H3C S7502 Bedienungsanleitung

Installation Manual

H3C S7502 Ethernet Switch Table of Contents

Table of Contents

Chapter 5 System Commissioning..............................................................................................5-1

5.1 Configuration Environment Setup......................................................................................5-1

5.1.1 Setting up Networking Environment........................................................................5-1

5.1.2 Connecting the Console Cable ...............................................................................5-1

5.1.3 Setting Terminal Parameters ..................................................................................5-1

5.2 Power-on............................................................................................................................5-5

5.2.1 Check before Power-on ..........................................................................................5-5

5.2.2 Power-on.................................................................................................................5-6

5.2.3 Check after Power-on (Recommended) .................................................................5-6

5.2.4 Starting the Interface...............................................................................................5-6

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-1

Chapter 5 System Commissioning

5.1 Configuration Environment Setup

5.1.1 Setting up Networking Environment

A terminal (a PC in this example) is connected to the switch Console port through a

Console cable.

Console cable

Switch

Serial port

Console port

Figure 5-1 Configuration environment

5.1.2 Connecting the Console Cable

Step 1: Plug the DB-9 female plug of the Console cable to the serial port of the PC or

the terminal where the switch is to be configured.

Step 2: Connect the RJ-45 connector of the Console cable to the Console port of the

switch.

5.1.3 Setting Terminal Parameters

Parameter requirements:

zBits per second: 9600

zData bits: 8

zParity: none

zStop bits: 1

zFlow control: none

zEmulation: VT100

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-2

Taking the PC running Windows XP HyperTerminal as an example, this section

introduces how to set the terminal parameters.

Note:

The terminal emulator on a Windows3.1 computer is Terminal and that on a

Windows95/Windows98/Windows 2000/Windows NT/Windows XP/Windows ME

computer is HyperTerminal.

Step 1: Start the PC and run the terminal emulator.

Step 2: Set the parameters for Windows XP HyperTerminal as follows:

1) Select Start > Programs/All Programs > Accessories > Communications >

HyperTerminal to enter the HyperTerminal window to establish a new connection

and the system will display the Connection Description dialog box.

Figure 5-2 Connection description of HyperTerminal

2) Input the name of the new connection and click <OK>. Then there pops up the

interface as shown in the following figure. Select the serial port to be used from the

“Connect using” drop down list.

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-3

Figure 5-3 Setting serial port for HyperTerminal connection

3) After selecting serial ports, click <OK>. The following interface will pop up for

setting serial port parameters. Set the bits per second to 9600, data bits to 8, parity

check to none, stop bits to 1, and flow control to none.

Figure 5-4 Setting serial port parameters

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-4

4) After setting serial port parameters, click <OK>. Then the system will enter the

HyperTerminal dialogue box as shown in the following figure.

Figure 5-5 HyperTerminal interface

In the above dialogue box, select the Properties icon to enter the properties window.

Click Settings to set the attributes (see the following figure). In this interface, select

terminal emulation mode VT100 and then click <OK>.

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-5

Figure 5-6 Setting terminal emulation mode in the property setting window

5.2 Power-on

5.2.1 Check before Power-on

Before powering on an Ethernet Switch, check that:

zThe switch has been mounted steadily.

zAll the cards have been correctly installed.

zAll the communication cables, fibers, power cables, and grounding cables have

been correctly connected.

zThe voltage of power supply meets the requirements on the switch.

zThe Console cable has been correctly connected. The computer or terminal for

configuration has been started and the terminal parameter settings have been

done.

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-6

Caution:

Before powering on the switch, confirm where the power switch of the equipment room

is located, so that you will be able to power off in case of accidence.

5.2.2 Power-on

zTurn on the power supply of the switch.

zPower on the switch.

5.2.3 Check after Power-on (Recommended)

You are recommended to check as follows after powering on the switch to ensure the

configurations thereafter.

zAfter a switch is powered on, the heat dissipation system starts working. You can

hear the noise as the fan rotates and feel air flow out from the vent.

zCheck if any system indicator on the SRPU indicates abnormal condition.

5.2.4 Starting the Interface

As the switch is started, the configuration terminal will yield the following output:

Starting......

RAM Line....OK

System is booting................

******************************************

* *

* H3C S7502 BOOTROM, Version 530 *

* *

******************************************

Creation date : Apr 20 2007, 14:48:52

CPU type : MPC8245

CPU Clock Speed : 300Mhz

BUS Clock Speed : 33Mhz

BOOT_FLASH type : M29W040B

Flash Size : 32MB

Memory Size : 256MB

S7502 main board self testing................................

SDRAM Data lines Selftest.................................OK!

SDRAM Address lines Selftest..............................OK!

Installation Manual

H3C S7502 Ethernet Switch Chapter 5 System Commissioning

5-7

SDRAM fast selftest.......................................OK!

Please check LEDs.....................LEDs selftest finished!

CPLD selftest.............................................OK!

The switch Mac address is .....................0000.0309.0004

Press Ctrl+B to enter Boot Menu... 0

Auto-booting...

Auto booting file is S7502.app

There are 4 files in this packet

SRPG app file <<srpu.app>> is...OK

Decompress Image...................................................

.......................................................OK!

Starting at 0x60000...

..........................................................................

................................ .........................................

................................................................. ........

..........................................................................

User interface Aux0/0 is available

Press ENTER to get started.

The displaying of the above indications indicates the completion of the switch

auto-booting.

Press <Enter> and you will get the following output. By this time, you can start

configuring the switch.

<H3C>

Note:

The S7502 provides a variety of command views. For the specific descriptions on the

configuration commands and command line interfaces, refer to H3C S7500 Series

Ethernet Switches Operation Manual and H3C S7500 Series Ethernet Switches

Command Manual.

Andere Handbücher für S7502

Inhaltsverzeichnis

Andere H3C Netzwerk-Router Handbücher

H3C

H3C S3610 Series Montageanleitung

H3C

H3C S3600V2 SERIES Bedienungsanleitung

H3C

H3C MSR 20-1X Bedienungsanleitung

H3C

H3C WA6126 Bedienungsanleitung

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C MSR5620 Bedienungsanleitung

H3C

H3C MSR 2600 Series Bedienungsanleitung

H3C

H3C MSR 2600 Bedienungs- und Wartungshandbuch

H3C

H3C CR19000-20 Bedienungsanleitung

H3C

H3C SR6600 Series Bedienungsanleitung

H3C

H3C S7500 Series Bedienungsanleitung

H3C

H3C SR8800-X Bedienungs- und Wartungshandbuch

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S12500R-2L Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C MSR600 Series Bedienungsanleitung

H3C

H3C MSR3600-28-X1 Bedienungsanleitung

H3C

H3C SR6604-X Bedienungs- und Wartungshandbuch

H3C

H3C MSR Series Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C S5120-EI Series Bedienungsanleitung

H3C

H3C MSR Series Bedienungsanleitung

H3C

H3C RA200 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise