Greenlee ES750 Bedienungsanleitung

INSTRUCTION MANUAL

Read and understand all of the instructions

and safety information in this manual before

operating or servicing this tool.

ES750

Battery-powered Cable Cutter

45380—with 120 V Charger

45381—with 220 V Charger

KEEP THIS MANUAL

Table of Contents

Description, Safety, and Purpose of this Manual .............................................................. 2

Important Safety Information .......................................................................................... 3–8

Specifications ..................................................................................................................... 9

Operation .......................................................................................................................... 10

Charger ............................................................................................................................. 11

Troubleshooting ................................................................................................................ 12

Maintenance ..................................................................................................................... 13

Illustration ......................................................................................................................... 14

Parts List ..................................................................................................................... 15–16

Description

The Greenlee Battery-powered Cable Cutter is intended to cut up to 750 Kcmil copper

and aluminum cable. The cable cutter is driven by a 12-volt motor and is powered by a

rechargeable NiCd (nickel cadmium) battery. The motor is protected by a circuit breaker.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment.

This manual and any markings on the tool provide information for avoiding hazards and

unsafe practices related to the use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with the safe operation and

maintenance procedures for the Greenlee ES750 Battery-powered Cable Cutter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

All specifications are nominal and may change as design improvements occur.

Greenlee Textron Inc. shall not be liable for damages resulting from misapplication

or misuse of its products.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

ES750

IMPORTANT SAFETY INFORMATION

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury

or death.

Hazards which, if not avoided, COULD result in severe injury or

death.

Hazards or unsafe practices which, if not avoided, MAY result in

injury or property damage.

Read and understand all of the instructions and safety informa-

tion in this manual before operating or servicing this tool.

Failure to observe this warning could result in severe injury or

death.

This symbol is used to call your attention to hazards or unsafe practices which

could result in an injury or property damage. The signal word, defined below,

indicates the severity of the hazard. The message after the signal word provides

information for preventing or avoiding the hazard.

IMPORTANT SAFETY INFORMATION

Cable Cutter

• Use this tool for manufacturer’s intended use only. Use other than that which is

described in this manual can result in injury or property damage.

• Do not cut steel or ACSR.

• Inspect the tool before each use. Replace any worn, damaged, or missing

items with Greenlee replacement parts. A damaged or improperly assembled

tool can break and strike nearby personnel.

Failure to observe these precautions may result in injury or property damage.

• Keeps hands away from blade.

• Remove the battery before inspecting or servicing the tool.

Failure to observe these warnings could result in severe

injury or death.

Wear eye protection when operating or servicing this tool.

Failure to wear eye protection could result in serious eye

injury from flying debris.

Electric shock hazard:

This tool is not insulated. When using this unit near

energized electrical lines, use proper personal protective

equipment.

Failure to observe this warning could result in severe injury or

death.

ES750

Battery

IMPORTANT SAFETY INFORMATION

• Do not charge the battery if it is cooler than 50 °F (10 °C) or warmer than

95 °F (35 °C). Damage to the battery can result.

• Do not store the battery at more than 140 °F (60 °C). Damage to the battery

can result.

• Do not use another manufacturer’s charger. Other manufacturers’ chargers

may overcharge and damage the battery.

Failure to observe these precautions may result in injury or property damage.

Do not allow any object to contact the battery terminals.

• Do not immerse batteries in liquid. Liquid may create a short circuit and

damage the battery.

• Do not place the battery into a pocket, tool pouch, or tool box with conductive

objects. Conductive objects may create a short circuit and damage the

battery.

• Do not place a battery on moist ground or grass. Moisture may create a short

circuit and damage the battery.

Failure to observe these precautions may result in injury or property damage.

Do not dispose of battery in a fire. The battery will vent harmful vapors and

can explode.

Failure to observe this warning could result in severe injury or death.

Battery (cont’d)

IMPORTANT SAFETY INFORMATION

• Do not expose the battery to liquids such as water, oil, or solvents. Liquids

will damage the battery.

• Do not attempt to open the battery. It contains no user-serviceable parts.

• Use this battery for manufacturer’s intended use only. Use other than that

which is described in this manual can result in injury or property damage.

• Inspect the battery before each use. Do not use a damaged battery.

Failure to observe these precautions may result in injury or property damage.

ES750

Charger

IMPORTANT SAFETY INFORMATION

• Do not obstruct the ventilation slots. This device generates heat while

charging. Excessive internal heat can result in a fire.

• Do not use or store the charger near a heat source. This device generates

heat while charging. Excessive internal heat can result in a fire.

Failure to observe these warnings could result in severe injury or death.

Greenlee recommends plugging the charger directly into a receptacle. If an

extension cord must be used:

• Select an extension cord with a configuration that exactly matches that of the

charger’s plug.

• Inspect the extension cord for wear or damage.

Use of an improper or damaged extension cord could result in electric shock or fire.

Electric shock hazard:

• Use indoors only.

• Do not expose the charger to rain, snow, or wet conditions.

• Unplug the charger from the power source before cleaning

the charger.

Failure to observe these warnings could result in severe

injury or death.

IMPORTANT SAFETY INFORMATION

Charger (cont’d)

• Do not connect the charger to a generator. Voltage fluctuations can damage

the charger.

• Inspect the charger before each use. Replace the unit if either the charger or

cord show signs of damage or wear.

• Do not attempt to repair the charger. It contains no user-serviceable parts.

• Use this tool for manufacturer’s intended use only. Use other than that which

is described in this manual can result in injury or property damage.

Failure to observe these precautions may result in injury or property damage.

Do not place anything other than the supplied 12-volt rechargeable NiCd (nickel

cadmium) battery into the battery pocket.

• Keep dirt and foreign objects out of the battery pocket.

• Do not create a short circuit across the contacts in the battery pocket.

Failure to observe this precaution may result in injury or property damage.

Use this charger to charge the supplied 12-volt rechargeable NiCd (nickel

cadmium) batteries only. Other batteries may burst if charged with this charger.

Failure to observe this warning could result in severe injury or death.

ES750

Specifications

Cutter

Weight (with battery) ......................................................................................... 5 lb, 8 oz

Weight (with battery, charger, and case) ........................................................ 9 lb, 10 oz

Height ................................................................................................................... 13-5/8"

Width ....................................................................................................................... 6-1/2"

Depth ...................................................................................................................... 4-1/8"

Wire Type ........................................................................................Copper or aluminum

Maximum Wire Size ......................................................................................... 750 Kcmil

Motor .................................................................................................................... 12 VDC

Battery

Type ................................................................................ Rechargeable nickel-cadmium

Voltage...................................................................................................................... 12 V

Charger

Voltage........................................................................................... 120 VAC or 220 VAC

Trigger

RESET

(yellow button)

Operation

1. Slide the direction control lever to select either FORWARD or REVERSE. Press the

switch to activate the cable cutter. Release the switch after the movable blade is

disengaged from the driver.

2. Place the cable to be cut against the stationary blade until it is engaged by the driver.

Close the movable blade around the cable.

3. Slide the direction control lever to FORWARD. Press the switch. After the cable is

completely cut, release the switch.

4. Slide the direction control lever to the center (LOCK) position.

Circuit Breaker

The following may cause the circuit breaker to trip:

• Cutting material that is too large

• Cutting material that is too hard

• Overheating due to continuous use

• Drawing excessive current

If the circuit breaker trips, the tool will stop. If necessary, allow the tool to cool down.

Press the RESET button. (Wait 10 seconds to 1 minute before resetting.)

REVERSE

Driver

Fixed Blade

Movable Blade

FORWARD

LOCK

Do not cut steel or ACSR.

Andere Handbücher für ES750

Inhaltsverzeichnis

Andere Greenlee Cutter Handbücher

Greenlee

Greenlee 750 Bedienungsanleitung

Greenlee

Greenlee SDG45 Bedienungsanleitung

Greenlee

Greenlee GATOR ESG55LX Bedienungsanleitung

Greenlee

Greenlee EBS12ML Bedienungsanleitung

Greenlee

Greenlee 881 Cam Track Bedienungsanleitung

Greenlee

Greenlee ESG65LXR11 Bedienungsanleitung

Greenlee

Greenlee GATOR EK425LXCJACSR Bedienungsanleitung

Greenlee

Greenlee 645-3/4 Bedienungsanleitung

Greenlee

Greenlee GATOR ESG50GL Bedienungsanleitung

Greenlee

Greenlee GATOR Plus ESG50GL Bedienungsanleitung

Greenlee

Greenlee GATOR ESR1000LX Bedienungsanleitung

Greenlee

Greenlee ES25 Bedienungsanleitung

Greenlee

Greenlee 758 Bedienungsanleitung

Greenlee

Greenlee GATOR Plus ESG45GL Bedienungsanleitung

Greenlee

Greenlee GATOR ES1000 Bedienungsanleitung

Greenlee

Greenlee 764 Leitfaden

Greenlee

Greenlee GATOR ESG45GL Bedienungsanleitung

Greenlee

Greenlee ES20LXR Bedienungsanleitung

Greenlee

Greenlee Gator ES20HVX Bedienungsanleitung

Greenlee

Greenlee GATOR ETS12 Bedienungsanleitung

Greenlee

Greenlee GATOR ESG45L Bedienungsanleitung

Greenlee

Greenlee 645-11/16 Bedienungsanleitung

Greenlee

Greenlee ESG65LXR Bedienungsanleitung

Greenlee

Greenlee ES750 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung