H-KING FRENZY Bedienungsanleitung

H-KING FRENZY

EPO SPORTS AEROBATIC MODEL WITH LED LIGHTS 1400MM

This radio controlled model is not a toy. It requires skill to fly and is not recommended

for use by beginners without assistance from an experienced model pilot. It should

not be operated by children without the supervision of a suitably experienced adult.

HobbyKing reserves the right to modify the specification of this model at any time.

WARNING

1. Do not attempt to repair or modify this aircraft with non-factory parts.

2. Never fly this model over roads, railway lines, near to power lines, airports, and do not

fly this model in excessively strong winds, rain, or thunderstorms.

3. Do not fly or launch the model towards people.

4. Keep hands and face away from the rotating propeller at all times.

5. We strongly recommend that all fixings and fasteners used in the construction of this

model are checked regularly for integrity. Failure to do so could cause a crash, injury to

yourself or others around you.

6. We only recommend the use of 2.4GHz radio equipment with this model.

SAFETY PRECAUTIONS

1. This radio controlled model is not a toy. Used incorrectly it is capable of inflicting

serious injury to persons or damage to property. The owner/pilot assumes all

responsibility for any damage to persons or property resulting from the use of this

product.

2. The manufacturer and distributor decline all responsibility for any liability arising

from use of this product.

3. It is very important that you follow all instructions for assembling and the setting up

of this model. Failure to do so could result In a loss of control and possibly a crash.

DISCLAIMER

EPO foam is a very tough and durable material perfect for the manufacture of model

aircraft. When using screwed fixings with EPO components it is important to tighten the

screws only enough to provide a firm fixing, do not over-tighten. Excess tightening

could result in the foam material becoming compressed, possibly damaging

or distorting the part. Take care to ensure that all screws are tightened sufficiently to

provide a firm fixing, do not over-tighten. We recommend that all fixings are checked

regularly for security and safety purposes..

EPO

INTRODUCTION:

SPECIFICATION:

The Frenzy offers a stunning combination of terrific looks and a sensational flight performance.

Manufactured from tough EPO it is extremely robust, however, in the event of a "less than

perfect" arrival, we supply a range of spares to get you flying again in the shortest time. It is

capable of a wide range of amazing aerobatic manoeuvres to thrill the experienced pilot, but

with reduced control throws it provides a solid and predictable flight performance, this

makes it perfect for the sports and early solo pilots.

We are certain you will enjoy your new model, please take the time to read this manual

thoroughly and understand its contents completely prior to commencing assembly.

• Wingspan:1400mm

• Length: 1130mm

• Weight: 1480g

• Motor: 3720-880KV Out-Runner Brushless

• Battery Required: 2200 - 2400mAh 11.l V LiPo (Not Included)

• Recommended Battery: 2200mAh 11.1 V 40C or greater

• ESC: 40A Brushless

• Servos: 2 x 9g, 2 x 17g

• Wing Loading: 40.3g/dm2

FEATURES:

• Powerful Brushless Motor

• 40A Brushless Electronic Speed Controller

• Efficient 2 Blade 11x7 Propeller

• Chrome Finish Spinner

• Pre-Installed Servos

• Pre-hinged Control Surfaces

• Durable EPO Construction w/Carbon

Reinforcement

• Plastic Cover on Cowl for Protection

• Steerable Tail Wheel

• Superb Flight Performance

• Excellent Power to Weight Ratio on 3S Set-up

• Very Bright LED Lighting System

• High-Viz Color Scheme

ASSEMBLY INSTRUCTIONS:

2. HORIZONTAL STABILIZER

Remove the molded tab at the end of the fuselage with a sharp knife (B). Slide the horizontal

stabilizer into the fuselage slot as shown (C). Make certain that the holes in the stabilizer line up

with the corresponding fuselage holes. If desired, a small amount of foam glue can be used for

maximum security.

B C

1. UNDERCARRIAGE

Fix the undercarriage halves into position with the

four 2.6 x 12mm self-tapping screws as shown in ( A).

If the screws become excessively tight whilst fixing,

simply back them off a tum or two, and then continue.

Note: The undercarriage legs are angled towards the

front of the fuselage.

3. VERTICAL STABILIZER & RUDDER

Install the vertical stabilizer and rudder

assembly into the slot in the fuselage. Please

make certain that the tail-wheel control wire is

located correctly in the plastic hole in the

rudder slot as shown (D).

If desired, a small amount of foam glue can be

used for maximum security. D

4. HORIZONTAL AND VERTICAL

STABILIZER FIXING

Fix the horizontal stabilizer and vertical stabilizer in

position with the two 2.6 x 35mm screws provided,

(E). The screws must be tightened sufficiently to

securely fix the parts in position, however be careful

not to over-tighten the screws.

2 x screws 2.6 x 35mm

5. TAIL CONTROL HORNS

Connect the rudder and elevator snap-links to their respective control horns as shown in images

F & G. Minor adjustment to obtain perfect neutral positions of the control surfaces can be

achieved by rotating the plastic link on the threaded portion of the control push-rod.

Make certain the plastic link is securely "snapped" closed when connected to the control horn.

6. WING ASSEMBLY

Locate the 500mm carbon wing joining spar

and slide it into the round aperture of one wing

panel. Locate the small plywood rear wing

joiner and insert it into the rectangular aperture

behind the main wing spar (H). Slide the

remaining wing panel onto the exposed portion

of the carbon spar. The plywood locking plate

will ensure perfect alignment of the two wing

halves. It is highly recommended that the joint

of the wing panels is glued together for

maximum security. Apply glue to the roots of

the wing panels and push them together, be careful that all the wires are routed correctly via the

molded slots, and that they do not foul the joint between the wing roots. Once the joint is together,

temporarily wrap some tape around the joint, then screw the wing to the fuselage to ensure the

perfect fit. Once the glue has dried, remove the wing and then the tape.

Note: The plastic connectors are

angled for the wing camber.

The Frenzy is supplied with a unique 4 way lead for

joining the aileron servos and the LED lights.

Connect two of the 4 leads to the aileron servos, and

two of the leads to the LED lights as shown (J). The

other single lead goes to the aileron port in your

chosen receiver.

7. WING FIXING

Insert the front and rear plastic connectors into the wing, (K). They are angled to provide a

perfect fit. Make certain you have them located correctly! The wing can now be fixed in

position onto the fuselage using the three M4 x 50mm screws provided.

3 x Screw M4 x 50mm

1 x

8. PROPELLER & SPINNER

1. Remove the propeller set out of its packaging.

2. Disassemble the spinner using a screwdriver.

3. Install the propeller assembly onto the motor shaft as shown in illustration (L).

4. Using a wrench on the adapter nut, tighten the assembly onto the motor shaft.

5. Re-assemble the spinner to the propeller assembly using the 2 screws.

6. Assembly of propeller unit is completer.

Securely tightening the nut will clamp the adapter to the motor shaft and fix the propeller

in position. Note: Use of excessive force will cause damage to the aluminum adapter.

Note: It is essential that the propeller is securely fixed. Failure to do

so could result in serious injury.

9. RECEIVER INSTALLATION

Connect the speed controller to the throttle channel of your receiver, (not included). This

wire is easily identified, it is the only one that is routed from the front of the model.

Connect the rudder and elevator servos to the corresponding channel outputs of the

receiver and connect the plug on the 4 way lead to the aileron channel output. There is a

molded recess in this compartment which is sufficient to accommodate most popular

2.4GHz receivers; however there is ample room elsewhere to locate yours if it does not fit

in the recess.

We recommend that it should be securely positioned with self-adhesive hook and loop tape.

You must adhere to the receiver manufacturer recommendations regarding positioning and

aerial routing.

10. BATTERY INSTALLATION

The battery compartment is accessed by gently squeezing the two raised white tags and lifting

the rear of the front hinged cover, (M). Your flight battery, (not-included) can easily be installed

and connected to the factory fitted XT60 connector, (N). Make certain the battery and cover are

both secure before flight, the battery compartment has been made bigger to except larger

batteries if required, if your battery is loose in the compartment please use some foam sponge

packing to keep it in place.

11. CONTROL SURFACES

Check that all control surfaces are centered and responding correctly to transmitter inputs.

Adjustments can be made to control surface centers by carefully rotating the plastic control

links on the threaded portion of the metal control rods. Use the servo reversing function on your

transmitter for any control that is not responding in the correct sense to control inputs. Make

certain that all plastic links are securely "snapped" closed and that all control surface hinges are

secure. Use a small amount of foam glue if any hinges are not firmly attached.

13. CENTRE OF GRAVITY

It is vital that you check that the center of gravity is correct.

Failure to do so could result in a complete loss of control.

We recommend the balance point of the model, complete

with battery, should be 75 -90mm back from the

leading edge of the wing for initial flights, (Q). Very

experienced pilots may wish to move the balance point

further back after initial flight testing.

M N

12. PROPELLER ROTATION

Double-check that the propeller is

securely fixed and it is rotating in the

correct direction, (P).

14. CONTROL SURFACE DEFLECTIONS

We suggest the following recommendations for control surface deflections. Experienced pilots

may wish to increase these movements after initial flight testing.

Ailerons: 10mm each way.

Elevator: 10mm each way.

Rudder: 12mm each way.

We hope you enjoy many happy and safe flights with your new H-King Frenzy model aircraft.

Check-out the other aircraft in the H-King range at www.hobbyking.com.

A FULL RANGE OF SPARE PARTS IS AVAILABLE FOR THE FRENZY..

SPARE PARTS:

Fuselage w/Decals

SKU: 9325000077-0

Wing w/Decals

SKU: 9325000078-0

Horizontal Stabilizer w/Decals

SKU: 9325000079-0

Horizontal Stabilizer w/Decals

SKU: 9325000080-0

Landing Gear Set

SKU: 9325000081-0

Cowling

SKU: 9325000082-0

Tailwheel Assembly

SKU: 9325000088-0

Plastic Wing Joiners

SKU: 9325000087-0

Wing Joining Rod

SKU: 9325000083-0

OrangeRx Tx6i Mode 2 6ch

2.4GHz DSM2/DSMX Compatible

Radio System

SKU: 9171001328-0

RADIOMASTER TX12 2.4GHz

Compact 12ch Multi Protocol

RC Transmitter

SKU: 9325000088-0

OrangeRx R620X V3 6Ch

2.4GHz Receiver

SKU: 9171001391-0

Rhino 2200mAh 3S 50C LiPo

Battery Pack w/XT60

SKU: 9952000025-0

Turnigy Graphene 2200mAh 3S

45C LiPo Pack w/ XT60

SKU: 9067000134-0

Turnigy Reaktor T240 AC/DC

10A 2 x 150W Charger

SKU: 995900002-3

Prop Adapter

SKU: 9325000086-0

Accessory Pack

SKU: 9325000084-0

3720-880KV Brushless Motor

SKU: 9325000085-0

RECOMMENDED ACCESSORIES:

Inhaltsverzeichnis

Andere H-KING Spielzeug Handbücher

H-KING

H-KING Savage Bobber 1000 mm 5ch ARF Version Bedienungsanleitung

H-KING

H-KING Vought f4U Corsair Bedienungsanleitung

H-KING

H-KING P-51 Mustang Bedienungsanleitung

H-KING

H-KING Night Walrus Bedienungsanleitung

H-KING

H-KING Teksumo Bedienungsanleitung

H-KING

H-KING Cloud Clipper Bedienungsanleitung

H-KING

H-KING Yak54 Bedienungsanleitung

H-KING

H-KING Sopwith Camel British WW1 Fighter Bedienungsanleitung

H-KING

H-KING GLUE-N-GO F-4 PP KIT Bedienungsanleitung

H-KING

H-KING F-35 Bedienungsanleitung

H-KING

H-KING Hummer Bedienungsanleitung

H-KING

H-KING Pacer G007 Bedienungsanleitung

H-KING

H-KING Cessna Skyline Bedienungsanleitung

H-KING

H-KING TIGER MOTH DH-82 Bedienungsanleitung

H-KING

H-KING NE-1 NAVY GUB Bedienungsanleitung

H-KING

H-KING DH82A TIGER MOTH Bedienungsanleitung

H-KING

H-KING Wargo Signature Edge 540T 3D Bedienungsanleitung

H-KING

H-KING Glue-N-Go A380 PP Kit Bedienungsanleitung

H-KING

H-KING Nori Bedienungsanleitung

H-KING

H-KING A-1 SKY RAIDER Bedienungsanleitung

H-KING

H-KING FLYCAT Bedienungsanleitung

H-KING

H-KING FG-1 Corsair Lucky Gallon Bedienungsanleitung

H-KING

H-KING j-20 Bedienungsanleitung

H-KING

H-KING MX2 Extreme 4S EP0 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung