Greenlee ES25 Bedienungsanleitung

INSTRUCTION MANUAL

ES25

Battery-powered ACSR Cutter

22131—with 120V Charger

22132—with 220V Charger

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Description

The Greenlee ES25 Battery-powered Cutter is intended

to cut up to 636 kcmil Grosbeak ACSR cable.

The cable cutter is driven by a 14.4 V motor and is

battery. The motor is protected by a circuit breaker.

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee tools:

ES25-11 Battery-powered ACSR Cutter, 120 V

ES25-22 Battery-powered ACSR Cutter, 220 V

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

All specications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Important Safety Information .....................................3–5

Identication.................................................................. 6

Specications................................................................ 6

Operation....................................................................... 7

Maintenance.................................................................. 8

Troubleshooting............................................................. 9

Illustration and Parts List........................................10–11

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning could

result in severe injury or death.

Note: Keep all decals clean and legible, and replace

when necessary.

Cable Cutter

Electric shock hazard:

This tool is not insulated. When using

this unit near energized electrical

lines, use proper personal protective

equipment.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Keeps hands away from blade.

Remove the battery before

inspecting or servicing the tool.

Failure to observe these warnings

could result in severe injury or death.

•

Use this tool for manufacturer’s intended use only.

Use other than that which is described in this

manual can result in injury or property damage.

Do not cut guy wire or steel rod.

Do not exceed the rated capacity of the tool.

Inspect the tool before each use. Replace any worn,

damaged, or missing items with Greenlee replace-

ment parts. A damaged or improperly assembled

tool can break and strike nearby personnel.

Failure to observe these precautions may result in

injury or property damage.

•

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

Battery

Do not dispose of battery in a re. The battery will

vent harmful vapors and can explode.

Failure to observe this warning could result in severe

injury or death.

Do not allow any object to contact the battery

terminals.

Do not immerse batteries in liquid. Liquid may

create a short circuit and damage the battery.

Do not place the battery into a pocket, tool pouch,

or tool box with conductive objects. Conductive

objects may create a short circuit and damage the

battery.

Do not place a battery on moist ground or grass.

Moisture may create a short circuit and damage the

battery.

Failure to observe these precautions may result in

injury or property damage.

•

Do not charge the battery if it is cooler than 50 °F

(10 °C) or warmer than 95 °F (35 °C). Damage to the

battery can result.

Do not store the battery at more than 140 °F

(60 °C). Damage to the battery can result.

Do not use another manufacturer’s charger. Other

manufacturers’ chargers may overcharge and

damage the battery.

Failure to observe these precautions may result in

injury or property damage.

•

Do not expose the battery to liquids such as water,

oil, or solvents. Liquids will damage the battery.

Do not attempt to open the battery. It contains no

user-serviceable parts.

Use this battery for manufacturer’s intended use

only. Use other than that which is described in this

manual can result in injury or property damage.

Inspect the battery before each use. Do not use a

damaged battery.

Failure to observe these precautions may result in

injury or property damage.

•

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

Charger

Electric shock hazard:

Use indoors only.

Do not expose the charger to rain,

snow, or wet conditions.

Unplug the charger from the power

source before cleaning the charger.

Failure to observe these warnings

could result in severe injury or death.

•

Greenlee recommends plugging the charger directly

into a receptacle. If an extension cord must be used:

Select an extension cord with a conguration that

exactly matches that of the charger’s plug.

Inspect the extension cord for wear or damage.

Use of an improper or damaged extension cord could

result in electric shock or re.

•

Do not obstruct the ventilation slots. This device

generates heat while charging. Excessive internal

heat can result in a re.

Do not use or store the charger near a heat

source. This device generates heat while charging.

Excessive internal heat can result in a re.

Failure to observe these warnings could result in

severe injury or death.

•

Use this charger to charge the supplied 14.4 V

rechargeable NiCd (nickel cadmium) batteries only.

Other batteries may burst if charged with this charger.

Failure to observe this warning could result in severe

injury or death.

Do not place anything other than the supplied 14.4 V

rechargeable NiCd (nickel cadmium) battery into the

battery pocket.

Keep dirt and foreign objects out of the battery

pocket.

Do not create a short circuit across the contacts in

the battery pocket.

Failure to observe this precaution may result in injury

or property damage.

•

Do not connect the charger to a generator. Voltage

uctuations can damage the charger.

Inspect the charger before each use. Replace the

unit if either the charger or cord show signs of

damage or wear.

Do not attempt to repair the charger. It contains no

user-serviceable parts.

Use this tool for manufacturer’s intended use only.

Use other than that which is described in this

manual can result in injury or property damage.

Failure to observe these precautions may result in

injury or property damage.

•

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Identiﬁcation

Speciﬁcations

Cable Cutter

Weight (with battery) ............................................................................3.5 kg (7.7 lb)

Motor.......................................................................................................... 14.4 VDC

Capacity

ACSR ..............................................................................636 kcmil (except Egret)

Aluminum............................................................................................. 1500 kcmil

Battery

Type...........................................................................Rechargeable nickel-cadmium

Voltage ............................................................................................................ 14.4 V

Charger

Voltage ..................................................................................... 120 VAC or 220 VAC

1. Movable blade

2. Stationary blade

3. Driver

4. Forward/reverse

switch

5. Trigger

6. Reset button

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Operation

Electric shock hazard:

This tool is not insulated. When using

this unit near energized electrical

lines, use proper personal protective

equipment.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Do not cut steel.

Failure to observe this precaution may result in injury

or property damage.

1. Activate the switch to open the movable blade.

2. Place the cable to be cut onto the stationary blade

and close the movable blade around the cable.

Feed the movable blade by hand so that the gear

teeth engage the drive mechanism of the tool.

3. Slide the direction control lever to FORWARD.

Press and hold the trigger switch until the cable is

completely cut.

4. Slide the direction control lever to the center (LOCK)

position.

5. When nished, remove any dust or particles that

may have become attached to the brush.

Circuit Breaker

The following may cause the circuit breaker to trip:

Cutting material that is too large

Cutting material that is too hard

Overheating due to continuous use

Drawing excessive current

If the circuit breaker trips, the tool will stop. If necessary,

allow the tool to cool down. Press the RESET button.

(Wait 10 seconds to one minute before resetting.)

•

Removing the Battery

Do not dispose of battery in a re. The battery will

vent harmful vapors and can explode.

Failure to observe this warning could result in severe

injury or death.

1. Press the battery latch on the battery.

2. Pull the battery down and out of the tool.

Charging the Battery

Do not connect the charger to a generator. Voltage

uctuations can damage the charger.

Failure to observe this precaution may result in injury

or property damage.

The battery charger will recharge the battery in approxi-

mately one hour.

1. Set the charger on a rm level surface out of direct

sunlight. Be sure that the charger’s ventilation slots

are not blocked.

2. Connect the charger to an appropriate power

supply.

3. Insert the battery into the battery pocket of the

charger. The red LED will light to indicate that the

battery is charging. The red LED turns off and the

green LED turns on when the battery is at 80%

capacity. To reach 100% capacity will take approxi-

mately 13 to 15 hours after the green LED switches

on.

Note: It is acceptable to use the battery after the

red LED turns off and the green LED turns on.

4. Remove the battery from the charger.

Note: Allow the charger to cool for at least 15 minutes

before charging another battery.

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Maintenance

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Keeps hands away from blade.

Remove the battery before

inspecting or servicing the tool.

Failure to observe these warnings

could result in severe injury or death.

•

Daily Maintenance

Store the tool in a cool, dry area to prevent rust.

Inspect the blades for damage or burrs. Remove burrs

on the back side of the blades with a at grinding

stone.

Clean the plastic housing with a soft, soaped cloth.

•

Replacing the Gear Guides

1. This tool has two gear guides — left and right.

Operate the cutter in either the forward or reverse

direction to move the blade completely out of the

gear mechanism.

2. Remove the battery from the cutter.

3. Use an M2.5 Allen wrench to loosen and remove

the screw that secures the gear guide and install the

replacement guides on the movable blade.

4. Tighten the screw securely.

5. Re-install the battery and operate the cutter.

Replacing the Movable Blade

1. Operate the cutter in either the forward or reverse

direction until the movable blade is clear of the

pinion gear.

2. Remote the battery from the cutter.

3. Secure the lock nut with a wrench, and then loosen

the shoulder screw with a screwdriver.

4. Remove the movable blade from the tool. Be sure

not to lose the two curved washers.

5. Use an M2.5 Allen wrench to loosen and remove

the two screws that secure the left and right orange

gear guides to the movable blade.

6. Install the left and right gear guides on the new

movable blade. Put the right gear guide on the right

side of the blade and the left gear guide on the

left side of the blade and tighten securely. A lock

washer is located between the screw head and the

gear guide.

7. Install the new movable blade by reassembling the

shoulder screw and lock nut.

8. Re-install the battery and operate the cutter.

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Troubleshooting

Problem Probable Cause Probable Remedy

Cutter does not operate. Battery is discharged. Charge battery.

Internal circuit breaker has tripped. Reset circuit breaker.

Movable blade is not completely

engaged.

Push movable blade until it is

completely engaged with drive.

Dust or foreign matter lodged at

battery contacts.

Clean battery contacts.

Charging LED does not illuminate. Battery contacts are dirty. Clean battery contacts on battery

and in battery charger.

Battery cartridge is too warm. Allow battery to cool.

Battery life has

decreased.

Battery will not hold a charge. Replace battery.

Blades are dull. Replace blades.

ES25 Battery-powered ACSR Cutter

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Illustration

Inhaltsverzeichnis

Andere Greenlee Cutter Handbücher

Greenlee

Greenlee ESG65LXR Bedienungsanleitung

Greenlee

Greenlee GATOR ESG105LXR Bedienungsanleitung

Greenlee

Greenlee GATOR EK425LXCJACSR Bedienungsanleitung

Greenlee

Greenlee ESC85 Bedienungsanleitung

Greenlee

Greenlee 758 Bedienungsanleitung

Greenlee

Greenlee ES85 Bedienungsanleitung

Greenlee

Greenlee GATOR Plus ESG45GL Bedienungsanleitung

Greenlee

Greenlee GATOR ESG85GL Bedienungsanleitung

Greenlee

Greenlee GATOR ESR1000LX Bedienungsanleitung

Greenlee

Greenlee ES32FML Bedienungsanleitung

Greenlee

Greenlee 764 Leitfaden

Greenlee

Greenlee 773 Bedienungsanleitung

Greenlee

Greenlee ESG65LXR11 Bedienungsanleitung

Greenlee

Greenlee GATOR ESG55LX Bedienungsanleitung

Greenlee

Greenlee GATOR CSG45GL Bedienungsanleitung

Greenlee

Greenlee GATOR ESG45L Bedienungsanleitung

Greenlee

Greenlee 881 Cam Track Bedienungsanleitung

Greenlee

Greenlee C3 Auto Whip Clad Cable Cutter Bedienungsanleitung

Greenlee

Greenlee GATOR ETS12 Bedienungsanleitung

Greenlee

Greenlee 763 Bedienungsanleitung

Greenlee

Greenlee ES20LXR Bedienungsanleitung

Greenlee

Greenlee SDG45 Bedienungsanleitung

Greenlee

Greenlee Shear 30T Bedienungsanleitung

Greenlee

Greenlee KP1022 INS Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung