H3C SecPath M9000-S NSQM2MPUD0 Bedienungsanleitung

Manual version: APW100-20171225 BOM: 3123A1Q1

H3C SecPath M9000-S NSQM2MPUD0 main

processing unit

1 Identifier

The module identifier NSQM2MPUD0 is at the upper right corner of the front panel.

2 Specifications

The NSQM2MPUD0 MPU has a console port, a USB port, a Mini USB console port, two

10/100/1000Base-T copper ports, and two GE SFP fiber ports.

Figure 1 Front panel

(1) 10/100/1000Base-T copper port LEDs (LINK and ACT) (2) SFP port LEDs (LINK and ACT)

(3) Power module status LED (PWR) (4) Module status LEDs

(5) Active/standby state LED (ACTIVE) (6) Reset button (RESET)

(7) Fan tray status LED (FAN) (8) GE SFP fiber port

(9) 10/100/1000Base-T copper port (10) Console port (CONSOLE)

(11) USB console port (12) USB port

(13) Ejector lever (14) Captive screw

Table 1 Module specifications

Item Specifications

Flash 1 GB

SDRAM (DDR3) 4 GB

Dimensions (H × W × D) 45 × 399 × 355 mm (1.77 × 15.71 × 13.98 in)

Power consumption 45 to 86 W

Weight 4 kg (8.82 lb)

Hot swapping Supported

Port

•1 × console port

•1 × USB console port

•1 × USB 2.0 port

•4 × network management ports, including two 10/100/1000Base-T

ports and two SFP ports

Manual version: APW100-20171225 BOM: 3123A1Q1

Item Specifications

Ambient temperature

•Operating: 0°C to 45°C (32°F to 113°F)

•Non-operating: –40°C to +70°C (–40°F to +158°F)

Ambient humidity

•Operating: 10 to 95% RH, noncondensing

•Non-operating: 5% RH to 95% RH, noncondensing

Compatible device models and

slots M9008-S gateway (slots 0 and 1)

IMPORTANT:

•To verify compatibility of the MPU with the software release you are using, see the release notes.

•To connect an SFP fiber management Ethernet port on the MPU, make sure the peer port

operates at 1000 Mbps in full-duplex mode.

•The USB port on the MPU does not support USB extension cables.

Table 2 Console port specifications

Item Specifications

Connector type RJ-45

Interface standard RS-232

Transmission baud rate 9600 bps (default) to 115200 bps

Transmission medium Asynchronous serial cable

Transmission distance ≤15 m (49.21 ft)

Services

•Provides connection to an ASCII terminal.

•Provides connection to the serial port of a local PC running

terminal emulation program.

•Supports command line interface (CLI)

Table 3 10/100/1000BASE-T Ethernet copper port specifications

Item Specifications

Connector type RJ-45

Interface standard 802.3, 802.3u, and 802.3ab

Interface type MDI/MDIX autosensing

Transmission medium Category-5 (or above) twisted pair cable

Transmission distance 100 m (328.08 ft)

Transmission rate and working

mode

•10 Mbps, half/full duplex

•100 Mbps, half/full duplex

•1000 Mbps, full duplex

Table 4 1000BASE-X SFP fiber port specifications

Item Specifications

Connector type LC

Transmission medium and

maximum transmission distance SFP transceiver modules: see Table 5.

Manual version: APW100-20171225 BOM: 3123A1Q1

iii

Item Specifications

Interface standard 802.3, 802.3u, and 802.3ab

Transmission rate and working

mode 1000 Mbps, full duplex

Table 5 SFP modules available for the 1000BASE-X SFP fiber ports

Module Central

wavelength Connector

type Cable

specifications

Maximum

transmission

distance

SFP-GE-SX-MM850-A 850 nm LC

50/125 µm

multi-mode optical

fiber (MMF)

550 m (0.34 miles)

62.5/125 µm MMF 275 m (0.17 miles)

SFP-GE-SX-MM850-D 850 nm LC

50/125 µm MMF 550 m (0.34 miles)

62.5/125 µm MMF 275 m (0.17 miles)

SFP-GE-LX-SM1310-A 1310 nm LC

9/125 µm

single-mode

optical fiber (SMF)

10 km (6.21 miles)

50/125 µm MMF 550 m (1804.46 ft)

62.5/125 µm MMF 550 m (1804.46 ft)

SFP-GE-LX-SM1310-D 1310 nm LC

9/125 µm SMF 10 km (6.21 miles)

50/125 µm MMF 550 m (1804.46 ft)

62.5/125 µm MMF 550 m (1804.46 ft)

SFP-GE-LH40-SM1310 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)

SFP-GE-LH40-SM1310-D 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)

SFP-GE-LH40-SM1550 1550 nm LC 9/125 µm SMF 40 km (24.86 miles)

SFP-GE-LH80-SM1550 1550 nm LC 9/125 µm SMF 80 km (49.71 miles)

SFP-GE-LH80-SM1550-D 1550 nm LC 9/125 µm SMF 80 km (49.71 miles)

SFP-GE-LH100-SM1550 1550 nm LC 9/125 µm SMF 100 km (62.14 miles)

SFP-GE-LX-SM1310-BIDI RX: 1490 nm

TX: 1310 nm LC 9/125 µm SMF 10 km (6.21 miles)

SFP-GE-LX-SM1490-BIDI RX: 1310 nm

TX: 1490 nm LC 9/125 µm SMF 10 km (6.21 miles)

NOTE:

•BIDI modules use different central wavelengths in transmit and receive directions to implement

bidirectional transmission of optical signals over the same fiber.

•BIDI modules must be used in pairs. For example, if an SFP-GE-LX-SM1310-BIDI is used at one

end, you must use an SFP-GE-LX-SM1490-BIDI at the other end.

Manual version: APW100-20171225 BOM: 3123A1Q1

3 LEDs

Table 6 LED description

LED Status Description

10/100/1000Base-T

/SFP port LED

(LINK and ACT)

•LINK LED: On

•ACT LED: Flashing A link is present on the port and the port is sending or

receiving data.

•LINK LED: On

•ACT LED: Off A link is present on the port.

•LINK LED: Off

•ACT LED: Off No link is present on the port.

Power module

status LED (PWR)

Green All the power modules in position are operating correctly.

Red

A power module is not outputting power. The reason

might be power module failure, power switch turned off,

power cord connection fault, or mains power failure.

Off

•No power modules are installed in the chassis.

•No power modules in position are outputting power.

The reason might be power modules failure, power

switches turned off, power cords connection fault,

or mains power failure.

Fan tray status LED

(FAN)

Green •The fan tray is operating correctly.

Red •The fan tray is faulty or is not in position.

Off •The device is not powered up.

Module status LED

Flashing green •The module is operating correctly.

Fast flashing green (4 Hz)

•The module is uploading software. If the LED

remains in this state, the module software does not

match the device software.

Steady red •The module is starting up or is faulty.

Flashing red

•The module temperature is higher than the upper

warning threshold or lower than the lower warning

threshold.

Off •The module is not in position.

Active/standby

state LED

(ACTIVE)

On •The MPU is operating in active state.

Off

•The MPU is operating in standby state.

•The MPU is faulty. To determine whether the MPU

is faulty, observe also the module status LEDs.

4 Installing and removing the MPU

CAUTION:

•Wear a reliably-grounded ESD wrist strap or ESD gloves when you install or remove the MPU.

•Do not touch the components on the PCB.

Manual version: APW100-20171225 BOM: 3123A1Q1

4.1 Installing the MPU

1. Face the front panel of the device. Remove the filler panel from the target slot.

This example uses slot 0 on the device.

2. Place the MPU horizontally on a workbench with the PCB facing up. Pull outward the ejector

levers on the MPU.

3. Gently push the MPU into the slot along the guide rails.

4. Push the ejector levers inward until the MPU is in close contact with the backplane.

5. Use a Phillips screwdriver to tighten the captive screws on the MPU.

Figure 2 Installing the MPU

4.2 Removing the MPU

1. Use a Phillips screwdriver to loosen the captive screws on the MPU until all pressure is

released.

2. Simultaneously pull the ejector levers at both sides of the MPU outward to separate the MPU

from the backplane, and pull the MPU slowly out of the chassis along the guide rails.

3. Place the MPU on an anti-static workbench with the PCB facing up, or put it in an anti-static

bag.

4. If you are not to install a new MPU, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

5 Software upgrade

For information about upgrading the MPU, see the release notes.

6 Obtaining documentation

To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:

1. Go to http://www.h3c.com.hk/Technical_Documents.

2. Choose the desired product category and model.

Inhaltsverzeichnis

Andere H3C Netzwerk-Router Handbücher

H3C

H3C S3100-52P Montageanleitung

H3C

H3C S7500 Series Bedienungsanleitung

H3C

H3C CR16000-FA Series Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Installationshandbuch

H3C

H3C MSR810 Bedienungsanleitung

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C MSR 30-10 Bedienungsanleitung

H3C

H3C AR 18-3XE Series Bedienungsanleitung

H3C

H3C CR16000-F Installationshandbuch

H3C

H3C WT2024-U-PWR Bedienungsanleitung

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C CR16000-M Bedienungsanleitung

H3C

H3C S5830V2 series Bedienungsanleitung

H3C

H3C SecPath L5000-S Bedienungs- und Wartungshandbuch

H3C

H3C S5500-HI Switch Series Bedienungsanleitung

H3C

H3C MSR810 Installationshandbuch

H3C

H3C MSR900-E Series Bedienungsanleitung

H3C

H3C SR6608 Bedienungs- und Wartungshandbuch

H3C

H3C MSR 5600 Bedienungs- und Wartungshandbuch

H3C

H3C MSR-20-21 ROUTER Bedienungsanleitung

H3C

H3C MSR 20-20 Handbuch

H3C

H3C MSR Series Bedienungsanleitung

H3C

H3C H3C S3600 Series Montageanleitung

H3C

H3C MSR 5600 Bedienungs- und Wartungshandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung