Hachette Agora Models BISMARCK Handbuch
STAGE 09: GEARBOX FOR THE
BOW ANCHORS: 2
STAGE 10: THE SECOND SECTION
OF THE UPPER DECK
STAGE 11: THE PORT HULL AND SUPPORT STAND
STAGE 12: GEARBOX FOR THE
FORWARD GUN TURRET
STAGE 13: HINGED SUPPORTS FOR
THE BREAKWATER
STAGE 14: MOTOR FOR THE FORWARD
GUN TURRET
STAGE 15: HULL ASSEMBLY AND SUPPORTS
FOR THE FORE BREAKWATER
STAGE 16: FORWARD GUN ELEVATION MOTOR
STAGE 17: WIRING FOR
THE FORWARD TURRET
STAGE 18: TESTING THE
WIRING OF THE TURRET
STAGE 19: THE JACKSTAFF
AND BOW LIGHT
STAGE 20: ANOTHER SECTION OF THE HULL
Pack 02 |Build Instructions
Your 1:200 scale model of the legendary battleship Bismarck is packed with
intricate details which precisely replicate every aspect of this state-of-the-
art warship. Each piece has been created using premium quality materials to
bring maximum enjoyment during your complete build.
In your second model pack, you will assemble:
© 2020 Hachette Partworks Ltd.
North America Edition by Agora Models
Not suitable for children under the age of 14. This product is not a toy and is not designed for use in play. Keep
the parts out of the reach of small children. Some parts may have sharp edges. Please handle them with care.
Advice from the experts
Spare screws are included with each part. Occasionally, you may
be instructed to keep spare or unused screws for a later stage.
Keep these spares in a safe place and label them correctly.
Please make sure you don’t mix up the screws. They look quite
similar, but the threads do vary slightly. Using the wrong screws
may damage the parts.
When securing parts together using multiple screws, fit each
screw loosely to ensure all the parts are correctly aligned before
gently tightening them firmly, but not overtight, in the order in
which you placed them.
The screwdriver can be magnetised by stroking it with a magnet
(fridge magnet, etc.) enabling it to hold the screws and make
assembly easier.
If a screw is tight going into a metal part, do not force it as you
may shear the head off. Remove it and put a tiny smear of Vaseline,
soap or light oil on the thread. That will lubricate it and make it
easier to drive home.
During the course of this build, you will receive many pieces that
you will assemble immediately – following the instructions in the
corresponding stage – and other pieces that you should store
safely to one side, for use in future assembly stages.
22
AGORAMODELS BISMARCK 3
AGORAMODELS BISMARCK
702
904
905
01. MOUNTING THE GEARS AND SHAFTS
STAGE 09
GEARBOX FOR THE BOW ANCHORS: 2
01
905
902
901 903 904
906 907
Take the upper part of the gearbox
housing 7-02, which was assembled
in stage 7. Insert a shaft 9-05 into
the hole in the middle of the
gearbox housing as shown. Identify
the cog 9-04. Note that this has a
smaller cog at the centre whereas
the similar cog 9-03 has a peg at
the centre.
COMPONENTS CHECKLIST
9-01: Two cogs with
shafts
9-02: Double cog with
shaft
9-03: Cog with peg
9-04: Cog
9-05: Two shafts
9-06: Anchor motor
9-07: Switch
PB Eleven 2 x 6 mm
screws
3
2
AGORAMODELS BISMARCK 3
AGORAMODELS BISMARCK
Fit the cog 9-03 onto shaft 9-05. Make sure that
the peg (indicated by the arrow) is at the angle
shown. See also section 02, photo 4.
Fit the cog 9-04 onto the shaft 9-05. Fit the second
shaft 9-05 into the hole near the end of the gearbox
as shown. Identify the cog with a peg 9-03.
Holding the gearbox above the worksurface, take
the two cogs with shafts 9-01. One end of the shaft
has splines which pass through the gearbox
housing to protrude on the other side. Fit the
shafts into the holes either side of the central cog.
Holding the gearbox above the worksurface, fit
the shaft of the gear 9-02 into the hole in the
gearbox on the other side of cog 9-04 as shown.
Fit the motor and lengthwise shaft assembly
9-06/ 7-05 into the gearbox housing. Make sure
that the sprockets of the cogs on the shaft
(indicated by the arrows) engage with the cogs
7-03 and 9-02.
Take the lengthwise shaft 7-05 supplied with
stage 7 and fit the grey end onto the shaft of the
anchor motor 9-06, as indicated by the arrow.
903
906
705
904 905 903 905
902 901
901
705
906
902
703
02. INSTALLING OF THE ANCHOR MOTOR AND SWITCH
02 03
04 05
0201
904
44
AGORAMODELS BISMARCK 5
AGORAMODELS BISMARCK
03
05
01
Insert the switch 9-07 in the gearbox housing
so that its pin is to the left of the peg on cog
9-03 (see inset).
When fitting the anchor motor 9-06 into the
gearbox, make sure that the cables run upwards
(as indicated by the arrow).
Secure the two parts of the gearbox together
using six PB screws as shown.
Take the lower part of the gearbox housing 7-01
and, after checking the shafts are correctly
aligned, fit it on top of the upper section 7-02.
Position the gearbox 7-02 on the four raised sockets
on the underside of the upper deck 1-01. Taking care
not to damage the deck details, fix the gearbox
housing in place with four PB screws. Carefully turn
the fore section of the upper deck right side up.
Turn the fore section of the upper deck 1-01 upside
down, taking great care not to damage any of the
details fitted previously. Take the gearbox housing
and thread the two anchor chains 7-06 through
the small holes in the upper deck (indicated by the
arrows).
907
903
701
702
701
PB
101
706
PB
PB
03. FITTING THE GEARBOX AND ANCHOR CHAINS
04
06
02
5
4
AGORAMODELS BISMARCK 5
AGORAMODELS BISMARCK
102
104
706
805
505
505
104
902
901
901
506 505
508
706
506 505
508
706
805
706
Fit the two capstans 5-05 assembled in stage 05,
on the splines on the ends of shafts 9-01 (see also
two arrows in photo 3). Note that the green
capstan should be on the starboard (right) side
and the red capstan on the port (left).
Apply a little superglue to the bottom of the
capstan head 1-04 supplied with stage 01. Glue
part 1-04 to the end of shaft 9-02, which
protrudes through the hole in the warping
winch baseplate 1-02. Two other shafts show
through holes in the deck (indicated by arrows).
Wrap the port anchor chain 7-06 around the
red capstan 5-05. Again, it passes between the
shaft 5-06 and the anchor chain guide 5-08.
Take the starboard anchor chain 7-06 and wrap
it around the base of the green capstan 5-05.
The chain should run between the shaft 5-06
and the anchor chain guide 5-08.
The starboard anchor chain 7-06 runs from the
capstan drum towards the bow and beneath the
anchor bracket 8-05.
Thread the port anchor chain 7-06 along the
upper deck towards the bow and through the
anchor bracket 8-05.
03
05
0807
04
06
66
AGORAMODELS BISMARCK 7
AGORAMODELS BISMARCK
706
707
709
709 706
707
01
02
04. ATTACHING THE TWO SIDE BOW ANCHORS
Take out the two anchors
assembled in stage 07. Take one of
the anchor chains 7-06 and a ring
7-07. Carefully lever the ring open
so that you can thread it through
the last link in the chain. You may
find it helpful to use tweezers and a
magnifying glass.
Completed work
The gearbox for the bow anchor is
completed and mounted under
the forward section of the deck.
The anchor chains have been
positioned so that they wrap
around the capstans, and the
anchors have been attached to
the chains.
Repeat the last step on the other
side of the upper deck so the second
ring 7-07 is threaded through the
last link on the second anchor chain
7-06 as shown.
7
6
AGORAMODELS BISMARCK 7
AGORAMODELS BISMARCK
1001
1002 1002
1001
01. THE BARBETTE FOR THE FOREMOST TWIN TURRET
STAGE 10
THE SECOND SECTION
OF THE UPPER DECK
01
The main photo shows the barbette 10-02 in
place on the upper deck section 10-01. The
inset shows the two parts from underneath
with the four tabs fitted into the recesses.
Place the second upper deck section 10-01 on
your work surface. Take the barbette 10-02 and
insert it in the opening on the upper deck. The
four tabs should fit in the recesses (as indicated
by the arrow).
1001
1003
1002
1004
1005
1006 1007
1009
1008
1010
02
COMPONENTS CHECKLIST
10-01: Second section
of the upper
deck
10-02: Barbette (turret A)
10-03: Fore breakwater
10-04: Vent
10-05: Two skylights
10-06: Vent
10-07: Vent
10-08: Hatch
10-09: Handwheel
10-10: Five skylights
PB: Five 2 x 6 mm
screws
88
AGORAMODELS BISMARCK 9
AGORAMODELS BISMARCK
Fix the breakwater 10-03 in place so the tabs on
10-03 fit into the recesses at the front edge of the
upper deck section 10-01. It is helpful to use
tweezers for this step.
Place the front breakwater 10-03 upside down in
front of the upper deck section 10-01. Apply
thick superglue to the four tabs on the
breakwater (circled).
Glue the vents 10-06 and 10-07 into the
recesses in the front area of the upper deck
section 10-01, as shown.
The handwheel 10-09 is fitted behind the
breakwater 10-03. Apply a little thick superglue
to the peg on the base of 10-09 to fix it in place.
Take the two skylights 10-05. Check their orientation
in the recesses on the deck into which they fit. Apply
thick superglue to the undersides of the skylights
10-05 and fix in place on the deck section as shown.
The vent 10-04 is also positioned in the front
area of the upper deck section. Apply a little glue
to the peg on the base of 10-04 to hold it in
place.
02. DETAILS FOR THE SECOND UPPER DECK SECTION
01
03 04
0605
1001
1003 1003
1009
1003
1006 1007
1004
1005
1005
02
9
8
AGORAMODELS BISMARCK 9
AGORAMODELS BISMARCK
01
At the very back of the upper deck section identify
the recesses for the five identical skylights 10-10
behind the barbette. Glue them in place.
Take the hatch 10-08 and glue it in place behind
the handwheel on the upper deck section as
shown.
Fit the lip on the edge of the forward deck
section 1-01 over the raised screw sockets on the
second deck section 10-01. Again, take care not
to damage any of the parts on the other side. Fix
them together with four PB screws.
Taking care not to damage any of the parts that
have already been fitted, turn the front of the
upper deck 1-01 and the second upper deck
section 10-01 upside down. You will need four
PB screws to fix them together.
Completed work
The second upper deck section has
been fitted with various details and
then attached to the forward section
of the upper deck.
03. ASSEMBLING THE UPPER DECK PARTS
02
101
1008 1010
1001 1001
101
PB
PB
07 08
10 10
AGORAMODELS BISMARCK 11
AGORAMODELS BISMARCK
Andere Handbücher für Agora Models BISMARCK
1
Inhaltsverzeichnis
Andere Hachette Spielzeug Handbücher
Hachette
Hachette Agora Models BISMARCK Handbuch
Hachette
Hachette ALIEN spectacular Bedienungsanleitung
Hachette
Hachette ALIEN XENOMORPH Bedienungsanleitung
Hachette
Hachette ALIEN Bedienungsanleitung
Hachette
Hachette ALIEN PACK 8 Handbuch
Hachette
Hachette ALIEN PACK 4 Handbuch
Hachette
Hachette ALIEN PACK 6 Handbuch
Hachette
Hachette ALIEN PACK 7 Handbuch
Hachette
Hachette U-BOAT U 96 Bedienungsanleitung
Hachette
Hachette ALIEN spectacular Produktinformationsblatt
