H3C LSXM1SEERBXD2 Bedienungsanleitung

Manual version: 6PW104-20211028

BOM: 3123A1WR

H3C LSXM1SEERBXD2 DC SeerEngine Module

1 Identifier

The module identifier LSXM1SEERBXD2 is at the right of the front panel.

2 About the module

The LSXM1SEERBXD2 is a data center (DC) SeerEngine module preinstalled with application

driven data center (ADDC) solution components such as SeerNetwork architecture (SNA) center

and SeerEngine. It can be used to build a stateless network for small and medium-sized data centers.

It enables pooling of all computing, network, and security resources and provides complete virtual

data center (vDC) capabilities, eliminating the need to install physical servers.

Figure 1 LSXM1SEERBXD2 front panel

(1) SFP+ fiber ports (3 in total)

(2) Data drive ports (SSD0 and SSD1)

(3) HDM shared network port

(4) USB 3.0 port

(5) Console port

(6) HDM dedicated network port

(7) UID button/LED

(8) Power on/standby button and system power LED

(9) Health LED

(10) HDM dedicated network port LED (ACT)

(11) HDM dedicated network port LED (LINK)

(12) HDM shared network port LED

(13) SFP+ fiber port state LED

(14) SUV port (using an SUV connector)

(15) SFP+ fiber port LEDs (ACT)

(16) SFP+ fiber port LEDs (LINK)

3 Specifications

Table 1 Module specifications

Item

Specifications

Drive •2 × 960GB system solid-state drives (SSD)

•2 × 1TB data SSDs

Memory 8 memory slots

Standard configuration: 256 GB (8 × 32 GB memory bars)

Dimensions (H × W × D) 50 × 433 × 520 mm (1.97 × 17.05 × 20.47 in)

Power consumption 140 to 285 W

SSD hot swapping Not supported

42 1

141515 16

1213

Manual version: 6PW104-20211028

BOM: 3123A1WR

Item

Specifications

Ports

•3 × 10GBASE-R-SFP+ fiber ports

•1 × 10GBASE-R-SFP+ HDM shared network port (used forEthernet

connection or HDM access)

•2 × 1TB data drive ports

•1 × SUV port (using an SUV connector)

•1 × USB 3.0 port

•1 × console port (used by technical support for debugging only)

•1 × 10/100/1000BASE-T HDM dedicated network port (default IP

address: 192.168.1.2/24)

NOTE:

The HDM shared network port obtains IP addresses through DHCP

automatically.

Ambient temperature •Operating: 5°C to 40°C (41°F to 104°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity •Operating: 5% RH to 95% RH, noncondensing

•Storage: 5% RH to 95% RH, noncondensing

Table 2 10/100/1000BASE-T management Ethernet port specifications

Item

Specification

Connector RJ-45

Standard 802.3, 802.3u, and 802.3ab

Auto-MDI/MDIX Supported

Cable Category 5 or above twisted pair cable

Transmission distance 100 m (328.08 ft)

Rate and duplex mode 10/100/1000 Mbps, full-duplex mode

NOTE:

•

This module can be used only with Type T fabric modules (such as LSXM1SFT08F2) and

Type T

supervisor engine units (such as LSXM2SUPT2).

•

To verify the compatibility of the module

with the software release you are using, see the release

notes.

•

For information about transceiver modules and cables available for the module, see the cards

and transceiver modules compatibility matrixes for the device.

4 LEDs

Table 3 LED description

LED

Status

Description

SFP+ fiber port LEDs

(LINK and ACT)

LINK ACT

Steady on Flashing A link is present on the port and the port is receiving or

sending data.

Steady on Off A link is present on the port but the port is not receiving

or sending data.

Off Off No link is present on the port.

Manual version: 6PW104-20211028

BOM: 3123A1WR

iii

LED

Status

Description

System power LED

Steady green The system has started up.

Flashing The system is starting up.

Steady amber The system is in standby state.

Off No power input exists.

Health LED

Steady green The system is operating correctly.

Flashing green HDM is being initialized.

Flashing amber (0.5 Hz) A predictive alarm has occurred.

Flashing amber (1 Hz) A general alarm has occurred.

Flashing red A severe alarm has occurred.

Off The system is not powered on or is not installed

correctly.

UID button LED

Steady on The UID LED is activated. The UID LED can be activated

by pressing the UID button or from HDM or OM.

Flashing (1 Hz) The system is being managed from HDM or the

firmware is being upgraded.

Flashing (4 Hz) HDM is restarting. To restart HDM, press the UID button

LED for 8 seconds.

Off The UID LED is not activated.

HDM dedicated

network port LED

(LINK and ACT)

LINK ACT

Steady on Flashing A link is present on the port and the port is receiving or

transmitting data.

Steady on Off A link is present on the port.

Off Off No link is present on the port.

SFP+ fiber port/HDM

shared network port

state LED

Steady on A link is present on the port.

Flashing The port is receiving or transmitting data.

Off No link is present on the port.

5 Installing and removing the module

CAUTION:

•

Wear a reliably grounded ESD wrist strap or ESD gloves when installing and removing the

module.

•Do not touch the components on the module.

5.1 Installing the module

1. Wear an ESD wrist strap, and make sure it makes good skin contact and is reliably grounded.

2. Remove the filler panel (if any) from the target slot.

This example installs the module in slot 2 on the switch.

3. Hold the module by the front panel with one hand and support the module bottom with the other.

Slide the module steadily into the slot along the guide rails.

Manual version: 6PW104-20211028

BOM: 3123A1WR

4. When most part of the module is inserted in the slot, pull the ejector levers on the module

outward.

5. Push the module until the positioning pin on the module touches the hole on the chassis.

6. Press the ejector levers inward until the ejector levers touch the panel tightly and the module

seats into the backplane.

7. Use a Phillips screwdriver to fasten the captive screws on the module.

8. Press the power on/standby button on the module to start its system. Make sure the switch has

been powered on before you press the button.

Figure 2 Installing the module

5.2 Removing the module

IMPORTANT:

Before removing the module

, press the power on/standby

button on the module for a minimum of 2

seconds until the system power LED is off.

To remove the module:

1. Wear an ESD wrist strap, and make sure it makes good skin contact and is reliably grounded.

2. Use a Phillips screwdriver to loosen the captive screws on the module.

3. Simultaneously open the ejector levers of the module to disengage the module connector from

the backplane.

4. Use one hand to slowly move the module outwards. Supporting the bottom of the module with

the other hand, pull the module out of the slot along the slide rails.

5. Place the removed module on an anti-static workbench or put it in an anti-static bag, with the

component side facing up.

6. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

Manual version: 6PW104-20211028

BOM: 3123A1WR

6 Software upgrade

For information about upgrading the software, see the release notes for the module.

The information in this document is subject to change without notice.

Inhaltsverzeichnis

Andere H3C Steuereinheit Handbücher

H3C

H3C LSWM18CQ Bedienungsanleitung

H3C

H3C LSWM116FC Bedienungsanleitung

H3C

H3C LSQM1TGT24FD0 Bedienungsanleitung

H3C

H3C PSR1800-56A Bedienungsanleitung

H3C

H3C PSR3000-54A Bedienungsanleitung

H3C

H3C SIC-4G-CAT6 Bedienungsanleitung

H3C

H3C LSQM1CGS2QSA0 Bedienungsanleitung

H3C

H3C PSR250-12A1 Bedienungsanleitung

H3C

H3C LSVM2106SFAN Bedienungsanleitung

H3C

H3C LSQ1LBSC0 Bedienungsanleitung

H3C

H3C PSR150-A1 Bedienungsanleitung

H3C

H3C SecPath M9000 NSQM1CGQ20 Bedienungsanleitung

H3C

H3C PSR6000 Bedienungsanleitung

H3C

H3C SecPath DC2400 Bedienungsanleitung

H3C

H3C SecBlade Bedienungsanleitung

H3C

H3C PSR450-12A Bedienungsanleitung

H3C

H3C S9500E LSR1FW2A1 Bedienungsanleitung

H3C

H3C S9500 LSB1LB1A0 Bedienungsanleitung

H3C

H3C LSQM1SDNB0 Bedienungsanleitung

H3C

H3C SecPath AC2500 Bedienungsanleitung

H3C

H3C SecPath PSR300-12A2 Bedienungsanleitung

H3C

H3C SecPath NSQ1FAB08D0 Bedienungsanleitung

H3C

H3C SecPath M9000-AI NSQM5AIASKA1 Bedienungsanleitung

H3C

H3C LSBM1WCM2A0 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung