H3C PSR180-56A Bedienungsanleitung

H3C PSR180-56A Power Module

User Manual-6PW101

BOM: 3101A0LW

Power module overview

PSR180-56A is a DC-output power module that supports both AC

and DC input. It provides a maximum output of 184 W.

The power module supports 1+1 redundancy and load sharing and is

hot swappable. It also provides overcurrent, undervoltage,

overvoltage, short circuit, overtemperature, output current limiting

protections.

Technical specifications

Table 1 Technical specifications

Item Specifications

Rated input voltage

•AC: 100 VAC to 240 VAC @ 50

Hz or 60 Hz

•DC: 240 VDC

Maximum input voltage

•AC: 85 VAC to 290 VAC @ 47 Hz

to 63 Hz

•DC: 180 VDC to 320 VDC

Maximum input current •AC: 2.5 A

•DC: 1.5 A

Output voltage 56 V

Item Specifications

Output current 3.3 A

Maximum output power 184 W

Dimensions (H × W × D) 40.1 × 82.6 × 259.5 mm (1.58 × 3.25

× 10.22 in)

Operating temperature –10°C to +55°C (14°F to 131°F)

Relative humidity 5% to 95%, noncondensing

Appearance

Figure 1 Appearance

(1) Input status LED (IN OK) (2) Power receptacle

(3) Latch (4) Handle

(5) Output status LED (OUT OK)

LEDs

Table 2 LED description

LED Status Description

Input status

LED (IN OK)

Steady green The power input is normal.

Off No power input or the power

input is abnormal.

Output status

LED (OUT

OK)

Steady green The power output is normal.

Steady red The power output is abnormal.

Off No power output.

Installing and removing the power

module

Safety precautions

To avoid possible bodily injury and power module and device

damage, follow these safety precautions:

•When you install and remove the power module, always wear

an ESD wrist strap and make sure it makes good skin contact

and is reliably grounded.

•Before you install the power module, make sure the voltage of

the power source is as required by the power module, and the

output voltage of the power module is as required by the device.

•Do not touch any cables or terminals of the power module.

•Do not place the power module in a wet area, and prevent liquid

from flowing into the power module.

•To avoid power module damage, do not open the power module.

When the internal circuits or components of the power module

fail, contact H3C Support.

Tools

Prepare an ESD wrist strap and a flat-blade screwdriver yourself.

Installing and removing the power module

Make sure the power module model is compatible with the device.

For more information about hardware compatibility, see the

installation guide for the device.

Installing the power module

To avoid bodily injury or device damage, follow the procedure

in Figure 2 to install the power module.

Figure 2 Installation procedure

To install the power module:

1. Wear an ESD wrist strap and make sure the strap makes good

skin contact and is reliably grounded.

2. Unpack the power module and verify that the power module

model is as required.

3. Remove the filler panel as shown in Figure 3, if any, from the

target power module slot.

{Put your finger into the hole in the filler panel and pull the

filler panel out along the guide rails.

{Insert a flat-blade screwdriver through the handle on the filler

panel and pull the filler panel out along the guide rails.

Figure 3 Removing a filler panel

4. Insert the power module into the slot, as shown in Figure 4:

a. Correctly orient the power module with the characters

upward.

b. Holding the power module handle with one hand and

supporting the power module bottom with the other, slide the

power module along the guide rails into the slot. When the

power module is completely inserted into the slot, you can

hear that the latch of the power module clicks into the slot.

If the power module is not aligned with the slot, pull out the

power module, adjust its direction, and insert it again.

1 2

Figure 4 Installing the power module

IMPORTANT:

Keep the filler panel and the packaging box and packaging bag

of the power module for future use.

Connecting the power cord

WARNING!

•Make sure the power cord has a separate circuit breaker.

•Turn off the circuit breaker before connecting the power

cord.

IMPORTANT:

Use the power cord provided with the power module. The powe

cord uses a C13 connector.

To connect the power cord:

1. As shown in Figure 5, plug the female connector end of the

power cord into the power receptacle on the power module.

2. Use a cable tie to secure the power cord to the handle of the

power module.

Figure 5 Securing the power cord

3. Connect the other end of the power cord to the power source,

and turn on the circuit breaker.

4. Examine the IN OK LED on the power module. If the LED is

steady green, the power cord is connected correctly. If the LED

is off, examine the installation, troubleshoot the problems, and

try again until the LED is steady green.

Removing the power module

To avoid bodily injury or device damage, follow the procedure

in Figure 6 to remove the power module.

Figure 6 Removing procedure

To remove the power module:

1. Turn off the circuit breaker at the power input end.

2. Wear an ESD wrist strap and make sure the strap makes good

skin contact and is reliably grounded.

3. Loosen the cable tie and remove the power cord.

4. As shown in Figure 7, press the latch towards the handle, and

pull the power module part way out of the slot along the guide

rails.

5. Holding the power module handle with one hand and supporting

the power module bottom with the other, pull the power module

slowly out of the slot along the guide rails.

6. Put the removed power module on an antistatic mat or into its

package.

7. If you are not to insert a power module into the empty slot, insert

the filler panel into the slot to prevent dust from entering the

chassis.

Figure 7 Removing the power module

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C SFP-GE-SX-MM850-A Bedienungsanleitung

H3C

H3C PSR2400-54A Bedienungsanleitung

H3C

H3C LSWM116FC Bedienungsanleitung

H3C

H3C PSR650C-12A Bedienungsanleitung

H3C

H3C LSQ1LBSC0 Bedienungsanleitung

H3C

H3C SecPath AC2500 Bedienungsanleitung

H3C

H3C PSR1600B-12A-B Bedienungsanleitung

H3C

H3C S9500E LSR1FW2A1 Bedienungsanleitung

H3C

H3C SecPath M9000-AI NSQM5MBSHA1 Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1CGQ20 Bedienungsanleitung

H3C

H3C PSR650B-12A2-F Bedienungsanleitung

H3C

H3C PSR250-12A1 Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C R6900-FAN Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C SIC-4G-CAT6 Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C SecPath DC2400 Bedienungsanleitung

H3C

H3C PSR250-12A Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB08D0 Bedienungsanleitung

H3C

H3C S9500 LSB1LB1A0 Bedienungsanleitung

H3C

H3C MSR Router Comware 5 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung