Gude Expert Sensor Box 7211 Bedienungsanleitung

Expert Sensor Box 7211/7212

Manual Ver. 2.2.0

valid from Firmware Ver. 1.0.1

With the free Gude Control App you can retrieve all relevant information

from your GUDE products regardless of their current whereabouts. Check

with your smartphone the important operating figures of your server and

rack environment like sensor values (max/min), energy consumption as

well as state of inputs and outputs with watchdog functions. In particular,

connected consumers can be switched remotely with Gude Control.

"Gude Control" is available for the Expert Power Control 8220/8225 series

and can be free downloaded from the Google Play Store and iTunes

Store.

Have your Gude devices always in view - and in control.

3Table of contentExpert Sensor Box 7211/7212

Expert Sensor Box 7211/7212

Table of contents

Chapter 1 Device Description 4

1.1 Security Advice

1.2 Content of Delivery

1.3 Description

1.4 Installation

1.5 Status LED

1.6 Bootloader Mode

1.7 Firmware-Update

1.8 Technical Specifications

Chapter 2 Configuration 7

2.1 Configuration by Software

2.2 Configuration via Webinterface

2.2.1 Configuration - IP Address 9

2.2.2 Configuration - IP ACL 10

2.2.3 Configuration - HTTP 11

2.2.4 Configuration - Sensors 12

2.2.5 Configuration - Alarm Beeper 13

2.2.6 Configuration - SNMP 13

2.2.7 Configuration - Syslog 14

2.2.8 Configuration - E-Mail 15

Chapter 3 Protocols 15

3.1 SNMP

3.2 Syslog

Chapter 4 Support 16

4.1 Contact

4.2 Declarations of conformity

Expert Sensor Box 7211/7212 Device Description

Device Description

Security Advice

1.1

·The device must be installed only by qualified personnel according to the following installation and

operating instructions.

·The manufacturer does not accept responsibility in case of improper use of the device and particular-

ly any use of equipment that may cause personal injury or material damage.

·The device contains no user-maintenable parts. All maintenance has to be performed by factory trai-

ned service personnel.

·The device may only be connected by a low voltage power supply (12V) to 230V AC (50Hz or 60Hz).

·Always connect the device to properly grounded power sockets. To connect a Power-over-Ethernet

device, use only certified and CE marked hardware.

·The device is intended for indoor use only. Do NOT install them in an area where excessive moisture

or heat is present.

·Because of safety and approval issues it is not allowed to modify the device without our permission.

·Please note the safety advises and manuals of connected devices, too.

·The device is NOT a toy. It has to be used or stored out or range of children.

·Care about packaging material. Plastics has to be stored out of range of children. Please recycle the

packaging materials.

·In case of further questions, about installation, operation or usage of the device, which are not clear

after reading the manual, please do not hesitate to ask our support team.

·Please, never leave connected equipment unattended, that can cause damage.

Content of Delivery

1.2

The package includes:

·expert sensor box 7211/7212

·CD-ROM and manual

·Integrated P-o-E power supply (Model 7211-0 or 7212-0)

·500mA AC adaptor (Model 7211-1 or 7212-1)

Description

1.3

The sensor box 7211/7212 is a temperature sensor (7211), or a hybrid sensor (7212 - thermometer and

hygrometer) that can be connected to an Ethernet network. Integrated in the device is a Web server

and an SNMP server, which allow remote access to sensor readings. Depending on adjustable limits of

temperature and humidity the transfer of syslog messages, emails and SNMP traps can be enabled.

Expert Sensor Box 7211/7212 Device Description

Installation

1.4

Connectors on the expert sensor box 7211/7212

1. Status LED

2. Bootloader Button

3. Ethernet Port (RJ45)

4. Connector for AC Adaptor (12V DC, 0,5A)

The AC adaptor connnector is only built-in at the models 7211-1 and 7212-1.

Status LED

1.5

The Status LED shows different states of the device:

·red: Device is not connected to the Ethernet

·orange: Device is connected to the Ethernet, TCP/IP settings are not allocated

·green: Device is connected to the Ethernet, TCP/IP settings allocated

·periodic blinking: Device is in Bootloader mode.

Bootloader Mode

1.6

Certain actions can, for safety reasons, only be carried out if the device is in bootloader mode. The fol-

lowing operations are possible only in Bootloader Mode:

·Firmware Update

·Configuration with GBL_Conf.exe

·Factory Reset

Activation of the Bootloader Mode

via push button:

·Hold both buttons for 3 seconds (only if the device has 2 buttons)

Expert Sensor Box 7211/7212 Device Description

·Remove the power supply

·Hold down the button (or the "Select" button for devices with 2 buttons). If the push button is reces-

sed, use a pin or paper clip

·Connect the operating voltage

by Software: (only if "Enable FW to BL" was previously activated in GBL_Conf.exe)

·Start GBL_Conf.exe

·Do a network search with the "Search" menu action

·Activate in menu "Program Device" the item "Enter Bootloader"

Whether the device is in bootloader mode, is indicated by the flashing of the status LED, or it is shown

in GBL_Conf.exe, after a renewed device search, with the appendix "BOOT-LDR" after the device na-

me. In bootloader mode the program GBL_Conf.exe can disable the password and the IP ACL, perform

a firmware update, and restore the factory settings.

Activation of the bootloader mode and an abandonment of the bootloader does not change

the state of the power or output ports as long as the supply voltage is maintained.

Abandonment of the Bootloader Mode

via push button:

·Hold both buttons for 3 seconds (only if the device has 2 buttons)

·Remove and connect the power supply without operating a button

by Software:

·Start GBL_Conf.exe

·Do a network search with the "Search" menu action

·In menu "Program Device" activate the item "Enter Firmware"

Factory Reset

If the device is in bootloader mode, it can always be put back to its factory default. All TCP / IP settings

are reset in this operation.

via push button:

·Activate the Bootloader Mode of the device

·Hold down the button (or the "Select" button for devices with 2 buttons) for 6 seconds. If the push

button is recessed, use a pin or paper clip

·The status LED will blink in a fast rhythm, please wait until the LED blinks slowly (about 5 seconds)

by Software:

·Activate the Bootloader Mode of the device

·Start GBL_Conf.exe

·In menu "Program Device" activate the item "Reset to Fab Settings"

·The status LED will blink in a fast rhythm, please wait until the LED blinks slowly (about 5 seconds)

Expert Sensor Box 7211/7212 Device Description

Firmware-Update

1.7

To perform a firmware update, the program GBL_Conf.exe and the latest firmware is needed.

Enable the bootloader mode (see Chapter Bootloader Mode)

Start GBL_Conf.exe

Select the device for which a firmware update is to be performed

Click "Program Device" and then select there "Firmware Update"

Specify the firmware file that should be uploaded

Upon completion of the update process, please start the new firmware of the device. You can do this by

simply leaving the bootloader mode.

A firmware update, unlike other functions, is not sent as a network broadcast. Therefore, the device

must have a valid IP address and a valid netmask before the firmware update. If necessary, please cor-

rect the entries in GBL_Conf.exe in bootloader mode and save them with "Save Config".

If after a firmware update, the web page is not displayed correctly anymore, this may be related to the

interaction of Javascript with an outdated browser cache. Not always helps a Ctrl-F5, it is recommen-

ded that you manually delete the cache in the browser options. Alternatively, you can test start the

browser in "private mode".

Technical Specifications

1.8

Interfaces:

1 x Ethernet port (RJ45)

1 x Connector for AC Adaptor

Network connectivity:

10/100 MBit/s 10baseT Ethernet

Protocols:

TCP/IP, HTTP, SNMP v1 und v2c,

SNMP traps, Syslog, E-Mail (SMTP)

Power Supply:

AC Adaptor (12V DC, 0,5A)

Environment

·Operating temperature:

·Storage temperature:

·Humidity:

0°C - 50°C

-15°C - 60°C

10% - 85%

Measurements:

90mm x 25mm x 63mm (L x H x W)

Weight:

approx. 100g

Configuration

TCP/IP configuration by DHCP

After switching on the device is scanning on the Ethernet for a DHCP server and requests an unused IP

address. Check the IP address that has been assigned and adjust if necessary, that the same IP ad-

dress is used at each restart. To turn off DHCP use the software GBL_Conf.exe or use the configurati-

on via the web interface.

To check the network settings with GBL_Conf.exe, start the program and choose "All Devices" in the

"Search" menu. From the list select the appropriate device. The lower part of the left half of the window

Expert Sensor Box 7211/7212 Configuration

now shows the current network settings of the device. If the IP address is displayed with the default

settings (192.168.0.2), either no DHCP server is present on the network, or there could be no free IP

address assigned to it.

Configuration by Software

2.1

To view and change the network settings, you can use the program GBL_Conf.exe. The program is

available for free on our website www.gude.info and is also available on the accompanying CD-ROM.

You can also use GBL_Conf.exe to install firmware updates and trigger a reset to factory defaults.

Interface GBL_Conf

To check the network settings with GBL_Conf.exe, start the program and choose "All Devices" in the

"Search" menu. From the list select the appropriate device. The lower part of the left half of the window

now shows the current network settings of the device. If the IP address is displayed with the default

settings (192.168.0.2), either no DHCP server is present on the network, or there could be no free IP

address assigned to it.

·Activate the Bootloader Mode (see Chapter Bootloader Mode) and choose in menu "Search" the item

"Bootloader-Mode Devices only"

·Enter the desired settings in the edit window and save them with "Save Config".

·Deactivate the boot loader mode for the changes to take effect. Select again "All Devices" in the

"Search" menu of GBL_Conf.exe. The new network configuration is now displayed.

Configuration via Webinterface

2.2

Access the web interface: http://"IP-address" and log-in.

Expert Sensor Box 7211/7212 Configuration

Use the "Configuration" Tab to enter the configuration menu.

Configuration - IP Address

2.2.1

Hostname: Here you can enter a name with up to 15 characters. This name will be used for registration

on the DHCP server. Special characters and umlauts can cause problems in the network.

IP Address: The IP address of the device.

Netmask: The network mask used in the network.

Gateway address: The IP address of the gateway.

Use DHCP: Select "yes" if the TCP/IP settings should be obtained directly from the DHCP server:

When the function is selected, each time the device powers up it is checked if a DHCP server is availa-

ble on the network. If not, the last used TCP/IP setting will be used further.

All IP changes will take effect directly, there is no need for a restart of the firmware.

Expert Sensor Box 7211/7212 Configuration

Configuration - IP ACL

2.2.2

Reply ICMP ping requests: If you enable this feature, the device responds to ICMP pings from the net-

work.

Enable IP filter: Enable or disable the IP filter here. The IP filter represents an access control for inco-

ming IP packets.

Please note that when IP access control is enabled DHCP and SNMP only work if the appro-

priate servers and clients are registered in the IP access control list.

IP Access Control List

The IP Access Control List (ACL IP) is a filter for incoming IP packets. If the filter is active, you can on-

ly connect to hosts and subnets whose IP addresses are entered in the list.

Examples:

Entry in the IP ACL

Meaning

192.168.0.123

the PC with IP Address „192.168.0.123" can access the device

192.168.0.1/24

all devices of subnet „192.168.0.1/24“ can access

If you choose a wrong IP ACL setting and locked yourself out, please activate the Bootloader Mode and

use GBL_Conf.exe to deactivate the IP ACL.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gude Zubehör Handbücher

Gude

Gude GMS 45 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung