Grizzly H7197 Bedienungsanleitung

MODEL H7197 ZERO-CLEARANCE/DADO TABLE SAW

INSERT INSTRUCTIONS

WARNINGS

• Disconnect the saw from its power source before fitting or removing the insert.

• Always wear eye protection.

• Be sure the blade is NOT in contact with the insert before switching the saw ON.

• Do not attempt to tilt the arbor while the blade is in the insert! The blade will bind, causing severe damage

and possible injury! For beveled cuts, a separate, dedicated insert must be prepared. To do this, preset

the angle and then proceed as instructed below.

• The insert must be securely clamped down with a board before plunging the blade up to cut the kerf.

• If you are using blade stabilizers, check their clearance before raising the blade.

INSTALLING AND FITTING YOUR INSERT

1) Lower the blade completely.

2) Place the insert in the throat opening, back end first, with the starter pocket located over the blade.

Initially, the insert should be too long and hit on the front “fitting bumps.”

3) Using a medium grit sanding block, LIGHTLY sand all four fitting bumps. Also, lightly bevel the bottom

edges of the FRONT bumps to ease entry. Sand, test, repeat—to gradually “sneak-up” on a snug, yet

easily removable fit. Once you have achieved a tight wedge fit, work on only the front bumps from then

on.

4) Using a 3⁄32" hex wrench, adjust the leveling screws until the insert is stable and flush with the tabletop.

5) SPLITTER: If the insert is to be used with a splitter, you will need to finish cutting out the pre-routed

optional splitter slot, using a saw or router and then rounding the sharp edges with sandpaper.

CUTTING THE BLADE SLOT (KERF)

1) Check that the insert is fitted properly and that the blade is clear of the bottom of the insert. Using a stick,

reach under the table and rotate the blade manually to check for blade clearance.

2) Fully cover the insert with a board, and clamp it to the table saw top at each end.

3) Reconnect power to the saw. Switch the saw ON, slowly and cautiously raise blade up to cut through

the insert. WARNING—KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR EYE

PROTECTION. Make sure you raise the blade to the maximum height at this time.

4) Lower the blade, turn off the saw, and remove the board. Your insert is now ready for use!

IMPORTANT TIPS

• Only use this insert with carbide tipped blades.

• DADO BLADE: Use the same procedures outlined above, but use additional caution due to the excessive

material being machined from the insert during the slotting procedure.

• Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type

blades, excessive arbor run-out, or blade distortion may be causing intermittent contact with the insert

slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.

• Ideally, a separate insert should be used with each blade, dado stack, or angle setup. This will ensure a

true “zero-clearance” effect and give you the maximum benefit from your inserts.

#6766BL

Inhaltsverzeichnis

Andere Grizzly Zubehör Handbücher

Grizzly

Grizzly G0577 Bedienungsanleitung

Grizzly

Grizzly H8165 Bedienungsanleitung

Grizzly

Grizzly G1822 Bedienungsanleitung

Grizzly

Grizzly G1763 Bedienungsanleitung

Grizzly

Grizzly G0708 Bedienungsanleitung

Grizzly

Grizzly G8987 Bedienungsanleitung

Grizzly

Grizzly POWER FEED H8370 Bedienungsanleitung

Grizzly

Grizzly T10667 Bedienungsanleitung

Grizzly

Grizzly G7873 Kurzanleitung

Grizzly

Grizzly T10113 Bedienungsanleitung

Grizzly

Grizzly H8165 Bedienungsanleitung

Grizzly

Grizzly D3080 Bedienungsanleitung

Grizzly

Grizzly G7028 Bedienungsanleitung

Grizzly

Grizzly G4816 Bedienungsanleitung

Grizzly

Grizzly G1026 Bedienungsanleitung

Grizzly

Grizzly H0775 Bedienungsanleitung

Grizzly

Grizzly H8369 Bedienungsanleitung

Grizzly

Grizzly T20682 Bedienungsanleitung

Grizzly

Grizzly G1705 Bedienungsanleitung

Grizzly

Grizzly H8068 Bedienungsanleitung

Grizzly

Grizzly H8174 Bedienungsanleitung

Grizzly

Grizzly G0750G Bedienungsanleitung

Grizzly

Grizzly G5960 Bedienungsanleitung

Grizzly

Grizzly g5749 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung