H3C SecPath F5010 Bedienungs- und Wartungshandbuch

H3C SecPath F5010/F5020/F5040 Firewall Installation Quick Start-6W105

H3C SecPath F5010/F5020/F5040 防火墙快速安装指南-6W105

Tool List 工具参考

The installation tools are not provided with the firewall. Prepare them yourself.

防火墙不随机提供安装工具，请用户根据实际安装需求自备安装工具。

Introduction to Installation Accessories 安装附件介绍

Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good

skin contact and is well grounded.操作者需佩戴防静电腕带，确保防静电腕带与

皮肤良好接触，并确认防静电腕带已经良好接地。

Phillipsscrewdriver

十字螺丝刀Needle-nosepliers

尖嘴钳Wire-strippingpliers

剥线钳

Diagonal pliers

斜口钳Marker

记号笔

Flat-bladescrewdriver

一字螺丝刀

Wirecrimper

压线钳ESD-preventivewriststrap

防静电腕带

Mountingbracket

(required)

挂耳(标配)

Rubberpads

(required)

胶垫贴(标配)

Groundingcable

(required)

地线(标配)

Cagenut

(usersupplied)

浮动螺母(用户自备)

M6screw

(usersupplied)

M6螺钉(用户自备)

Removable cable tie

(usersupplied)可拆卸式扎带

(用户自备)

Bail latch

(required)

电源卡钩(标配)

M4countersunk-head

screw(required)

M4沉头螺钉(标配)

Attachtherubberpadstothefourroundholesin the

chassis bottom.Placethefirewall withupsideupon

theworkbench.粘贴胶垫到防火墙底部，将带胶垫贴

的防火墙平放到工作台上。

Mounting the Firewall to a Workbench 安装防火墙到工作台

Make sure the workbench is sturdy and well grounded. Avoid placing heavy objects

on the firewall.保证工作台的平稳与良好接地，并且不要在防火墙上放置重物。

Airflow of the Firewall 防火墙的风道设计

Make sure the air inlet and outlet vents are not blocked and the installation site

has a good ventilation system.请确保防火墙的进、出风孔不被遮挡，并将防火墙

安装在具有良好通风散热系统的环境中。

Thefirewall adoptsleft-to-rightair aisles.

防火墙采用左进右出的风道设计。

The F50X0 series includes the F5010, F5020, and F5040.The installation

procedures for these firewalls are similar.This guide uses the F5020 as an

example. F50X0系列包含F5010/F5020/F5040款型，各款型安装方式类似，本手

册仅以安装F5020方式举例说明。

Attachthemountingbracketstothefirewall.

安装防火墙的挂耳。

Mounting the Firewall to a Rack 安装防火墙到机柜 To avoid bodily injury and firewall damage, use at least two people to mount the

firewall to the rack because the firewall is heavy.由于防火墙较重，安装到机柜时

至少需两人配合完成，以免造成防火墙及人身伤害。

Placethefirewall in therackandsecurethefirewall totherackpostswithM6screws.

将防火墙安装进机柜中，用M6螺钉将防火墙固定在机柜上。

Markthepositionsofthecagenuts

ontherackpostbyusinga

mountingbracket.用挂耳比对出机

柜立柱方孔条上浮动螺母的位置，

并用记号笔标出。

Install thecagenutstothemarked

positionsontherackpost.

安装浮动螺母。

Acagenutis installedto therack

post.浮动螺母安装完毕。

The information in this document is subject to change without notice.

本文档中的信息如有更改，恕不另行通知

如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com

The firewall does not support hot-swapping of the interface cards. Power off the

firewall before you install or remove an interface card.

设备不支持接口板的热插拔，安装/拆卸时请先关闭电源。

BOM:3104A0C0

Connecting the Grounding Cable 连接保护地线

Correctly connecting the firewall grounding cable is crucial to lightning protection

and EMI protection. To guarantee the grounding effect, use the grounding cable

provided with the firewall. 防火墙保护地线的正确连接是防雷、防干扰的重要保障，

请使用防火墙随机提供的保护地线正确接地。

Installing an interface card 安装接口板

Installing a Power Module 安装电源模块

Whenyoumountthefirewall toaworkbench,youcanconnectthegroundingcable toa

groundingstrip.如果设备安装在工作台,可以将保护地线连接到接地排.

Whenyoumountthefirewall toarack,youcan

connectthegroundingcable to thegrounding

terminal oftherack.如果防火墙安装在机柜，

可以将保护地线连接到机柜接地端子。

2.UsethePhillipsscrewdrivertotightenthecaptivescrews.

用十字螺丝刀拧紧松不脱螺丝。

1. Remove the filler panel from the power module.拆卸电源槽位假面板。

2. Insert the AC or DC power module.插入AC/DC电源模块。

3. Tighten the captive screws.旋紧固定螺钉。

The AC and DC power modules cannot work together on the firewall.

防火墙不支持直流和交流电源模块混插。

Connecting the Power Cable 连接电源线

Connect the AC power cable.

连接交流电源线。 Connect the DC power cable.

连接直流电源线。

Before connecting the power cable, make sure the firewall is properly grounded.

To avoid bodily injury, make sure the firewall is powered off.连接电源线前，需保

证设备已良好接地。严禁带电连接电源线，以免造成人身伤害。

1.Removethefillerpanel fromtheinterfacecardslot.Rotatethetwoejectorleversof

theinterface cardoutwardandinsertthecardalongtheguiderails intotheslot.

拆卸接口板槽位假面板，并将接口扳两端扳手向外扳，然后将接口板沿着插槽导轨水平

缓慢的推进插槽。

Install a DC power module.

安装直流电源模块。

Install an AC power module.

安装交流电源模块。

1 1

3 3

Dieses Handbuch passt für folgende Modelle

Andere H3C Netzwerk-Router Handbücher

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C MSR 2600 Series Bedienungsanleitung

H3C

H3C RA10 Bedienungs- und Wartungshandbuch

H3C

H3C MSR Series Installationshandbuch

H3C

H3C S6300 Series Bedienungsanleitung

H3C

H3C S5150-EI Series Bedienungsanleitung

H3C

H3C S12508CR Bedienungs- und Wartungshandbuch

H3C

H3C MSR 30-16 Handbuch

H3C

H3C CR16000-M Bedienungsanleitung

H3C

H3C MSR Series Installationshandbuch

H3C

H3C H3C S3600 Series Montageanleitung

H3C

H3C S3100 Series Bedienungsanleitung

H3C

H3C S5500-SI Series Bedienungsanleitung

H3C

H3C SR8800-X Bedienungsanleitung

H3C

H3C MSR 930 Bedienungsanleitung

H3C

H3C RA10 Bedienungsanleitung

H3C

H3C S3100 Series Montageanleitung

H3C

H3C S3100-52P Montageanleitung

H3C

H3C S9500 Series Bedienungsanleitung

H3C

H3C MSR 20-20 Handbuch

H3C

H3C MSR 20-20 Bedienungsanleitung

H3C

H3C AR 18-3XE Series Bedienungsanleitung

H3C

H3C CR16000-F Installationshandbuch

H3C

H3C H3C S3600 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise