GSi BFT Anchor Point Bedienungsanleitung

Bulk Feed Tank Anchor Point and

Self-Retracting Lanyard

Installation Manual

PNEG-1620

Version: 4.0

Date: 06-05-20

PNEG-1620

2 PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard

All information, illustrations, photos and specifications in this manual are based on the latest

information available at the time of publication. The right is reserved to make changes at any

time without notice.

Table of Contents

PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard 3

Contents

Chapter 1 Safety ..................................................................................................................................................... 4

Safety Guidelines .................................................................................................................................. 4

Cautionary Symbols Definitions ............................................................................................................ 5

Safety Cautions ..................................................................................................................................... 6

Safety Sign-Off Sheet ........................................................................................................................... 8

Chapter 2 Installation Instructions ....................................................................................................................... 9

BFT Anchor Point Installation ................................................................................................................ 9

BFT Anchor Point Usage Instructions ................................................................................................. 12

Chapter 3 Warranty .............................................................................................................................................. 15

4 PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard

1. Safety

Safety Guidelines

Safety guidelines are general-to-specific safety rules that must be followed at all times. This manual is

written to help you understand safe operating procedures and problems that can be encountered by the

operator and other personnel when using this equipment. Read and save these instructions.

As owner or operator, you are responsible for understanding the requirements, hazards, and precautions

that exist and to inform others as required. Unqualified persons must stay out of the work area at all times.

Alterations must not be made to the equipment. Alterations can produce dangerous situations resulting in

SERIOUS INJURY or DEATH.

This equipment must be installed in accordance with the current installation codes and applicable

regulations,whichmustbecarefully followed inall cases. Authoritieshavingjurisdiction mustbe consulted

before installations are made.

When necessary, you must consider the installation location relative to electrical, fuel and water utilities.

Personnel operating or working around equipment must read this manual. This manual must be delivered

with equipment to its owner. Failure to read this manual and its safety instructions is a misuse of the

equipment.

ST-0001-4

1. Safety

PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard 5

Cautionary Symbols Definitions

Cautionary symbols appear in this manual and on product decals. The symbols alert the user of potential

safety hazards, prohibited activities and mandatory actions. To help you recognize this information, we

use the symbols that are defined below.

DANGER

WARNING

CAUTION

NOTICE

This symbol indicates an imminently hazardous situation

which, if not avoided, will result in serious injury or death.

This symbol indicates a potentially hazardous situation

which, if not avoided, can result in serious injury or death.

This symbol indicates a potentially hazardous situation which,

if not avoided, can result in minor or moderate injury.

This symbol is used to address practices not related to

personal injury.

This symbol indicates a general hazard.

This symbol indicates a prohibited activity.

This symbol indicates a mandatory action.

ST-0005-2

1. Safety

6 PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard

Safety Cautions

Use Personal Protective Equipment

Eye

Protection

Hearing

Protection

Hand

Protection

Head

Protection

Respiratory

Protection Foot

Protection

Fall

Protection

• Use appropriate personal protective equipment:

• Wear clothing appropriate to the job.

• Remove all jewelry.

• Tie long hair up and back.

ST-0004-1

Follow Safety Instructions

• Carefully read all safety messages in this manual and safety signs

on your machine. Keep signs in good condition. Replace missing

or damaged safety signs. Be sure new equipment components

and repair parts include the current safety signs. Replacement

safety signs are available from the manufacturer.

• Learn how to operate the machine and how to use controls

properly. Do not let anyone operate without instruction.

• If you do not understand any part of this manual or need

assistance, contact your dealer.

ST-0002-1

Maintain Equipment and Work Area

• Understand service procedures before doing work. Keep area

clean and dry.

• Never service equipment while it is operating. Keep hands, feet,

and clothing away from moving parts.

• Keep your equipment in proper working condition. Replace worn

or broken parts immediately.

ST-0003-1

1. Safety

PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard 7

Fall Hazard

• Ladders, stairways and platforms are for use by competent and trained

personnel only. Do not allow children or other unauthorized persons to

have access to the equipment.

• Access to the equipment must be restricted by the use of security

fencing and lockable gates.

• Lower sections of ladders must be fitted with a lockable safety gate to

prevent unauthorized access.

• Make sure that hot surfaces have had adequate time to cool before

working on or in the equipment.

• Lock out and tag out power supplies and fuel supplies to all equipment.

• Do not attach lifting equipment to ladders or platforms.

• Do not go outside of the safety rails provided on elevated platforms.

• Do not work at heights during high winds, rain, snow, or ice storms.

ST-0056-1

Install and Use Anchor Point Properly

• Do not use anchor point for hoisting or lifting

bulk feed tank.

• Do not stand upright on bulk feed tank roof.

Always kneel or crawl when on bulk feed

tank roof.

• Do not use anchor point to hang from side of

bulk feed tank.

• Always use approved, self-retracting lanyard

connected to back D-ring of approved harness.

Do not connect self-retracting lanyard to front

D-ring of harness. Contact manufacturer for

details regarding approved equipment.

• Always use a tag line to retrieve and retract

lanyard. Lanyard must be fully retracted inside

sealed body of lanyard housing when not in use.

ST-0090-1

1. Safety

8 PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard

Safety Sign-Off Sheet

Below is a sign-off sheet thatcan be used to verify that all personnel have read and understood the safety

instructions. This sign-off sheet is provided for your convenience and personal record keeping.

Date Employee Name Supervisor Name

ST-0007

PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard 9

2. Installation Instructions

BFT Anchor Point Installation

The BFT anchor point is intended to provide an anchorage for a Self-Retracting Lanyard (SRL) when

climbing a BFT ladder. The anchor point has been designed for use with GSI Group’s 6', 7', 9', 12' and 15'

diameter sealed-roof bulk feed tanks.The bulk feed tank must bestructurally sound before installation can

take place. Only one individual may be attached to the anchor point at any given time.

Required Materials:

• Three 5/16" flange nuts

• Three 5/16" x 1-1/4" bolts

• One BFT anchor point (LDR-5971-SY)

Recommended Tools:

• 1/2" Wrench

• 1/2" Socket and ratchet

1. The BFT anchor point should be installed (1) at the top of the tank where the peak ring collar

meets the roof sheet. (See Figure 2A.) Utilize the existing bolt holes along the perimeter of the

peak ring collar.

Figure 2A Anchor Point Installation Location

Ref # Description

1Anchor point installation locations. Center anchor point

on the roof seam and attach to the collar.

2. Installation Instructions

10 PNEG-1620 Bulk Feed Tank Anchor Point and Self-Retracting Lanyard

2. For maximum strength, place the anchor point over a roof panel seam. (See Figure 2B.)

NOTE: The anchor point installation location (2) should be directly above the roof ladder to provide

fall protection while climbing the ladder.

Figure 2B Anchor Point Location Centered over

Roof Panel Seam

3. Once the location along the peak ring collar (3) has been identified, remove a grouping of three

existing bolts from the perimeter of the collar (3). Insert three 5/16" x 1-1/4" bolts (6) from the

underside of the roof panel (4) through the peak ring collar (3) and through the three bolt holes

on the bin anchor point (5). Secure the bolts (6) with three flange nuts (7). For placement details,

refer to Figure 2C and Figure 2D on Page 11.

Figure 2C Fastening the Anchor Point to the Roof

Ref # Description

2Anchor Point Installation Location

Ref # Description Ref # Description

3Peak Ring Collar 65/16" x 1-1/4" Bolt

4 Roof Panel 75/16" Flange Nut

5Anchor Point (LDR-5971-SY)

Inhaltsverzeichnis

Andere GSi Landwirtschaftliche Geräte Handbücher

GSi

GSi Bulk Feed Tank Series Bedienungsanleitung

GSi

GSi 40 Series Gebrauchsanweisung

GSi

GSi Cumberland Hi-Lo Bedienungsanleitung

GSi

GSi Cumberland PNEG-1333 Montageanleitung

GSi

GSi 40 Series Gebrauchsanweisung

GSi

GSi Sweep II Series Bedienungsanleitung

GSi

GSi GRA Bedienungsanleitung

GSi

GSi 40 Series Gebrauchsanweisung

GSi

GSi PNEG-1724 Bedienungsanleitung

GSi

GSi TopDry Series Bedienungsanleitung

GSi

GSi PNEG-2105 Bedienungsanleitung

GSi

GSi DMC DIII Stir-Ator Bedienungsanleitung

GSi

GSi 40 Series Bedienungsanleitung

GSi

GSi Airstream PNEG-3622000 Series Bedienungsanleitung

GSi

GSi GrainVue Bedienungsanleitung

GSi

GSi TopDry Batchflow 30 FT Gebrauchsanweisung

GSi

GSi AIRSTREAM Bedienungsanleitung

GSi

GSi 40 Series Gebrauchsanweisung

GSi

GSi 40 Series Gebrauchsanweisung

GSi

GSi 40 Series Bedienungsanleitung

GSi

GSi PNEG-4093 Gebrauchsanweisung

GSi

GSi EVO-50 Gebrauchsanweisung

GSi

GSi 12" II Series Bedienungsanleitung

GSi

GSi TopDry Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung

TURF TANK

TURF TANK One+ Bedienungsanleitung