Grundfos Unilift KP 250 Gebrauchsanweisung

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333 [email protected]

12

Technical data

Unilift KP

Fig. 7 Unilift KP-S

Unilift KP is a single-stage, submersible, stainless steel

drainage pump in compact design with hermetically

sealed stator housing (wet runner).

The pump can be installed in a permanent installation or

used as a portable pump. It may be operated fully or

partially submerged.

The pump is suitable for:

• pumping in drain pits

• pumping of wastewater without discharge from

toilets

• drainage of flooded cellars or buildings

• emptying of swimming pools, tanks and fountains

• applications within agriculture, horticulture, dairies,

breweries and the process industry.

Versions

The Unilift KP pump series comes in these versions:

• KP-S with integrated, electronic sensor

(automatic operation)

• KP-A with float switch (automatic operation)

• KP-M without level switch (manual operation).

It is possible to upgrade a Unilift KP-A and a Unilift KP-M,

220-240 V, 50 Hz, to a Unilift KP-S. Contact Grundfos.

Special features of Unilift KP-S

• Compact design - requires a minimum of space

• Automatically self-venting if air is trapped in impeller

• Protected against blocked impeller and dry-running

• Integrated, nanocoded, super-slip, electronic sensor

• Starts even with a 2 mm thick layer of dirt on the

sensor plate.

Approvals

CE, LGA, VDE, GS, EMV, GOST, UL, CSA and

C-TICK.

Pumped liquids

The pump is suitable for

• clean, non-aggressive water

• slightly dirty (grey) wastewater.

The open-impeller construction ensures the free passage

of solids up to ø10 mm.

Functions

Unilift KP-S

Automatic start/stop operation by means of a sensor.

The pump starts:

• when the liquid level reaches the sensor plate

• when the pump is connected to the electricity supply

• when the sensor plate is touched with a finger.

The pump stops:

• when the pump starts to suck air (automatic stop)

• if the impeller is blocked.

Unilift KP-A

Automatic start/stop operation by means of a float switch.

Unilift KP-M

Manual operation by means of external start/stop.

Construction

The stainless steel pump sleeve is made in one piece with

Rp 1¼ discharge port and insulating handle. Mains cable

andfloatswitchcablearecombined in one vulcanizedand

water-tight plug, secured to the socket of the hermetically

sealed stator housing.

Liquid enters the pump through the holes of the suction

strainer. The holes of the strainer prevent the passage of

large solids.

The sturdy impeller has single-curved vanes. The

bevelled front edges prevent fibres from jamming the

impeller.

The guide vanes of the pump housing guide the liquid,

lifting sand grains into the liquid flow. This prevents sand

from blocking the impeller.

Motor

The motor is a single- or three-phase, asynchronous

canned motor with liquid-filled rotor chamber and water-

lubricated bearings. The motor is cooled by the pumped

liquid around the motor.

Enclosure class: IP 68

Insulation class: F.

The motor incorporates automatic overload protection. In

case of overload, the motor stops automatically. When

cooled, the motor restarts automatically.

GrA2568

Drainage pumps

Unilift KP

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333 [email protected]

13

Technical data

Selection

The below overview is suitable for the selection of the correct size of Unilift KP pumps used in stationary applications.

The flow velocity through the discharge pipe must be minimum 0.7 m/s to ensure self-cleaning.

Example: ADN 32discharge pipe withan inner diameter of 26 to 34 mm (depending on local standards)requires aminimum

flow velocity of approximately 2.3 m3/h.

The overview below shows the maximum lengths of combined vertical and horizontal DN 32 discharge pipes.

Fig. 8 Overview of maximum lengths of combined vertical and horizontal discharge pipes

The above overview is only intended as a guide. Grundfos is not liable for any faulty installations based on the overview.

Note: If the non-return valve is used, the pressure drop in the valve is 0.2 m head. The pressure drop is to be subtracted

from the vertical pipe lengths.

The vertical height of the discharge pipe should be measured from the pump stop level.

TM03 1643 2505

Drainage pumps

Unilift KP

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333 [email protected]

14

Technical data

Operating conditions

During continuous operation, the suction strainer must

always be completely covered by the liquid.

Installation

Unilift KP-S requires a minimum of space. If the pump is

installed in a pit, the pit diameter must be minimum

200 mm to avoid too many starts and stops.

Use the recommended dimensions in the table below.

Fig. 9 Pit dimensions, Unilift KP-S

IfUnilift KP-A is installed in a pit, the minimum pit dimen-

sions must be as shown in the figure below.

Fig. 10 Minimum pit dimensions, Unilift KP-A

Pump positioning

Unilift KP-M and Unilift KP-A can be used in the vertical

position with the discharge port uppermost or in the

horizontal or tilted position with the discharge port as the

highest point of the pump.

Unilift KP-S must be used in the vertical position.

Fig. 11 Pump positions

Level switches

A level switch starts and stops the pump between two

liquid levels. This type of installation requires a non-return

valve in the discharge pipe or the pump. Unilift KP pumps

are available with two different level switch types.

Unilift KP-S with electronic sensor

The sensor is integrated in the pump. Consequently, the

difference in level between start and stop cannot be

adjusted.

Fig. 12 Start-stop level, Unilift KP-S

Unilift KP-A with float switch

A clamp on the pump handle holds the float switch cable.

The difference in level between start and stop can be

adjusted by changing thefree cable length between pump

handle and float switch.

Fig. 13 Start/stop levels at min. and max. cable lengths,

Unilift KP-A

Installation depth: Max. 10 metres below liquid level

Min. liquid temperature: 0°C

Max. liquid temperature at

continuous operation: 50°C *

* At intervals of at least 30 minutes, the pump is allowed, however, to

run at maximum +70°C for periods not exceeding 2 minutes.

TM03 4674 2406

Pit diameter, D [mm] 200 250 300

Maximum inlet flow to the pit [m3/h] 0.3 0.7 1.3

TM03 4445 2106TM00 1548 0493

• • •

•

••

• •

•

••

•

••

•

••

• •

•

••

•

••

•

••••

•

••

•

••

• •

•

••

•

••

•

••••

•

••

•

••

•

••

•

••

•

••

•

••

•

••

•

D

240

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

H

B

350 mm

400 mm

TM03 4446 2106

Pump type Start

[mm] Stop

[mm]

Unilift KP-S 150

Unilift KP-S 250 205 15

Unilift KP-S 350 215 15

TM03 4446 2106

Pump type

Cable length

(L)

min. 70 mm

Cable length

(L)

max. 150 mm

Start

[mm] Stop

[mm] Start

[mm] Stop

[mm]

Unilift KP-A 150

Unilift KP-A 250 290 140 335 100

Unilift KP-A 350 300 150 345 110

Start

Stop

‹‹‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹

L

Start

Stop

Drainage pumps

Unilift KP

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333 [email protected]

15

Technical data

Performance curves

Pump dimensions

Fig. 14 Pump dimensions

* Unilift KP-350

Materials

TM03 1593 2505

0 2 4 6 8 10 12 Q [m³/h]

0

1

2

3

4

5

6

7

8

9

H

[m]

0 1 2 3 Q [l/s]

0

20

40

60

80

p

[kPa] Unilift KP

50 Hz

ISO 9906 Annex A

KP 350

KP 150

KP 250

The broken line shows a minimum liquid velocity of 0.7 m/s with a DN 32 discharge pipe to DIN EN 12056.

Pump type Supply voltage

[V] Power P1

[W] Current, In

[A] Power factor

Cos ϕ

Speed

[min-1]Capacitor

μF

KP 150 1 x 220-230 300 1.3 0.99 2900 8

KP 150 1 x 230-240

KP 250 1 x 220-230 480 2.3 0.97 2900 8KP 250 1 x 230-240 2.2

KP 250* 3 x 380-415 480 (415 V) 0.8

KP 350 1 x 220-240 700 3.2 0.99 2900 8

KP 350* 3 x 380-400 1.3

* Not available in the Unilift KP-S version.

TM03 4679 2506

TM00 1642 1093

140

214 (224*)

225 (235*)

Rp 1

14

31

149

31

140

Rp 1

214

225

14

Component Material DIN W.-Nr. AISI

Pump sleeve Stainless steel 1.4301 304

Pump housing Stainless steel 1.4301 304

Suction strainer Stainless steel 1.4301 304

Impeller Stainless steel 1.4301 304

Shaft Stainless steel 1.4057 431

Stator housing Stainless steel 1.4301 304

Guide vanes Stainless steel 1.4301 304

Bearings Carbon

O-rings

Seal rings NBR

Cables H07RN-F 3 G 1

H07RN-F 4 G 1

Drainage pumps

Unilift KP

9

Technical data Drainage pumps

KP

With float switch With vertical level switch

TM01 2059 0803

Pump type Voltage P1

[W]

In

[A]

Dimensions [mm] Weight

[kg]

HB1B2L1L2L3

KP 150 1 x 220-230 V 300 1.3 225 149 31 350 400 70 6.3

KP 150 1 x 230-240 V 300 1.3 225 149 31 350 400 70 6.3

KP 250 1 x 220-230 V 480 2.3 225 149 31 350 400 70 7.2

KP 250 1 x 230-240 V 480 2.2 225 149 31 350 400 70 7.2

KP 250 3 x 380-415 V 480 0.8 225 149 31 350 400 70 7.2

KP 350 1 x 220-240 V 700 3.2 235 149 31 350 410 70 8.0

KP 350 3 x 380-400 V 700 1.3 235 149 31 350 410 70 8.0

0 2 4 6 8 10 12 Q [m³/h]

0

1

2

3

4

5

6

7

8

9

H

[m]

0 1 2 3 Q [l/s]

0

20

40

60

80

p

[

kPa] KP

50 Hz

ISO 2548 +/- 10 %

KP 350

KP 150

KP 250

TM00 1803 1597

1

2

H

min. L

min. L3

1

2

4

1

B

Rp 1 /

TM01 1109 1098

•

••

•

••

•

• • •

•

••

•

••

•

••

•

••

•

••

•

••

•

••

•

••••

•

••

•

••

•

••

•

••

•

••••

•

••

•

••

•

••

•

••

•

••

•

••

•

••

•

••

•

ø 250 mm

400 mm

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333

iwgroup.com.au

10

Technical data Drainage pumps

KP

Installation

Pumps without level switch or with float switch can be

used in vertical position with the discharge port upper-

most or in horizontal or tilted position with the

discharge port as the highest point of the pump.

Pumps with vertical level switch must be used in vertical

position.

The KP pump is well suited for permanent installation.

Level switches

A level switch, which gives impulses to start/stop

between two levels of liquid, is connected to pumps

intended for automatic operation. This type of installa-

tion requires a non-return valve in the discharge pipe or

in the pump. The pumps are available with two different

types of level switches.

Min. liquid level: – manual operation: 14 mm.

– automatic operation: See below.

Pumps with float switch:

A clamp on the handle of the pump holds the cable of the

level switch. The difference in level between start and

stop can be adjusted by changing the free cable length

between the handle of the pump and the level switch.

Dimensions for KP 350 are marked with "#".

Pumps with vertical level switch:

For pumps with vertical level switch, the difference in

level between start and stop is not adjustable.

Dimensions for KP 350 are marked with "#".

TM00 1548 0493TM01 1492 4697

TM02 1552 2599TM01 1108 3297

••••••••••••••

••••••••••••

•••••••••••

••••••••••••

•••••••••••

••••••••••

•••••••••••

••••••••••

•••••••••

••••••••

Max.

150mm

Start

Stop

100mm

225mm

Float switch Max. 150 mm

Start

225 mm

Stop

100 mm

110 mm#

Start

Stop

80 mm

100 mm

Vertical level switch

Start

Stop

80 mm

100 mm

110 mm#

Irrigation Warehouse Group Pty Ltd

Ph 02 6732 6333

iwgroup.com.au

Grundfos Unilift KP 250 Gebrauchsanweisung

Beliebte Wasserpumpe Handbücher anderer Marken