsanleitung

Instructions - Parts List

M680 Pump 332650A

Designed for spraying high viscosity materials, such as mortars, mastics, and epoxies.

For professional use only.

Model 262921

1000 psi (7 MPa, 70 bar) Maximum Working Pressure

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this

manual and all supplied manuals. Save all

instructions.

ti22250a

II 2 G

Related Manuals

2332650A

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Flush Before Using Equipment . . . . . . . . . . . . . . 6

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pressure Relief Procedure . . . . . . . . . . . . . . . . . 7

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Disconnect the Lower . . . . . . . . . . . . . . . . . . . . 10

Reconnect the Lower . . . . . . . . . . . . . . . . . . . . 10

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Pump Mounting Hole Diagram . . . . . . . . . . . . . . . 13

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

M680 Pump Performance Chart . . . . . . . . . . . . 15

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 16

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 16

Related Manuals

Component manuals in English. Manuals are available

at www.graco.com.

Manual Description

332649 680cc Pump Lower

312796 NXT Air Motor

Warnings

332650A 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific

hazard symbols and warnings not covered in this section may appear throughout the body of this manual where

applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes

are present.

• Ground all equipment in the work area. See Grounding instructions.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they

are antistatic or conductive.

•Stop operation immediately if static sparking occurs or you feel a shock.Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical

treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Warnings

4332650A

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-

ponent. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information

about your material, request MSDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure and disconnect all power sources.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

swallowed.

• Read MSDSs to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

SUCTION HAZARD

Powerful suction could cause serious injury.

• Never place hands near the pump fluid inlet when pump is operating or pressurized.

WARNING

Installation

332650A 5

Installation

Grounding

Pump: Use the ground screw (X) and lockwasher on the

motor to attach ground wire 262908 (Y). Tighten the

screw securely. Connect the other end of the ground

wire to a true earth ground.

Air and fluid hoses: use only electrically conductive

hoses. Check electrical resistance of hoses. If total

resistance to ground exceeds 29 megohms, replace

hose immediately.

Air compressor: follow manufacturer’s recommenda-

tions.

Applicator: ground through connection to a properly

grounded fluid hose and pump.

Fluid supply container: follow local code.

Object being sprayed: follow local code.

Solvent pails used when flushing: follow local code.

Use only conductive metal pails, placed on a grounded

surface. Do not place the pail on a nonconductive sur-

face, such as paper or cardboard, which interrupts

grounding continuity.

To maintain grounding continuity when flushing or

relieving pressure: hold metal part of the applicator

firmly to the side of a grounded metal pail, then trigger

the applicator.

Accessories

NOTE: Accessory Air Control Kits are available for the

NXT Air Motor. The kits include a master air valve, air

regulator, and filter. Order the kit separately. See manual

312796 for more information.

Air Line

•Bleed-type master air valve: required in your sys-

tem to relieve air trapped between it and the air

motor when the valve is closed.

Be sure the valve is easily accessible from the pump

and located downstream from the air regulator.

•Pump air regulator: to control pump speed and

outlet pressure. Locate it close to the pump.

•Air Motor Pilot Valve (Optional): to control air flow

to the air motor pilot valve to turn air motor on and

off.

•Air line filter: removes harmful dirt and moisture

from compressed air supply.

•Second bleed-type air valve: isolates air line

accessories for servicing. Locate upstream from all

other air line accessories.

•Applicator air regulator: controls air pressure to

the applicator.

The equipment must be grounded to reduce the risk

of static sparking. Static sparking can cause fumes to

ignite or explode. Improper grounding can cause

electric shock. Grounding provides an escape wire

for the electric current.

FIG. 1

TI8250a

Trapped air can cause the pump to cycle unexpectedly,

which could result in serious injury from splashing or

moving parts.

Installation

6332650A

Fluid Line

•Fluid drain valve: required in your system, to

relieve fluid pressure in the hose and applicator.

•Fluid shutoff valve: shuts off fluid flow.

•Fluid pressure regulator: for more precise adjust-

ment of the fluid pressure.

•Applicator or valve: to dispense fluid.

•Fluid line swivel: for easier applicator movement.

•Suction kit: enables the pump to draw fluid from a

container.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is

left in the fluid passages to protect parts. To avoid con-

taminating your fluid with oil, flush the equipment with a

compatible solvent before using the equipment. See

Flushing, page 8.

NOTICE

To prevent material hardening in the fluid drain

valve, flush the fluid drain valve after every time it is

used. See Flushing on page 8.

Operation

332650A 7

Operation

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever

you see this symbol.

1. If you are pumping fluid which dries, hardens, or

sets up, flush the system. See Flushing.

2. Engage applicator trigger lock, if equipped.

3. Close the bleed-type master air valve.

4. Disengage applicator trigger lock, if equipped.

5. Hold a metal part of the applicator firmly to a

grounded metal pail. Trigger the applicator to relieve

pressure.

6. Engage applicator trigger lock, if equipped.

7. Open all fluid drain valves in the system, having a

waste container ready to catch drainage. Leave

drain valve(s) open until you are ready to spray

again.

8. If you suspect the spray tip or hose is clogged or

that pressure has not been fully relieved after follow-

ing the steps above, VERY SLOWLY loosen

threaded fitting to relieve pressure gradually, then

loosen completely. Clear hose or tip obstruction.

9. Flush the fluid drain valve if it was used.

Shutdown

1. Stop the pump at the bottom of its stroke.

NOTE: This prevents fluid from drying on the rod and

damaging the throat packings.

2. If pumping fluid which dries, hardens, or sets up,

flush the system. See Flushing.

3. Perform Pressure Relief Procedure, page 7.

4. If pumping mortar or similar materials:

a. Disconnect the Lower, page 10.

b. Disassemble and clean lower with a brush and

solvent. See lower manual 332649.

c. Assemble lower.

d. Reconnect the Lower, page 10.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before

cleaning, checking, or servicing the equipment.

NOTICE

To prevent material hardening in the fluid drain

valve, flush the fluid drain valve after every time it is

used. See Flushing on page 8.

NOTICE

Never leave water or water-based fluid in pump

overnight. If you are pumping water-based fluid,

flush with water first, then with a rust inhibitor, such

as mineral spirits solvent (also called white spirit).

Relieve pressure, but leave rust inhibitor in pump to

protect parts from corrosion.

Maintenance

8332650A

Flushing

If you are pumping fluid which dries, hardens, or sets up,

flush the system with a compatible solvent as often as

necessary to prevent build up of dried fluid in the pump

or hoses.

1. Perform Pressure Relief Procedure, page 7.

2. Remove the spray tip.

3. Hold a metal part of the applicator firmly to the side

of a grounded metal pail.

4. Start the pump.

5. If pumping mortar or similar materials:

a. Circulate flushing fluid at 60-90 cycles per min-

ute for 3-5 minutes.

b. Perform Pressure Relief Procedure, page 7.

c. Drain flushing fluid then refill with clean flushing

fluid.

d. Circulate flushing fluid at 60-90 cycles per min-

ute for a 3-5 minutes.

e. Perform Pressure Relief Procedure, page 7.

f. Drain flushing fluid.

6. If not pumping mortar:

a. Use the lowest possible fluid pressure during

flushing.

b. When flushing is complete, perform Pressure

Relief Procedure, page 7.

Maintenance

Lubrication

The accessory air line lubricator provides automatic air

motor lubrication. For daily, manual lubrication, relieve

the pressure, disconnect the regulator, place about 15

drops of light machine oil in the pump air inlet, reconnect

the regulator, and turn on the air supply to blow oil into

the motor.

Verify pump lower packing nut is 1/2 full with Throat Seal

Liquid (TSL).

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before

cleaning, checking, or servicing the equipment.

ti21631a

Troubleshooting

332650A 9

Troubleshooting

1. Relieve the pressure.

2. Check all possible problems and solutions before

disassembling pump.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before

cleaning, checking, or servicing the equipment. Never operate the pump with the air motor spring

guard removed. Moving parts can pinch or amputate

your fingers or other body parts.

PROBLEM CAUSE SOLUTION

Pump does not operate, or no fluid

flow.

Restricted line or inadequate air

supply.

Clear, increase.

Exhausted fluid supply. Refill and prime.

Clogged fluid hoses. Clean, or replace.

Damaged air motor. Repair.

Loose or broken pump parts. Disassemble, check, repair.

Pump operates, but output is low. Insufficient air supply. Increase. See M680 Pump Perfor-

mance Chart on page 15 for

required air pressure and flow for

desired pump output.

Exhausted fluid supply. Refill and prime.

Obstructed applicator or dispensing

valve.

Clear.

Packing retainer needs adjustment. Loosen or tighten screws as neces-

sary.

Damaged fluid pump packings. Replace.

Held open or worn piston intake

valve.

Repair.

Erratic or accelerated operation. Exhausted fluid supply. Refill and prime.

Fluid intake or piston valve worn. Repair.

Repair

10 332650A

Repair

Disconnect the Lower

1. Flush the pump. Perform Flushing, page 8.

2. Perform Pressure Relief Procedure, page 7.

3. With fluid pressure relieved, remove fluid inlet and

outlet connections from pump lower.

4. Disconnect pump rod (see FIG. 2):

a. Push piston rod protective spring up and away

from coupling assembly.

b. Remove clip (A), and slide coupling cover (B) up

to remove coupling (C).

5. Hold the tie rod flats with a wrench to keep the rods

(2) from turning. Unscrew the nuts (4). Remove the

lower (3). See Parts on page 11.

6. To service the lower, refer to lower manual 332649,

supplied. To service the air motor, refer to air motor

manual 312796, supplied.

Reconnect the Lower

1. Make sure the spring guard is in place over the air

motor shaft.

2. Use at least two people to hold the lower while

another reconnects it to the motor. Place the lower

(2) on the tie rods (6) then screw the nuts (4) onto

the tie rods (2). Torque to 50-60 ft-lb.

3. Install coupling (C), slide coupling cover (B) over

coupling, then install clip (A) to secure pump rod to

air motor rod.

4. Reconnect all hoses.

5. Reconnect the ground wire if it was disconnected.

6. Fill the wet-cup 1/2 full of Graco Throat Seal Liquid

(TSL).

7. Turn on the air power supply. Run the pump slowly

to ensure that it operates properly.

NOTICE

To prevent dropping the system and damaging it,

use at least two people when lifting, moving, or dis-

connecting the pump. If disconnecting the lower, be

sure to securely brace the pump, or have two peo-

ple hold it while another disconnects it.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before

cleaning, checking, or servicing the equipment.

FIG. 2

ti21656a

Andere Handbücher für M680

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Dura-Flo 600 Stücklistenhandbuch

Graco

Graco Fire-Ball H Series Bedienungsanleitung

Graco

Graco Husky 715 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Power-Flo Series Bedienungsanleitung

Graco

Graco 253377 Bedienungsanleitung

Graco

Graco G Series Bedienungsanleitung

Graco

Graco E-Flo DC 333389E Stücklistenhandbuch

Graco

Graco 218746 Bedienungsanleitung

Graco

Graco Dura-Flo 1200 Bedienungsanleitung

Graco

Graco Dyna-Star 200:1 Bedienungsanleitung

Graco

Graco Therm-O-Flow C03508 Stücklistenhandbuch

Graco

Graco Metric CHECK-MATE 200 Datenblatt

Graco

Graco Dyna-Star 3A6941J Bedienungsanleitung

Graco

Graco GH 733 HYDRA-SPRAY Bedienungsanleitung

Graco

Graco 248061 Bedienungsanleitung

Graco

Graco Monark A Series Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco FIRE-BALL Series Stücklistenhandbuch

Graco

Graco Dyna-Star HP 77X202 Bedienungsanleitung

Graco

Graco Fire-Ball B Series Bedienungsanleitung

Graco

Graco 258906 Montageanleitung

Graco

Graco Check-Mate 800 Series Bedienungsanleitung

Graco

Graco Dura-Flo 1100 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung