Halma Ocean Optics TR2 Bedienungsanleitung
Engineering Note
Topic: TR2 Information
Product Affected: TR2 Temperature Regulator, S2000 Spectrometer
Date Issued: 8/29/2002
Operation
The TR2 is a Temperature Regulator unit that stacks onto the S2000 Spectrometer. The TR2 displays
two temperature values (in oC), the set temperature and actual temperature. The TR2 has two controls,
a set point pushbutton and a toggle switch. The display can toggle between viewing the actual
temperature and the set-point temperature. With the pushbutton pushed out, the display shows the
actual temperature. The set-point temperature is viewed by pressing the pushbutton in.
The temperature is set by a digitally controlled potentiometer with 100 set points. To adjust the set-
point, press the pushbutton and then increment or decrement the toggle switch to the desired
temperature. The set-point is stored in a volatile memory location. To store the set point permanently,
press the toggle switch to the down position and then press the set button. This action will lock the set
temperature into permanent memory.
A standard TR2 can be adjusted between 0°C and 37°C. However the TR2 is only capable operating
15°C below the ambient temperature. At cool temperatures, the operator must insure that
condensation does not occur on the inside of the optical bench. By design, the maximum
temperature set-point is 37°C.
The TR2 requires a regulated +12V power supply that delivers at least 2 amps. Poor results may be
obtained if a non-regulated power supply or a supply that cannot deliver adequate current is used. The
power connection is configured for a positive center polarity.
The TR2 indicates its status with a two color LED. The status conditions are defined as follows:
• Green – The TR2 has reached temperature stability (within 0.1oC).
• Red – The TR2 has not reached temperature stability.
• Blinking Red – The TR2 is not running. Reset by pushing the pushbutton.
The S2000-TR2 system operates from two power supplies: the 5V from the ADC Card and the +12V
from the external power supply. Depending on the order in which power is applied, the TR2 may
power-up with a blinking red LED. To clear the blinking LED, press the pushbutton to reset the unit.
209-00000-000-04-0704 1
TR2 Information Engineering Note
Pin Out
The TR2 interfaces to the S2000 using the H1 & H2 connectors. The pin-out for these signals is show
below. In addition, the TR2 has a J3 connector that communicates the various temperature signals. Its
pin-out is shown in Table 1 below.
When Multiple S2000-TR2 assemblies are stacked together, several signals in the J3 connector must
be connected among all of the TR2 boards in the stack. The Table 1 below defines these signals. In
this condition, the display will only show the actual and set-point temperatures from a single unit.
Typically, this unit is the Master Spectrometer Channel.
Table 1: J3 Definition
Pin Signal Name Connections Description
1 N/C No Connect
2 VTEMP From one TR2
(Master) Analog signal of the current temperature. Scaling is
100mv/oC
3 Reset All Reset signal for TR2—Active Low
4 VSET From one TR2
(Master) Set-point temperature signal to be displayed when
pushbutton is depressed. Scaling is 100mv/oC)
5 Ground All +5V Ground
6 Vdisplay From one TR2
(Master) Analog Signal that is displayed. Scaling is 100mv/oC
7 Toggle Down All Clock signal to toggle the set-point down one increment—
Active Low
8 N/C No Connect
9 Ground All +5V Ground
10 Toggle Up All Clock signal to toggle the set-point up one increment—
Active Low
2 209-00000-000-04-0704
TR2 Information Engineering Note
Table 2: S2000-H1 Header Pins (Analog) Table 3: S2000-H2 Header Pins (Digital)
1 Analog Channel 0 D N/C
2 Analog Channel 1 C A/D Trigger
3 Analog Channel 2 B Software Trigger In (D3)
4 Analog Channel 3 A Trigger Mode Select (S1)
5 Analog Channel 4 1 GND
6 GND 2 +5 VDC
7 Reserved 3 F Clock
8 Analog Channel 7 4 Readout Gate
9 Analog Channel 6 5 Reserved
10 Analog Channel 5 6 Temperature (optional)
7 Read Enable
8 Trigger Mode Select/Strobe Enable
(S0)
9 Single Strobe Out
10 Continuous Strobe Out
11 Integration Clock
12 Master Clock
TR2 Control Signals
It is possible to drive the control signals (Toggle Up/Down and Reset) directly. These signals are 5V
TTL Active LOW signals that are pulled HIGH on the TR2 board.
To change the current set point, drive the Reset signal LOW and then pulse the Toggle Up or Toggle
Down LOW. Each falling edge of the Toggle Up/Down signal will drive the set point one position in
the desired direction. Once the desired set point is reached, drive (or release) the Toggle Up/Down
signals HIGH and then drive (or release) the Reset signal HIGH. The Toggle Up/Down signals are de-
bounced on each TR2 and the minimum pulse width is 100ns. There is no maximum pulse width.
To change the nonvolatile power-up set point, hold the Toggle Up/Down signal LOW while the Reset
signal is driven (or released) HIGH. This writes the current wiper setting to the nonvolatile memory
location that is read from upon power-up of the unit.
209-0000-000-04-0704 3
TR2 Information Engineering Note
4 209-00000-000-04-0704
Dieses Handbuch passt für folgende Modelle
1
Andere Halma Messgerät Handbücher
Halma
Halma ALICAT SCIENTIFIC M Bedienungsanleitung
Halma
Halma Ocean Optics HR2000 Series Bedienungsanleitung
Halma
Halma Alicat Scientific L Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC MB Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC MB Bedienungsanleitung
Halma
Halma Alicat Scientific CODA KM Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC L Bedienungsanleitung
Halma
Halma Ocean Optics NIRQuest512-1.7 Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC L Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC L Bedienungsanleitung
Halma
Halma Ocean Optics DH-mini UV-Vis-NIR Bedienungsanleitung
Halma
Halma Sensitron SMART 3 NC Bedienungsanleitung
Halma
Halma Alicat Scientific CORIOLIS CODA Series Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC L Bedienungsanleitung
Halma
Halma Ocean Optics Red Tide USB650 Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC L Bedienungsanleitung
Halma
Halma SENSITRON SMART S Bedienungsanleitung
Halma
Halma Ocean Optics JAZ Bedienungsanleitung
Halma
Halma ALICAT SCIENTIFIC M Series Technisches Datenblatt
Halma
Halma ALICAT BC Series Bedienungsanleitung
