Hachette ALIEN XENOMORPH Bedienungsanleitung
ALIEN
BUILD THE
TERRIFYING
XENOMORPH
FROM
ALIEN
spectacular
EASYEASY
ASSEMBLYASSEMBLY
1:2
PACK 1
KITS 1 - 4
Non contractual visual
scale
Hachette Partworks Ltd, 4th Floor, Jordan House,
47 Brunswick Place, London N1 6EB
www.hachettepartworks.com
© 2023/2024 Hachette Partworks Ltd.
© 2023 20th Century Studios.
ALL RIGHTS RESERVED
All parts belong to a kit. Collectors item for adults.
Not suitable for children under 14.
PACK 1 | BUILD INSTRUCTIONS
ALIEN
WARNING: Some parts are assembled using magnets. These magnets can cause serious
injury if they are swallowed. Keep away from children. If you suspect a magnet has been
swallowed, seek medical help straight away.
Some parts may have sharp edges, please handle them with care.
The installation of electronic parts must always be carried out by an adult. When replacing batteries,
use the same type of batteries.
Please ensure that the battery compartment is securely fastened before you use the model again.
Used batteries should be recycled.
Please make sure to check with your local council how batteries should be disposed of in your area.
Batteries can present a choking danger to small children and may cause serious harm if ingested. Do
not leave them lying around and keep any spare batteries locked away at all times.
KIT 01
THE UPPER JAW
KIT 02
THE LOWER JAW
KIT 03
THE SKULL & JAWBONE
KIT 04
THE TIBIA &
RETRACTABLE JAW
STEPS & TIPS ONLINE
To help you get the best out of building the Xenomorph,
we’ve prepared a modellers checklist with hints, tips and advice
from our expert. The information below is aimed at making your build
as enjoyable and professional as possible right from the start.
Before you start...
Make sure you have good ventilation
when using adhesives and to replace
caps rmly.
Always use the correct adhesives and
always follow manufacturers guidance.
Apply glue sparingly and use a cocktail
stick to apply so that you don’t use too
much nor apply the glue too heavily.
Work in a well lit area. Use an
anglepoise lamp or similar on your work
bench to ensure you have good light
whenever you’re at work.
Organise storage – stackable, labelled
containers like old clean takeaway or
ice-cream plastic tubs with lids are
perfect. Small parts which may not be
needed until a later kit should be kept
in clear plastic and labelled bags.
Use masking tape to hold parts
temporarily in place.
Only use the correct size screwdriver
that ts the screw head rmly.
Cut parts from a sprue (framework)
with side cutters or a craft knife.
Side cutters tend to be easiest.
Keep your own build diary – note
mistakes and what went well along
with tips for future builds.
Use a magnet to help nd screws that
have fallen on the oor.
Leave parts in the paper bags supplied
until they are needed - you won’t think
you’ll get confused but it’s easy to get
overwhelmed by too many small similar
pieces. You can write a note of the kit
and part on the paper bag too.
If a screw is tight, try turning a half
turn forwards followed by a quarter turn
backwards. Also, it can sometimes help
to temporarily t a screw into its hole
before assembling the parts.
Always use the correct tools for each
part of the build.
But most of all, enjoy your build!
•Screwdiver – crosspoint (PH0 or similar)’
•Glue – superglue (cyanoacrylate)
•Cocktail sticks
•Tweezers
•Long-nosed pliers
•Cutting mat
• Needle les (smooth rough edges and remove excessive paint)
•Masking tape
•Small vice
•Small spring clamps
•Forceps
•Small clear plastic bags
•Permanent marker pen (for labelling storage boxes and bags)
•Magnifying glass
Tools (in rough order of priority)
Some parts of the model are attached using screws whilst some
simply push-t together. Other parts will need to be glued in
place using superglue (Cyanoacrylate or CA). Always follow the
manufacturers guidelines and warnings, apply sparingly and use in a
well ventilated space. Superglue gel (thick superglue) can be applied
with pin-point accuracy to the relevant surface using a cocktail stick.
Where possible, parts should be test-tted in place before glueing.
The instructions are numbered to indicate the correct order of
construction and also include tips and tricks to make the assembly
of the model as easy as possible.
To protect the paint nish on the components use a clean piece of
white paper on your work surface to build on.
Take care when opening the moulded packaging and try to leave
parts in their recesses until required to avoid losing pieces.
Always read through the instructions carefully and study the
illustrations before starting the assembly.
PB 1
ASSEMBLY GUIDE
The rst phase of the model’s assembly starts with the upper jaw,
which will become part of the Xenomorph’s skull.
KIT 1: THE UPPER JAW
PARTS SUPPLIED
Ref. Name Qty.
1-1 Skull A 1
1-2 Upper Jaw A 1
1-3 Upper Jaw B 1
1-4 Upper Tooth 1 A 1
1-5 Upper Tooth 2 B 1
1-6 Upper Tooth 3 C 1
1-7 Upper Teeth 4 D 1
1-8 Upper Tooth 5 E 1
1-9 Upper Tooth 6 F 1
1-10 Upper Tooth 7 G 1
1-11 Screwdriver 1
1-12 Screws 2x6mm 4*
1-1 1-2
1-3
1-4 1-5 1-6 1-7 1-8 1-9 1-10
1-11 1-12
* A spare screw is also supplied in case of loss or damage.
23
1-2
1-1
1-6 (C)
1-5 (B)
1-4 (A)
1-3
1-12
1-12
1-12
KIT 1: THE UPPER JAW
2
1
EXPERT TIP: If the screws
are difcult to t, it could be
because they are cutting a thread
as they are being screwed in. If this
should be the case, try turning the
screw forwards half a turn, then
back a quarter of a turn. Repeat
this process until the screw is
rmly secured in place.
To begin the assembly, place the Skull
1-1 upside down on the work surface.
Orientate the Upper Jaw A 1-2 so that
the three screw holes align with the
clear raised sockets on Skull part 1-1.
Using the Screwdriver 1-11, or similar,
x the two parts together with three
2x6mm 1-12 screws. Ensure the parts
t snugly together and the screws are
fully seated.
Place the Upper Jaw B 1-3 on a at
surface with the teeth sockets facing
upwards. The teeth are individually
embossed with a letter to help
identify them. The Teeth 1-4 (A),
1-5 (B) and 1-6 (C) are tted into
their corresponding sockets on the
right hand side, as shown. Test-t
the teeth, noting how the sockets
are individually shaped. When you
are happy with the t, apply a small
amount of superglue in their sockets
and secure the teeth rmly in place. A
cocktail stick or similar is useful when
applying small amounts of glue.
23
1-8 (E)
1-9 (F)
1-10 (G)
1-3
Parts that look similar often have letters or markings on them to help
differentiate between them. For example, the teeth in this issue have the
letters A to G embossed on them.
1-4 (A) 1-5 (B) 1-6 (C) 1-7 (D) 1-8 (E) 1-9 (F) 1-10 (G)
KIT 1: THE UPPER JAW
3
In a similar way to the previous step,
t the remaining Teeth 1-8 (E),
1-9 (F) and 1-10 (G) into their
corresponding sockets in the Upper
Jaw B 1-3.
PB 4
KIT 1: THE UPPER JAW
The construction uses several types of screw which
differ in size, colour and material. The screws are
supplied in separate packaging and a spare is
usually included for each type. Keep these extra
screws safe and labelled in case a replacement is
required.
KIT 1 IS COMPLETE
1-7 (D)
1-3
1-3
1-2
4
5
The Upper Teeth 1-7 (D) are tted
into the central cavity at the front of
the Upper Jaw 1-3. After test-tting,
apply a small drop of superglue and
x the teeth in place.
The Upper Jaw B 1-3 is fitted into
the Upper Jaw A 1-2, as shown.
Test-fit the large rectangular peg
on part 1-3 into the corresponding
rectangular recess on the underside
of part 1-2. Apply a little superglue
to the peg and secure the parts
firmly together.
PB 1
ASSEMBLY GUIDE
2-1 2-2 2-4 2-3
2-5 2-6 2-7 2-8
2-9 2-10 2-11
In this kit you will assemble the lower jaw pieces and
parts of the retractable jaw.
KIT 2: THE LOWER JAW
PARTS SUPPLIED
Ref. Name Qty
2-1 Lower Jaw A 1
2-2 Lower Jaw B 1
2-3 Lateral Lower Jaw A (left) 1
2-4 Lateral Lower Jaw B (right) 1
2-5 Retractable Jaw 1 1
2-6 Retractable Jaw 2 1
Ref. Name Qty
2-7 Retractable Jaw 3 1
2-8 Retractable Jaw Gearbox 1
2-9 Connecting Pin 1
2-10 Spring A 1
2-11 Screws 2.3x6mm 3*
* A spare screw is also supplied in case of loss or damage.
23
The Retractable Jaw Gearbox 2-8
is also needed in this step. Turn the
Jaw assembly over and firmly push
the rectangular peg on the Gearbox
2-8 into the matching recess in Jaw
part 2-5;this is a push fit connection.
Keep the assembly safely aside until it
is needed in the next kit.
Next, take Retractable Jaw part 2-5,
the Spring 2-10 and two 2.3x6mm
screws 2-11 and arrange them as
shown. Push one end of the Spring
2-10 onto the cross shaped peg
inside Jaw 2-5. Join the two halves
of the Retractable Jaw together
taking care that the other end of the
Spring 2-10 fits into the circular
recess in Jaw part 2-7. Secure
the two parts together using two
2.3x6mm screws 2-11.
1
3
2
2-6
2-7
2-9
2-7
2-6
2-5
2-5
2-6
2-7
2-8
2-10
2-11
2-11
KIT 2: THE LOWER JAW
Place parts 2-6, 2-7 and 2-9 on
the work surface, as shown. The
Retractable Jaw 2-6 fits between
the end of Jaw part 2-7. Align the
holes in the two parts and push the
Connecting Pin 2-9 through the
holes to join the parts together.
23
Take the Lower Jaw parts 2-1 and
2-2. Note how the rectangular peg on
Jaw 2-2 ts into the matching recess
on Lower part 2-1. Apply a little glue
in the recess and press the two parts
rmly together. Make sure the parts are
secured together before continuing.
KIT 2: THE LOWER JAW
4
2-2
2-1
5
2-1
2-3
EXPERT ADVICEEXPERT ADVICE
Protect painted parts from damage during
assembly by working on a cutting mat or a
sheet of cardboard. To clean components,
use a soft, dry cloth so as not to damage your
Xenomorph. Remove dust from intricate items
using a soft brush.
The Lower Lateral Jaw 2-3
is fitted to the left side of
the Jaw 2-1. There are five
circular sockets on Jaw part
2-1 into which pegs on Jaw
2-3 fit. Jaw part 2-1 may
need to be bent slighty for
the pegs to align. As part
2-3 will need to be removed
in a later issue, do not glue
in place. If necessary, use a
small piece of masking tape
to temporarily hold the part
in place.
Inhaltsverzeichnis
Andere Hachette Spielzeug Handbücher
Hachette
Hachette ALIEN PACK 4 Handbuch
Hachette
Hachette U-BOAT U 96 Bedienungsanleitung
Hachette
Hachette ALIEN PACK 6 Handbuch
Hachette
Hachette AGORA MITSUBISHI A6M ZERO FIGHTER Handbuch
Hachette
Hachette ALIEN spectacular Produktinformationsblatt
Hachette
Hachette ALIEN PACK 8 Handbuch
Hachette
Hachette Agora Models BISMARCK Handbuch
Hachette
Hachette ALIEN PACK 7 Handbuch
Hachette
Hachette ALIEN Bedienungsanleitung
Hachette
Hachette AGORA BISMARCK THE LEGENDARY BATTLESHIP Handbuch
